835 W. 41st Street Tulsa, Oklahoma 74107 www.motorguide.com © 2005, MotorGuide FCC and IC Compliance Statement FCC ID #MVUFP01, MVUFP02 IC ID 6094A-FP01, 6094A-FP02 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device complies with FCC Rules.
Congratulations … on your purchase of the MotorGuide Wireless Trolling Motor. This motor has been designed, engineered, and manufactured to give you the best possible dependability and exceptional performance for years of enjoyment.
TABLE OF CONTENTS General Information GENERAL INFORMATION ....................................................................2 Safety DO’s and DON’Ts ...................................................................3 Operating Safety ................................................................................4 NOTES: ..................................................................................................5 Features & Components FEATURES........................................................
Maintenance MAINTENANCE ...................................................................................21 Foot-Pedal Battery Replacement .....................................................21 Care & Cleaning Instructions ...........................................................22 Customer Responsibilities................................................................22 Battery..........................................................................................22 Freezing Temperature Storage....
MOTORGUIDE WIRELESS NOTES: ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ _______
MOTORGUIDE WIRELESS GENERAL INFORMATION Please read and retain this manual. The information within describes the proper procedures for safely installing, operating and maintaining your motor. ! WARNING Failure to follow a safety WARNING can result in bodily injury. CAUTION Failure to observe CAUTION instructions can result in failure or damage to the product or equipment. INFORMATION The information symbol signifies important information about your trolling motor.
MOTORGUIDE WIRELESS CAUTION Disconnect the trolling motor from the battery(s) before charging. How to Use This Manual Review the following information carefully. These notices will alert you to potential dangers and important information. The observance of WARNINGS and CAUTIONS alone does not eliminate the possibility of personal injury or product damage.
MOTORGUIDE WIRELESS ! Circuit Protection – MotorGuide recommends installing a 50 amp manual-reset circuit breaker and power switch in line with the trolling motor positive leads within (1.8 m) 72 inches of the battery(s). To order a circuit breaker kit, contact your local Service Dealer, request kit number MM5870. See the “Accessories” section of this manual for more information. Operating Safety 1.
MOTORGUIDE WIRELESS NOTES: ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ _______
MOTORGUIDE WIRELESS Lower Unit FEATURES Cradle Lock Mount Composite Column Top Housing Wireless Foot-Pedal Remote Capabilities The MotorGuide Wireless uses a remote foot-pedal with the receiver built into the trolling motor mount. These remote capabilities work with the Digital Remote Control (DRC) product and up to four remotes (including the footpedal) can be used with one motor. See the “Accessories” section of this manual for more information.
MOTORGUIDE WIRELESS On/Off Button COMPONENTS Wireless Remote Foot-Pedal Slower Button The remote foot-pedal functions include the off/on, right/left and faster/slower motor operations. The anti-slip design makes motor operation easy for the angler wearing large boots. The battery used in the foot-pedal is long-life, inexpensive and replacement is easy. Left Button Faster Button Right Button Lower Unit The lower unit is available in a 12 or 24 volt variable speed motor.
MOTORGUIDE WIRELESS Prop The MotorGuide Wireless uses the 3½ inch two blade Power Prop. Cradle Lock™ Mount The rock solid design of the MotorGuide Wireless mount has a quick-release mounting plate and an easy access lever for trouble-free stowing and deploying the motor. The mount also features a cradle that protects the motor during rough-water runs. Battery Indicator The MotorGuide Wireless is equipped with a battery charge indicator.
MOTORGUIDE WIRELESS NOTES: ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ _______
MOTORGUIDE WIRELESS INSTALLATION Mount Installation It is recommended that two people install the motor and mount. ! WARNING Do not connect the motor to a power source until the motor and mount are fully installed on the boat. The tools required for the installation are: 5 1) Drill with (8 mm) /16 inch drill bit 2) #3 Phillips head screw driver 1 3) /2 inch open end wrench 1) Carefully select the area on the deck as close to the centerline as possible to install the mount.
MOTORGUIDE WIRELESS 4) Place the mount base plate on the boat deck aligning the holes on the plate to the holes on the deck. Install the four (4) stainless steel mounting bolts through each of the mounting holes. 5) Install the four (4) stainless steel washers and nuts on the bottom side of the deck and tighten securely. 6) Remove the packaging material, in the box, from around the trolling motor. 7) Lift the motor and mount out of the box, turn the mount upright and and lay it on a flat surface.
