BooSteam ste r EZ1 MONSTER FLOOR STEAMER INSTRUCTION MANUAL Model #: EZ1 AUS, NZ
SAVE THESE INSTRUCTIONS I M PO R TAN T SAF E 2 SAFETY WARNING • The manufacturer reserves the right to make changes to the design and features of the appliance without notice. • This appliance is solely for household use. • Do not turn the appliance on if the steam mop shows signs of damage, the power cable is damaged or if the appliance has been potentially subject to non-identifiable damage (e.g. the appliance as been dropped, etc.).
E T Y I N S TR U C T I O N S Customer Support Centre: Australia: 1800 663 866 New Zealand: 0800 666 783 Dispose of plastic packaging appropriately, as it may represent a potential hazard for children! IMPORTANT: Before operating the unit for the first time, read these instructions carefully and keep them for future reference. Euroflex relieves itself of any liability for damages that shall be the result of improper use of the appliance, not in conformity with what’s written in this instruction manual.
Product Features One (1) Floor Steamer 1 - Cord Winder 2 - Handle 3 - Metal Extension Tube 4 - Measuring Cup (pre-marked) 5 - Boiler Cap 6 - Steam Ready Indicator Light (green) 7 - Power Indicator Light (orange) 8 - Power Cord 9 - Steam Nozzles 10 - Hard Surface Floor Pad 11 - Carpet Floor Pad 12 - Carpet Glide 13 - Parking Pad 2 1 3 4 Technical Data Adapter Input: 220-240V~, 50/60Hz Cord Length: 7 meters/23 feet Power: 1200 watts Boiler: Stainless Steel Boiler Capacity: 0.
Assembly of Parts & Preparation of Steamer Make sure all parts are in the box (see pg 4). IMPORTANT: FOLLOW THESE INSTRUCTIONS CAREFULLY! A. Assemble Handle Before Use 1 After removing Handle Assembly from carton: • Pull Extension Tube apart (shown below). Pull apart Extension Tube • Extend Tube to the “Lock - I” position. LOCK K! CLIC • Snap connector down. When a “click” is heard, the Tube is locked in position.
Before Use B. Attach Handle to Steamer • Before starting, remove the self-tapping screw from the bottom of Extension Tube. • Insert the Handle Assembly into the Floor Steamer Base. Align Arrow on Handle with Arrow on Base (as shown in Fig. A). • Once inserted, twist Handle Assembly 90° clockwise (as shown in Fig. B). Be sure Arrow on the Handle is aligned with Line/Lock Icon on Base. Fig. B Fig. A 90° Front View Side View Fig.
Affix either the Hard Surface Floor Pad or Carpet Glide with Carpet Pad to your Floor Steamer. WARNING: To prevent floor damage, ALWAYS attach either the HARD SURFACE FLOOR PAD or the CARPET GLIDE ACCESSORY with CARPET PAD when using your Floor Steamer. NEVER use without either of these attachments affixed to the machine. Before Use C. Attach Hard Surface Floor or Carpet Pad to Steamer ATTACHING HARD SURFACE FLOOR PAD Place Floor Pad face down on the floor, with white hook and loop strips facing up.
Before Use D. Filling Boiler with Water WARNINGS: • Carefully read all instructions before removing Boiler Cap. • Always unplug appliance before filling the Boiler. *IMPORTANT* Use tap water – distilled or demineralized water is recommended if tap water is too hard. DO NOT add detergents, perfumes, oils or other chemical substances. Follow these instructions to avoid overfilling the Boiler. • Be sure appliance is unplugged, and has cooled for at least 5 minutes before filling with water.
Using Your Floor Steamer A. Using the Parking Pad You can use the Parking Pad if the Steamer is warm or hot. CAUTION The Parking Pad is provided to prevent floor damage that can result from leaving a hot steamer resting on the same spot for too long. ALWAYS place Floor Steamer on the Parking Pad when not in use, or while it is cooling before storage. Using Your Floor Steamer D G RK IN PA PA 2 B. Starting the Appliance • Be sure Boiler is filled with water and Boiler Cap is securely in place.
Using Your Floor Steamer C. Using Steam (continued) • To emit steam from the Steam Nozzles, push the trigger on the Handle. *IMPORTANT* The Steam Nozzles are meant to be used in steam “bursts” and should never be used on a sustained basis. The Steam Nozzles will loosen especially difficult debris and will assist in cleaning hard to reach areas such as floor edges. NOTE: Your Steamer will not need the Boiler to be refilled for up to 20-25 minutes.
Cleaning and Rinsing Floor Steamer If distilled or demineralized water is regularly used there is no need to clean the Boiler. Rinsing the Boiler We recommend you periodically rinse the Floor Steamer to prevent the accumulation of calcium and sediment caused by hard water use. After 10 - 15 refills, fill the Boiler 3/4 full with hot tap water, shake several times and empty out into sink or bathtub. Wipe the Steamer base with a damp cloth and wipe dry. NEVER HOLD THE STEAMER UNDER TAP TO FILL.
Troubleshooting Issues Possible Causes Solutions Steam is not coming out of the Improper Handle assembly. Steam Nozzles. Call Customer Service to receive instructions to correct the problem. The Hard Surface Floor Pad is not adhering to Steamer. Position Steamer about 2” above Pad and FIRMLY press it down onto the Pad. Not enough pressure was applied when attaching Pad. The Cleaning Pads are getting Boiler is overfilled. soaked (too wet). Why? Let Steamer run until excess water ceases.