ASSEMBLY & OPERATING INSTRUCTIONS Liquid Propane Gas Grill Model No:M220 Model No:M200S Model No:M200R Model No:M200G Model No:M200B • Parts • Assembly • Safety Rules • Use and Care • Troubleshooting WARNING: Note to Consumer Leave this Owner’s Manual in a convenient place for future reference. Read this Owner’s manual carefully and be sure your gas grill is properly assembled, installed and maintained. Failure to follow these instructions could result in serious injury and/or property damage.
Table of Contents Safety Precautions WARNING Warranty-------------------------------------------------2 Safety Precautions---------------------------------3~4 Hardware List-------------------------------------------5 Assembly Diagram -----------------------------------6 Assembly List-------------------------------------------7 Assembly Instructions ---------------------------8~17 Lighting Instructions ----------------------------18~19 Cleaning and Maintenance ---------------------------20 Troubleshooting-
Safety Precautions A tank of approximately 12 inches in diameter by 181/2 inches high is the maximum size LP gas tank to use. You must use an OPD gas tank which offers an Overfill Prevention Device. This safety feature prevents the tank from being overfilled which can cause malfunction of the LP gas tank, regulator and/or grill. • Have your LP gas tank filled by a reputable propane gas dealer and visually inspected and re-qualified at each filling.
WARNING Burner Flame Check A strong gas smell, or the hissing sound of gas indicates a serious problem with your gas grill or the LP gas tank. Failure to immediately follow the steps listed below could result in a fire or explosion that could cause serious bodily injury, death, or property damage. • Shut off gas supply to the gas grill. • Turn the control knobs to OFF position. • Put out any flame with a proper fire extinguisher. • Open Grill Lid. • Get away from the LP gas tank.
Contents for Hardware Pack The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Tools required for assembly Philips Head Screwdriver (not included). Note: The left and right sides of the grill are on your left and right as you face the front of the grill.
Model M200S / M220 / M200R / M200G / M200B Assembly Diagram 6
Model M200S / M220 / M200R / M200G / M200B Assembly List To make sure you obtain the correct replacement parts for your gas grill, please refer to the part numbers on this page. Important: Use only parts listed above. When ordering parts, providing the following information: Important: Keep this Owner’s Manual for convenient reference and for part replacement. 1. Model # 2. Part Description 3.
Assembly Instructions Please insert Locking Caster(No.13) into the Cart Bottom Panel (No.11). Figure 1 2 1 3 Half screw out the screws in the bottom plate, then put Cart Right Side Panel(No.8)and Cart Left Side Panel(No. 15) onto the relevant screw holes and screw tightly.
1 4×A 2 Install Cart Back Panel(No.7) onto the relevant place with four A screws. Figure 3 1 2 Half screw out the screws in the bottom and side plates, then put Triangle Joint Parts(No.12) onto the relevant screw holes and screw tightly.
4×F Install Cart Front Bar(No.6) onto the relevant place with four F screws. Attention: magnet downward.
4×A Figure 7 Screw the grill body and the cart tightly with four A screws. 3 1 5×A 2×D 2 Screw Foldable Side Shelf Joint(No.27/28) tightly with A screw and D spacer inside the grill body.
3 1 5×A 2×D 2 Screw Foldable Side Shelf Joint(No.27/28) tightly with B screw and D spacer inside the grill body. Figure 9 1 2 Hook the Side Shelf (No. 4) into the hole which already installed Part No.
1 2 Hook the Side Shelf (No.4) into the hole which already installed Part No. 27 and 28. Figure 11 1× F 1 3 2 ! cut of two white plastic tie. Fixed Regulator connecting piece onto the Right plate with one F crew.
1×C Put the Spindle Below Door Panel(No.14) into the relevant hole in the bottom plate. Figure 13 2 1 Install the Door Handle(No.18) onto the Cabinet Door(No.16). Install the Cabinet Door(No.16) onto the Cart Bottom Panel(No.11).
2× F 3 2 1 1. Install Grease Tray(No.21) onto Grease Pan Bracket(No.23) with two F screws. 2. Put Grease Pan(No.22) into Grease Pan Bracket(No.23). 3. Put the grease tray into the grill body. Figure 15 2 1 3 Connect the Battery Wire. Paste the Battery Box(No.10) onto the side panel.
Put Warming Rack(No.24), Cast Iron Cooking Grid(No.5), Flame Tamer(No.19) into the relevant place. Figure 17 Install Gas Tank Holding Wire(No.9) onto the bottom plate. Pass Bottle Opener (No.25) through Cart Left Side Panel(No.15) and fix it on Bottle Opener Retainer (No.26).
Connecting LP Gas Tank to LP Grill 1. Place foot ring of 20 lb tank into the hole in bottom panel. Make sure the tank valve is in OFF position.(Fig.21). 2. Check the tank valve to ensure it has proper external mating threads to fit the hose and regulator assembly provided. 3. Make sure all burner valves are in OFF position. 4. Inspect the valve connection port and regulator assembly. Look for damage or debris. Remove any debris. Inspect hose for damage. Never use damaged or plugged equipment. 5.
Checking for LP gas leaks Never test for leaks with a flame. Prior to first use, at the beginning of each season, or every time your LP gas tank is changed, you must check for gas leaks. 1. Make a 50/50 (soap/water) mild soap solution. 2. Turn the control knobs to full OFF position. then turn gas ON at supply tank. 3. Apply the soap solution with a clean brush to all gas connections. See below. If growing bubbles appear in the solution the connections are not properly sealed.
If Grill Still Fails To Light 1. Check gas supply and connections for leaks. Check that all wire connections are secure. WARNING Never lean over the grill cooking area while lighting your gas grill. Keep your face and body a safe distance (at least 18 inches) from the cooking grid surface when lighting your grill by match. 2. Repeat basic lighting procedure.
Cleaning and Maintenance Cleaning Exterior Stainless Steel Surfaces To ensure a proper working unit the following proper care and maintenance is suggested. Cleaning Cooking Grids We suggest you wash your cooking grids in a mild soap and warm water solution. You can use a wash cloth or soft brush to clean your cooking grids. Cleaning Heat diffusers Periodically you should wash the heat diffusers in a soap and warm water solution. Use a soft brush to remove stubborn burnt-on cooking residue.
3. Inspect each burner for damage (cracks or holes) and if such damage is found, order and install a new burner. After installation check to ensure that gas valve orifices are correctly placed inside the ends of the burner tubes. Regardless of which burner cleaning procedure you use, we recommend you also complete the following steps to help prolong burner life. 1. Use a fiber pad or nylon brush to clean the entire outer surface of each burner until free of food residue and dirt.
Cooking Instructions WARNING Do not leave the grill unattended. Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch cooking surfaces, grill housing. Grill Lid or any other grill parts while the grill is in operation, or until the grill has cooled down after use. Failure to comply with these instructions may result in serious bodily injury.
Grill Cooking Chart WARNING: To ensure that it is safe to eat,food must be cooked to the minimun internal temperatures listed in the table below.
WWW.MONUMENTGRILLS.COM Scan the QR code on Facebook Join our 'Monumentgrills Lifestyle' group and receive 15% off for accessories purchase, along with access to exclusive benefits such as coupons, recipes, and giveaways shared within the group.