215 SA active subwoofer
15 SA Il lampo con la freccia inserito in un triangolo equilatero avvisa l'utilizzatore della presenza di tensione pericolosa, senza isolamento, all'interno dell'apparecchio che potrebbe essere sufficientemente alta da generare il rischio di scossa elettrica. Il punto esclamativo inserito in un triangolo equilatero avvisa l'utilizzatore della presenza di importanti istruzioni per l'utilizzo e per la manutenzione.
215 SA Introduzione Subwoofer attivo ■ amplificatore a MosFet da 800 W RMS ■ processore ■ crossover elettronico stereo (24dB/oct) Il subwoofer attivo 215SA è il complemento ideale del sistema W20A per il rinforzo della gamma grave. Grazie all'elettronica incorporata, 215SA è abbinabile a sistemi di altoparlanti di ogni tipo e marca. I due woofer da 15" offrono prestazioni decisamente interessanti in un ingombro particolarmente contenuto.
215 SA Pannello controlli e connessioni 1 2 6 Montarbo MOD. 215 SA POWER POWERED PROCESSOR CONTROLLED STEREO SUBWOOFER SYSTEM 800W 100Hz 20KHz 4 GND 7 FLAT LIFT L L LINK L INPUT X-OVER OUT 4 5 6 2 8 1 3 R R / mono 9 0 10 INPUT LEVEL R 8 7 3 FUSE F 5A 5 1 Selettore Flat / X-Over. Consente di inviare alle casse acustiche "satellite", collegate all'uscita stereo (2), il segnale a larga banda o solo la gamma alta.
215 SA Esempi di collegamento L’omnidirezionalità delle bassissime frequenze riprodotte dal mod. 215SA (37÷100 Hz) rende l’installazione del subwoofer per nulla critica. Pur se è sempre preferibile posizionare il subwoofer vicino alle casse acustiche, quando necessità di spazio o praticità di montaggio lo richiedano il subwoofer può essere montato anche a distanza dalle casse stesse (ad esempio: sotto il palco).
215 SA NOTA: Se disponete di un mixer amplificato provvisto di inserzioni, e volete utilizzare il subwoofer senza escludere le uscite di potenza, potete prelevare il segnale dalle stesse prese insert mediante jack stereo, nei quali avrete precedentemente CABLARE LA SPINA JACK STEREO COME ILLUSTRATO collegato l'anella (RING) con la punta (TIP) cortocircuitandole, ed inviarlo agli ingressi del subwoofer mediante XLR sbilanciati.
215 SA Importante ! Cura e manutenzione del prodotto: • Posizionare la cassa lontano da fonti di calore (caloriferi o qualsiasi altro oggetto che produca calore). • Evitare di esporre la cassa alla irradiazione solare diretta, ad eccessive vibrazioni e ad urti violenti. • Evitare l'uso e il deposito in ambienti polverosi o umidi: eviterete così cattivi funzionamenti e deterioramento anticipato delle prestazioni.
215 SA The lighting flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated 'dangerous voltage' within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to humans. The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions.
215 SA Introduction Active subwoofer ■ 800 W MosFet power amplifier ■ processor ■ stereo electronic crossover (24dB/oct) Montarbo 215SA active subwoofer was designed to extend the low frequency response of the W20A system. But at the very first test, it proved to be the perfect companion for loudspeakers of any make and model. The two 15" units of the 215SA combine performance with significant space savings, a key feature to many pro users. solid 215SA absolutely don’t flex. Period.
215 SA Control and connection panel 1 2 6 Montarbo MOD. 215 SA POWER POWERED PROCESSOR CONTROLLED STEREO SUBWOOFER SYSTEM 800W 100Hz 20KHz 4 GND 7 FLAT LIFT L L LINK L INPUT X-OVER OUT 4 5 6 2 8 1 3 R R / mono 9 0 10 INPUT LEVEL R 8 7 3 FUSE F 5A 5 1 Flat / X-over switch allowing the "satellite" speaker systems, connected to the stereo output (2), to receive a full-range signal or the upper audio range only.
215 SA Connection examples The very low frequency range reproduced by the subwoofer model 215SA (37÷100 Hz) is essentially omnidirectional allowing easy installation of the enclosure. In most cases the subwoofer can be placed near to the loudspeaker system, but when space or set up reason dictate it, the subwoofer can be positioned at some distance from the speaker system (e.g.: under the stage floor).
215 SA Connection examples NOTE: Our configuration examples are using the L and R master outputs of the mixer, but if they are already taken up (as, for example, in a powered mixer) the insert sockets can be used to the same purposes. WIRE THE STEREO JACK PLUG AS SHOWN Take out the signal from the insert sockets by means of a stereo jack plug, in which you have previously joined the RING with the TIP and send it to the inputs of the subwoofer by means of an unbalanced XLR.
215 SA Important ! Product Care and Maintenance: Power supply connection: • Never expose the enclosure to heat sources such as radiators or other products that produce heat. • make sure the mains power switch is off ('0') before starting any connection. • Never expose the enclosure to direct sunlight, excessive vibrations or mechanical shocks. • check that mains voltage corresponds to the voltage indicated on the panel. • always connect the power cord to a grounded outlet.
