User's Manual

K7903G516_US_front_A
K7903G516_US_back_A
1. Package Contents :
RF Keyboard & Mouse Combo
Function :3. Installation :
2. Install the Batteries :
QUICK GUIDE
OFF
ON
Wireless RF Keyboard & Mouse not detected
If the Keyboard & Mouse don't respond to activity, follow this steps :
(1) Ensure that the receiver cable is properly connect to the USB ports.
(2) Ensure that the batteries have been installed correctly.
(3) Ensure that you have established a connection between the RF receiver, the
mouse and the keyboard.
If the RF Keyboard & Mouse don't respond to activity after replacing. The
batteries, follow these steps :
(1) Ensure that the batteries have been installed correctly.
(2) Ensure that the batteries are not discharged.
(3) Ensure that you have established a connection between the RF receiver, the
mouse and the keyboard.
This device complies with part 15 of the FCC rules. Operation is subject to the
following
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, Including interference
that may cause undesired operation.
Federal Communications Commission Requirements. The equipment has been
tested and found to comply with the limits for Class B Digital Device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction, may cause harmful
interfernce to radio communication. However, there is no guarantee that
interference will not occur in a particular installatin.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turnung the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures :
˙Reorient of relocate the receiving antenna.
˙Increase the separation between the equipment and receiver.
˙Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
The changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
(a) When battery is running out of electric capacity. LED will
start flashing in order to indicate user that the capacity is
empty.
(1) Mouse
(2) Keyboard
(b) Power Switch :
(1) You can turn ON / OFF the power of Mouse by this
power swith as you want to extend the batteries' life.
A)
Turn ON the computer.
Connect the receiver to the PC via USB port.
B) ID Select Important :
ID connect for Keyboard & Mouse
Plug-in the receiver. the LED on receiver will flash for 30
seconds. Press ID button on Keyboard or Mouse within
30 seconds. When ID matched, the LED will stop
flashing. Then the Device could work.
(a) Keyboard
(b) Mouse
(1) Keyboard
(2) Mouse (3) Receiver (4) Battery
Specification :
(1) Input Voltage : DC 3V(min).
(2) Power Consumption : Keyboard : 3 mA (max),
Mouse : 16 mA (max).
(3) Available Distance : 10 m(max).
(4) Characters per Inch : 1000 CPI.
(5) Wireless RF : 2.4 GHz.
(6) System Requirements : Windows 7 / Vista / XP / 2000.
Troubleshooting :
Specification :
(1) Input Voltage : DC 3V(min).
(2) Power Consumption : Keyboard : 3 mA (max),
Mouse : 8 mA (max).
(3) Available Distance : 10 m(max).
(4) Characters per Inch : 1000 CPI.
(5) Wireless RF : 2.4 GHz.
(6) System Requirements : Windows 7 / Vista / XP / 2000.
1.5V / AAAx2
1.5V / AAAx2
1.5V / AAAx2
ID Connect Button
PC
ID Connect button
OFF
ON