MOTORGUIDE WIRELESS 10) Sit the back of the mount housing over the back of the mount base. Press down on the back of the mount base and turn the mount locking knob just enough to engage the cam locking mechanism and secure the mount onto the base plate. Complete tightening the cam locking mechanism in step 12 below. Mount Locking Knob 11) Position the depth collar on the shaft so that the lower unit will not strike any obstacles (boat trailer, ground, etc.
MOTORGUIDE WIRELESS For storage and security purposes the MotorGuide Wireless Cradle Lock™ mount makes it easy to completely remove and reinstall the mount and motor. When the mount and motor are removed from the boat, a snap-on Wireless Mounting Plate Cover (see the Accessories section of this manual for order information) is available to protect the mounting plate. Wiring & Battery Information ! WARNING Batteries contain sulfuric acid which can cause severe burns.
MOTORGUIDE WIRELESS Important: Do not route a transducer cable down the trolling motor power cord. Route the transducer cable down the side of the mount, then into the bow console. Provide enough excess sonar cable to allow the motor to make three (3) complete 360 turns. Electronics, depth finders in particular, should be connected directly to the main engine or an accessory battery. Do no connect your electronics to the trolling motor battery.
MOTORGUIDE WIRELESS of six (6) gauge (13 mm) wires if extending the existing wire beyond the standard battery cable supplied with the product. Bow Plugs – MotorGuide recommends the use of a quality plug designed for marine applications.
MOTORGUIDE WIRELESS 24 Volt Battery Hook-up C D F A G E B A) B) C) D) Battery A Battery B To trolling motor connections Black battery leads (-) G E) Red battery leads (+) F) 50 amp circuit breaker and a power switch G) Jumper wires Connect the black battery lead from the power cable to the negative (-) post on battery A and the red lead from the power cable o the positive (+) post on battery B. Connect a jumper wire between the negative (-) post of battery B and the positive (+) post of battery A.
MOTORGUIDE WIRELESS Activating the Foot-Pedal Electronic ID Each foot-pedal has a unique electronic ID number. Up to four electronic ID numbers (Digital Remote Control units and/or foot-pedals) can be stored by your receiver. For your foot-pedal to respond to your commands only and not those of other boaters, you must activate the electronic ID number into your receiver. Follow the instructions below (one time only) to activate each new remote control device: 1. 2. 3.
MOTORGUIDE WIRELESS MOTOR & MOUNT OPERATION Adjusting the Motor Depth and Deploying the Motor 1. Loosen the depth collar by turning the knob handle. Slide the depth collar up or down the shaft to a position that will allow the lower unit to be submerged at least 12 inches (30cm) below the water surface when the motor is fully deployed. When the depth collar is in the desired location, turn the depth collar handle to tighten.
MOTORGUIDE WIRELESS Stowing the Motor 1. Pull up the release handle and then, holding the shaft or top housing, lift the motor up. Release Handle 2. While lifting the motor out of the water, rotate the shaft until the lower unit is aligned with the locking cradle. Lower Unit Aligned with Locking Cradle 3. Lower Unit Locked in Cradle 4. Continue to pull the lower unit up to the mount until the lower unit can be snapped into the cradle.
MOTORGUIDE WIRELESS Operating the Foot-Pedal INFORMATION Ensure the foot-pedal electronic ID has been activated. See the “Installation” section of this manual for instructions. On/Off Button 1. Slower Button Prop On/Off Turn the prop on or off by pressing the center button and it will alternate between on and off. The “on” condition is indicated by a short beep while “off” is indicated by a long beep. Left Button Faster Button Right Button 2.
MOTORGUIDE WIRELESS MAINTENANCE Foot-Pedal Battery Replacement Use only a 3V lithium type CR2032 replacement battery. These batteries are not rechargeable. Follow these instructions to change the battery: 1. Remove the five screws on the battery cover plate located on the underside of the foot-pedal. Location of Screws Securing Battery Cover Plate to Foot-Pedal 2. Remove the battery cover plate. 3. Using a pencil, push the battery out of its holder. 4. 5. Ensure the Oplace on the cover.
