The technical data may be changed without prior notice SMART HOME MUSIC SYSTEM M - + USER MANUAL Address: No.1 Xiahe Rd,Jianggao , Baiyun,Guangzhou , China Post Code:510450 Tel:+86-20-37166501 Website:www.dsppatech.com Guangzhou DSPPA Audio Co., Ltd.
Packing List Component Smart music amplifier Quantity 1 Box 1 Remote control 1 Ceiling loudspeakers 2 User manual 1 Guangzhou DSPPA Audio Co.
Contents Directivity curves Introduction 1 Profile of product 1 Smart music amplifier 1 Ceiling loudspeaker 1 Product Information 2 Smart music amplifier basic functions M1 Vertical directivity pattern M2 Vertical directivity pattern M1 Horizontal directivity pattern M2 Horizontal directivity pattern Descriptions of music controller 3 On & Off, Standby 3 Smart music amplifier play function 4 System settings 5 Descriptions of remote controller 6 Installation and wired 7 Ceiling l
Introduction Thanks for using our products. All our products are tested strictly before leaving the factory, with guaranteed quality. For better installation, commissioning and use of the product, please read this manual in detail before installation. Frequency response and distortion characteristic s M1 frequency response characteristics (dB SPL、1W、1m) M1 distortion characteristic (THD< 1.5% 1W、1m、100Hz-10kHz) 100 5.00 90 4.00 80 3.
Technical parameters Production Information Smart music amplifier Technical index Power input Model ~100-240V 2 ×10W Output power 8Ω Rated impedance Smart music amplifier ≤0.03% (1KHz, 1W, 8Ω) Total harmonic distortion Signal-to-noise ratio >81dB Frequency response 20Hz – 20KHz Sensitivity of auxiliary AUX:1.0V/500mV input (adjustable) Sensitivity of auxiliary AUX:0-1.0V output (adjustable) Audio format MP3 , WAV, FLAC,etc.
Smart music amplifier basic functions ● Concealed installation Note: you buy the box depth of not less than 40mm. Descriptions of music controller ① Open a groove suitable for the box dimension on the wall needing installation, and based on the positions of screw holes at the four corners of the bottom surface of the box, drill holes on the wall groove, and prepare to connect lines.
③ As show in the following figure, Select the two clips in the direction of A or B, outer open edge outward, so snap out of and be careful to separate the amplifier front panel and the base. Base A B Front panel Smart music amplifier play function 1.FM Press “M” key to choose FM mode. Automatic Search: long press “ ” to start the automatic channel receiving, and the system will automatically save the effective radio stations.
Functions of connection terminals 5.AUX OUT This device can be used as a audio source output to other amplifier devices. when the AUX OUT interface is connected with other devices and the FM\USB\SD\AUX IN\ Bluetooth is selected for playback, the audio signal can be output to these devices to play synchronously. Function Power input - + AUX OUT Power amplifier output 8 Ω GND Symbol Name 6. Bluetooth connection Press “M” key to choose BT mode.
③ Device maximum volume limit setting. allow users to set the maximum volume size of a device, there are 25%, 50%, 75%, 100% four options , to select one and click “Configure” to complete the modification. Descriptions of remote controller 2 5. Finally , check the installation is secure . Smart music amplifier wired 1 3 4 5 6 7 8 FM AUX IN AUX OUT SPEAKER 8Ω OUTR- OUTR+ L OUTL- OUTL+ L R R ANT GND ~100-240V 1.Standby switch. 2. Mode selection.
Installation and wired 2. Connect the audio broadcast transmission line. and select the proper terminal for connection according to the actual power needs. Ceiling loudspeakers installation The size of the Space that best sound playback : 50m² (Including 2 speakers) . Signal line Red line---Positive electrode The wall distance of not less than1000mm The wall distance of not less than1000mm Blue line ---Negative pole Not less than 2000-3000mm Ceiling loudspeaker 3.
Warning Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.