Soundstage 3 Portable Speaker P/N 43666 User's Manual
SAFETY WARNINGS AND GUIDELINES Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference. • This device is intended for indoor use only. • Do not expose this device to water or moisture of any kind. Do not place drinks or other containers with moisture on or near the device.
• Take care to prevent damage to the power cord. Do not allow it to become crimped, pinched, walked on, or become tangled with other cords. Ensure that the power cord does not present a tripping hazard. • Never unplug the unit by pulling on the power cord. Always grasp the connector head or adapter body. • Ensure that power is turned off and disconnected before making any electrical connections. • This device contains a Lithium battery.
PACKAGE CONTENTS Please take an inventory of the package contents to ensure you have all the items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement. 1x Soundstage 3 Portable Speaker 1x 3.5mm Audio Cable 1x AC Power Cord 1x User's Manual PRODUCT OVERVIEW Front Panel 1. Tweeters: Two 1" silk dome tweeters. 2. Woofer: One 5.25" concave aluminum cone woofer.
Top Panel 3. ON/STANDBY: Press the button to power the speaker on or to put it into standby mode. 4. BATTERY: The 4 LEDs illuminate to indicate the charge level of the internal battery. 5. PAIR: Press the button to put the speaker into Bluetooth® pairing mode. 6. VOLUME▬: Press the button to decrease the volume level. 7. VOLUME✚: Press the button to increase the volume level. 8. SOURCE INDICATORS: One of the LEDs illuminates to indicate the selected input. 9.
3. AUX IN: 3.5mm stereo analog input. 4. RCA IN: Stereo analog RCA input. 5. SUB OUT: Mono analog RCA jack for connecting an external subwoofer (available separately). 6. USB POWER: USB charging port with 5 VDC, 2A output for charging mobile devices. 7. AC INPUT: Unpolarized IEC 60320 C8 input for connecting the included AC Power Cord. 8. POWER: Master power switch for turning the speaker on or off. INSTALLATION Perform the following steps to install the Soundstage 3 speaker.
. Plug one end of the included AC Power Cord into the AC INPUT on the rear panel, then plug the other end into a nearby AC power outlet. 8. Place the POWER switch on the rear panel in the ON position. This puts the speaker into standby mode. 9. Press the ON/STANDBY button on the top panel to turn the speaker on. CHARGING This speaker contains an internal Lithium battery.
SPECIFICATIONS P/N 43666 Supported Audio Channels 2.1 Amplifier Type Digital Class D Amplifier Frequency Response 42Hz ~ 20kHz Crossover Frequency 3.0kHz Woofer Driver 1x 5.25" concave aluminum cone Tweeter Drivers 2x 1" silk dome Low Frequency Amplifier Power 1x 30 watts High Frequency Amplifier Power 2x 10 watts 3.5mm stereo analog, RCA stereo analog, Inputs digital optical S/PDIF, Bluetooth® Outputs Mono analog subwoofer, USB power Bluetooth® Version 4.
TECHNICAL SUPPORT Monoprice™ is pleased to provide free, live, online technical support to assist you with any questions you may have about installation, setup, troubleshooting, or product recommendations. If you ever need assistance with your new product, please come online to talk to one of our friendly and knowledgeable Tech Support Associates. Technical support is available through the online chat button on our website www.monoprice.com or through email by sending a message to tech@monoprice.com.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Radio Notice for FCC Caution This FCC Part 15 radio device operates on a non-interference basis with other devices operating at this frequency.
