Instruction manual

ManualsBrandsMorphy Richards ManualsDomestic Appliances131000

Place a vessel underneath the Dispense Nozzles

(6) and press the Dispense Button (5) to reset the

system. This takes approx. 25 seconds. Any water

dispensed during resetting should be discarded.

Press the Start/Stop Button (1), the Hot Water

Dispenser will pump 240ml of water into the

heating chamber and start to heat.

Using the Water Volume Dial (2), adjust the

Dispense Volume (15) to 240ml. Place a cup on the

Drip Tray (8) under the Dispense Nozzles (6).

When heated the water will automatically

dispense from the Dispense Nozzels (6) into your

cup.

Remove the Water Tank (7) from the Main Unit

(23). Remove the BRITA MAXTRA Cartridge (19) and

BRITA Hopper (21) from the Water Tank.

Fill the Water Tank with cold water and return to

your Hot Water Dispenser. Plug your Hot Water

Dispenser into the electrical socket.

Quick

Start

Guide

This quick start guide shows you the basic steps

for dispensing 240ml of hot water for a single

cup of tea or coffee. This quick start guide does

not detail the steps to use the BRITA Filtration

System.

For more detailed information on using your

new Hot Water Dispenser or BRITA Filtration

System, please read this instruction manual.

KT131000 MUK REV3.indd 7 24/03/2014 09:06

Summary of content (12 pages)

PAGE 1
Quick Start Guide This quick start guide shows you the basic steps for dispensing 240ml of hot water for a single cup of tea or coffee. This quick start guide does not detail the steps to use the BRITA Filtration System. For more detailed information on using your new Hot Water Dispenser or BRITA Filtration System, please read this instruction manual. 1 Remove the Water Tank (7) from the Main Unit (23). Remove the BRITA MAXTRA Cartridge (19) and BRITA Hopper (21) from the Water Tank.
PAGE 2
Resetting The System Before using your Hot Water Dispenser for the first time, or after it has been unplugged from the mains. You must perform the following steps to reset your Hot Water Dispensers’ heating chamber. Your Hot Water Dispenser will not function if the system has not been reset. 1 Plug your Hot Water Dispenser into the mains outlet and switch on at the socket. 2 If the Water Tank (7) is empty, the Empty Tank Icon (12) will illuminate and flash.
PAGE 3
BRITA filtration Filtering your water improves the taste and appearance of beverages by reducing limescale, lead, chlorine and other impurities. The BRITA MAXTRA Filter Cartridge offers improved filtration due to MAXTRA Technology. The natural MicroporeFilter in combination with the powerful Protect Filter reduces chlorine and limescale for a great natural taste and further reduces metals such as lead and copper. Unique flow control ensures the perfect filtration time for best results.
PAGE 4
Using the Hot Water Dispenser Before using your Hot Water Dispenser, or if it has not been used for over a week, follow these instructions to boil the maximum amount of water, then discard to ensure the system is flushed through. The following instructions detail the steps to Filtering water through the BRITA Maxtra follow to use your Hot Water Dispenser. For Cartridge takes around 4 minutes for 1.5L.
PAGE 5
Turn the Water Volume Dial (2) to adjust the Dispense Volume (15). Your Hot Water Dispenser can heat between 150ml to 1.5L of water per cycle. 6 You can automatically dispense volumes of water at 600ml and below. To turn this feature on or off, press the Dispense Button (5). This function cannot be selected for volumes over 600ml. These must be dispensed manually. 7 Press the Start / Stop Button (1) to begin heating. Your Hot Water Dispenser will sound and the heat cycle will begin.
PAGE 6
Drinks Temperature Getting the correct water temperature is essential if you are to enjoy your favourite hot drinks with maximum flavour and taste. E.g. If you’re a green tea drinker then water that is brewed too hot will scorch the leaves creating a bitter taste. Auto / Manual Dispense Press the Temperature Button (4) to cycle through the options (85,95 & 100oC). The water temperature will be displayed on the screen (17).
PAGE 7
Multiple Cups Multiple cups can be filled quickly and easily by starting and stopping the dispense cycle and exchanging vessels. 1 Set your Hot Water Dispenser unit to heat a desired amount of water with the Auto Dispense featue switched off. Place two cups under the Dispense Nozzles (6) and dispense the water by pressing the Dispense Button (5). Cancel the heating cycle To cancel the heating cycle at any time, press the Start / Stop Button (1).
PAGE 8
Drip Tray 3 When the crystals have dissolved, set the unit to heat 1.5 litres of water to 85 degrees. Do not boil to 100 degrees 4 Leave the Hot Water Dispenser for 10 minutes. Do not dispense the water! The Drip Tray Indicator (10) indicates that the Drip Tray (8) is full and must be emptied. To empty, pull the drip tray outwards until it is free from the runners and discard the contents. CAUTION! The contents of the drip tray may be hot.
PAGE 9
Volume Guide Mugs and cups vary by size. The measurement table (below) is a guide to volumes for different vessels. These will vary dependant upon your vessel size and requirements. Vessel We recommend measuring the volume of your vessels and noting it down for future use. Capacity Vessel Capacity 1 cup 150ml - 180ml Cafetière 750ml - 1L 2 cups 300ml - 360ml Teapot 1.1L - 1.4L 1 mug 180ml - 380ml Noodle pot 230ml - 300ml 2 mugs 360ml - 660ml Pan 750ml - 1.5ml KT131000 MUK REV3.
PAGE 10
Contact Us Helpline If you are having a problem with your appliance, please call our Helpline, as we are more likely to be able to help than the store you purchased the item from. Please have the product name, model number and serial number to hand when you call to help us deal with your enquiry quicker.
PAGE 11
Registering your 2 year guarantee Exclusions Your standard one year guarantee is extended for an additional 12 months when you register the product within 28 days of purchase with Morphy Richards. If you do not register the product with Morphy Richards within 28 days, your product is guaranteed for 1 year. To validate your 2 year guarantee register with us online at Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: www.morphyrichards.co.
PAGE 12
LCD Display Glossary Below are some of the icons that may highlight during use, and their meaning. Refer to the instruction book for more information on the settings. Reset Water Tank Auto Dispense Heat Icon Water Still to Dispense Descale After the Hot Water Dispenser has been switched on, The Dispense Icon (13) and the Dispense Button (5) are flashing. The system needs to be reset before use. Follow the instructions under ‘Resetting the System’ (page 4).