MOTORGUIDE WIRELESS Care & Cleaning Instructions To keep your trolling motor looking its best: 1. Periodically wash it with warm soapy water and a soft cloth or sponge. 2. Do not use a high pressure or power washer. 3. Use a vinyl/rubber UV protector, available in any auto store, to keep the cables looking fresh. 4. Never use harsh chemicals, alcohol, solvents or abrasives on the motor plastics, rubber or painted parts.
MOTORGUIDE WIRELESS Freezing Temperature Storage Store your trolling motor where it will not be affected by freezing temperatures. Installing or Replacing the Propeller Propeller Propeller Pin Propeller Nut See the “Accessories” section of this manual to order a replacement propeller. CAUTION Make sure the motor is disconnected from the battery before replacing the propeller. CAUTION Do not strike a bent prop pin with a hammer to remove the pin.
MOTORGUIDE WIRELESS mallet. If necessary, repeat the procedure on all blades until the propeller comes off. 4) If the propeller pin is bent, replace it. 5) Align the new propeller with the propeller pin. 6) Reinstall the propeller nut and tighten securely with your fingers. Tighten another 1/4 turn using a MotorGuide Prop Wrench, part number MGA050B6. 90-MM5997 For Questions, Contact Consumer Affairs at #1-920-929-5040 © 2005, MotorGuide www.motorguide.
MOTORGUIDE WIRELESS TROUBLESHOOTING Frequently Asked Questions Q The receiver beeps when I press a button on the foot-pedal but nothing happens. A The receiver does not have the foot-pedals electronic ID number programmed; refer to the “Activating the Electronic ID number” section of this manual. Q Activating the electronic ID number does not work. A The receiver’s memory might be full, see the “Erasing the Receiver’s Memory” section of this manual.
MOTORGUIDE WIRELESS Motor makes excessive noise or vibrates excessively Motor fails to run at any speed Motor loses one or more speeds • The propeller may be fouled. Remove the propeller; clean or replace if necessary. • The propeller may be loose. Check to see if the propeller is secure. • The armature may be bent. Remove the propeller and set the motor at medium speed. Turn the unit on and look for the shaft to wobble. • The magnets may be interfering with the armature. Turn the power is off.
MOTORGUIDE WIRELESS INFORMATION Refer to your nearest Service Dealer for assistance with trolling motor repairs. FOR REPAIR SERVICE Contact your nearest MotorGuide Service Dealer. See a complete listing of Service Dealers in the US and Canada at our MotorGuide web site: www.motorguide.com. Call Mercury Marine Consumer Affairs to obtain the name and location of the Service Dealer nearest you.
MOTORGUIDE WIRELESS MOTORGUIDE ACCESSORIES Making It More Perfect. Who says you cannot make the best even better? MotorGuide® factory accessories let fishermen customize motors to their own unique needs. In addition, every one is a perfect fit. REPLACEMENT PROPS Prop Description Number #12 3.5" 2 Blade Power Prop MGA0495 #16 3.5" Machette III, 3 Blade MGA087B ADDITIONAL HARDWARE ACCESORIES Prop Wench MGA050B6 Comes complete with spare prop nut and two prop pins, allowing fast prop changes.
MOTORGUIDE WIRELESS MOTORGUIDE LIMITED THREE-YEAR WARRANTY (Keep your original purchase receipt) For recreational use customers, MotorGuide Tour, Digital Freshwater, Digital Steering, and Saltwater Series electric trolling motors are warranted to the original retail purchaser1 to be free from defects in material and/or workmanship for a period of three (3) years from the date of purchase.
MOTORGUIDE WIRELESS IMPORTANT!! REGISTER YOUR PRODUCT The warranty registration card (located in the box) should be completed and mailed to Mercury Marine to validate your warranty. To replace a lost warranty card, contact the Mercury Marine Registration Department at 1-920-929-5054. WARRANTY CARD REGISTRATION IS INCLUDED IN THE BOX AND IS SEPARATE FROM THIS MANUAL. PLEASE FILL OUT AND MAIL IMMEDIATELY TO VALIDATE YOUR WARRANTY. Thank you for purchasing and registering this MotorGuide product.
MotorGuide 835 W.