215 SA APPENDIX 15 Specifications __________________________________________ 16 Block diagram __________________________________________ __________________________________________ 17 Connectors __________________________________________ 18 Connection example A __________________________________________ 19 Connection example B __________________________________________ 20 Connection example C __________________________________________ 21 Parallel Connection __________________________________________ 22 Spar
215 SA Specifications Speaker System bass-reflex • Power Handling 1000W • Impedance 4Ω • Frequency Response 37Hz ÷ 100Hz • Sensitivity (1W, 1m) 102 dB • Max. S P L: 130 dB • Built-in electronic crossover: Crossover frequency Slope • Components: Nominal diameter Frequency range Power capacity Sensitivity Rated impedance Net weight THIELE/SMALL PARAMETERS fs Re Qms Qes Qts Vas ηo B.l SD Xmax Pe 100Hz 24dB/octave 2 x 15" WOOFER MOD.
215 SA Block diagram APPENDIX 16
215 SA Connectors 1 GND Ground 2+ Hot 3Cold (standard IEC 268) 2 3 BALANCED XLR MALE CONNECTOR 1 ▲ BALANCED XLR FEMALE SOCKETS Montarbo ▲ MOD.
215 SA Connection example A: one 215SA + two W20A active systems mixer L / R outputs ➟ 215SA L / R inputs 215SA L / R outputs ➟ W20A inputs W20A W20A Montarbo POWER SERIAL N. 5 6 4 7 2 OUT OUT LINK 10K IN LINK IN 0,775V RMS 9 0 FUSE F 6,3 A 215SA GND CAUTION : TO PREVENT RISK OF FIRE ALWAYS REPLACE FUSES WITH SAME TYPE AND RATINGS. 220V POWER CONSUMPTION 1600W 50/60Hz 600+250W RMS 5 6 10 VOL. 7 LIFT MOD. 215 SA LINK IN LINK 10K IN 0,775V RMS 4 5 6 0 10 H.F.
215 SA Connection example B: two 215SA + two W20A active systems mixer L / R outputs ➟ 215SA 'R/MONO' inputs 215SA 'R' outputs ➟ W20A inputs W20A W20A Montarbo MOD. POWER 1 OUT OUT LINK LINK 10K IN 9 0 IN 0,775V RMS 9 0 FUSE F 6,3 A 215 SA 220V POWER CONSUMPTION 1600W 50/60Hz LIFT 0 POWER Montarbo 800W RMS SERIAL N.
215 SA Connection example C: one 215SA + two W20A active systems mixer 'AUX' output ➟ 215SA 'R/MONO' input mixer 'L' output ➟ W20A input mixer 'L' output ➟ W20A input W20A W20A Montarbo MOD. POWER 5 6 4 7 1 OUT OUT LINK 10K IN LINK 0,775V RMS 9 0 FUSE F 6,3 A 215SA GND CAUTION : TO PREVENT RISK OF FIRE ALWAYS REPLACE FUSES WITH SAME TYPE AND RATINGS. 220V POWER CONSUMPTION 1600W 50/60Hz 600+250W RMS 5 6 10 VOL. 7 LIFT MOD.
5 SA Parallel connection of two or more systems mixer L / R outputs ➟ 215SA 'R/MONO' inputs 215SA 'LINK' outputs ➟ 215SA inputs Montarbo MOD. 215 SA Montarbo 800W POWER POWERED PROCESSOR CONTROLLED STEREO SUBWOOFER SYSTEM 100Hz 20KHz 215 SA MOD. 800W POWER POWERED PROCESSOR CONTROLLED STEREO SUBWOOFER SYSTEM 100Hz 20KHz GND FLAT GND FLAT LIFT L L LINK LIFT L INPUT L X-OVER OUT L L LINK INPUT X-OVER OUT 4 5 6 2 9 R R 230V 50/60Hz FUSE F 5A Montarbo MOD.
215 SA Spare parts B010010 A300151 D522151 A088677 A088676 B021102 D202152 B005010 D00119F A300151 D521190 D52118T STAND HOLDER B010010 WOOFER 15" PK40 8 Ω A300151 CONTROL & CONNECTION PANEL D522151 AMPLIFIER CHASSIS: D521190 POWER AMPLIFIER HEAT SINK D52118T POWER AMPLIFIER D00119F POWER TRANSFORMER B005010 HANDLE ASSEMBLY A088676 A088677 B021102 FUSE 5A A600050 FUSE 10A A600100 METAL GRID D202152 APPENDIX 22
elettronica Montarbo srl via G. di Vittorio 13 40057 Cadriano di Granarolo Bologna, Italy Tel. +39. 051. 76 64 37 Fax. +39. 051. 76 52 26 E-mail: mail@montarbo.com Internet: www.montarbo.com Le informazioni contenute in questo manuale sono state attentamente redatte e controllate. Tuttavia non si assume alcuna responsabilità per eventuali inesattezze. Questo manuale non può contenere una risposta a tutti i singoli problemi che possono presentarsi durante l'installazione e l'uso dell'apparecchio.