1. what’s in the box Please consult below checklist for all the components. USB Cable Video Doorbell User Guide Indoor Chime Screw & Tools Adhesive Tape 2.
4. Battery installation insulation film The batteries are pre-installed in the doorbell, with an insulation film inserted in the positive poles. Please remove the film and insert the battery pack back to compartment, with positive poles upwards! NOTE: Improper battery installation will cause damage to the internal components and may result in serious injury. 5. Battery charging The batteries inside the doorbell are not fully charged in accordance with transportation safety regulations.
Guiding steps: 9:55 9:55 9:55 Devices Camera Doorbell Battery Camera Floodlight Camera Please follow the instruction manual to power the device Help device(please consult the user manual for more on Wait for the LED indicator to flash RED Network Video Recorder Tap Next Next Next Me 1. Tap “+” to add device 9:55 2. Select Doorbell 3. check power status 9:55 Wi-Fi Setup 15~25cm (Please select a 2.4G network, this device will not work with 5G Wi-Fi networks) 4.
9. Live viewing Quit live viewing Setting menu Battery status Volume on/off HD/SD switch Full screen display Stream bit rate 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Wi-Fi signal status Screenshot button Speak to the scene Record on the phone Body detection on/off Notification history Cloud storage service HD Note: Live viewing will not trigger device recording. Live view interface 10.
11. leave Voice messages Maximum 3 voice messages (Max. 10 seconds each) can be pre-recorded into the doorbell, which enables you to quickly respond to your visitors when you are not convenient to answer the doorbell call.
Sharing by QR code scanning The new users can show their QR codes to the administrator, and share device by QR Code scanning.
3). Press the doorbell button 2). Click reset button Reset Button LED Indicator Click the RESET button on the wireless chime only once, and you will see the LED indicator flashing blue, indicating the chime is in pairing mode. Press the doorbell button, and the Chime will sound to react. Pairing succeeds, and the indicator on the chime will be in solid blue. 4).
14. Installation 166° Select location Your doorbell has 166-degree view angle and 120-degree human detection range. It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance. 5 feet 160cm Hardwire your doorbell (Optional) The doorbell works with both 12V ~ 24V AC and 12V DC hardwire power source. Either wire can be connected to either terminal. The cable order doesn't matter. The Smiths 1.
Go wireless installation The Smiths 1. Dismount the bracket by pushing from the back of your doorbell. Please remove the insulation film in the battery cell. (Example) 2. Bracket installation: mount the bracket on 3. (Optional) The nameplate holder can be the wall with screws & anchors or the double mounted on the top rear/ bottom rear of the -sided adhesive tape. bracket, prior to bracket installation. The Smiths 4. Mount your doorbell to the fixed bracket.
15. Specification Video doorbell Video & Audio Image Sensor Indoor Chime General OS 1/2.7” CMOS (2.0MP) Lite-OS Power source DC 5V 1A Stream HD/SD dual stream Consumption Ringtones 0.2W Resolution Infrared LED Lense Angle of view Min. illumin. WDR Audio Power port 1920 × 1080 px High power IR LED with ICR Volume 1.7mm/F2.0 Volume control 166° Connection type Color: 0.01 Lux; B&W: 0.
16. Trouble shooting Q1: Why I failed to set up Wi-Fi for the doorbell? A1: .Device works with 2.4GHz Wi-Fi only, but not support 5GHz Wi-Fi. .Wi-Fi network is not good, try to keep the camera near the Wi-Fi router when setting up. .The Wi-Fi password is wrong. Please check if there are special characters in the password, or the network is specially encrypted. Q2: How do I know if I have 2.4G or 5G wifi? A2: Please check the user manual of your Router or call the network operator for help.