Installation Instructions Monogram Drawer Microwave For Models: ZWL1126SJ 49-40754-2 (01-18 GEA)
Installation Instructions Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com BEFORE YOU BEGIN WARNING Stepping, leaning or sitting on the drawer may result in serious injuries and can also cause damage to the Drawer Microwave. Read these instructions completely and carefully. IMPORTANT — Save these instructions • Do not use the Drawer Microwave as a storage space. This creates a potentially hazardous situation. • Check that the time-of-day is in the display.
Installation Instructions CLEARANCES AND DIMENSIONS 24” DRAWER MICROWAVE MEASUREMENTS (Continues) •D imensions that are shown in Figure 1 (for 24”) must be used. Given dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See Figure 4. •C ontact surface must be solid and level. Pay special attention to the floor on which the Drawer Microwave will sit.
Installation Instructions ANTI-TIP BLOCK GROUNDING INSTRUCTIONS NORMAL INSTALLATION STEPS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
Installation Instructions 24” Flush Mount Deflector Vent IMPORTANT NOTES TO THE INSTALLER PARTS INCLUDED •R ead all of the Installation Manual that is included with the Drawer Microwave before installing in the flush mount configuration. •O bserve all governing codes, ordinances, and safety instructions. •B e sure to leave this installation with the consumer. Qty Description 1 Flush Mount Deflector Vent 2 Mounting Screws 1. Prepare cabinet opening as shown in Figures 6, 7, 8, and 9.
Installation Instructions 24” Flush Mount Deflector Vent 1. Prepare cabinet opening as shown in Figures 6, 7, 8, and 9. Anti-Tip Block Mounting Cleat Drawer Face / ” 1 3/16” 1 8 Cabinet Face 22” mounting cleat opening width Figure 7 NOTE: the mounting surface of the finished cleat must sit 1 3/16” back from the face of the cabinet (pushing the face of the drawer out 1/8”). CL Top View Move oven location downward for extended countertops for better viewing angle.
Installation Instructions 24” Flush Mount Deflector Vent 2. Install deflector as shown in Figures 10 and 11 6. Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16” bit. See Figure 12. Shelf detail showing the deflector vent during installation. Position deflector vent and mark holes. Pre drill using a 1/16” bit before mounting. Figure 10 Figure 12 Shelf detail showing the deflector vent installed. Mounting Flange 7.
Notes TINSLB048MRR0l 8
Instrucciones de Instalación Monogram Drawer Microwave Modelo: ZWL1126SJ 49-40754-2 (01-18 GEA)
Instrucciones de Instalación ¿Preguntas? Llame al 800.GE.CARES (800.432.2737) o visite nuestro sitio web en: GEAppliances.com ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. IMPORTANTE — Conserve estas instrucciones para uso del inspector local IMPORTANTE — Cumpla con todos los códigos y ordenanzas gubernamentales. •N ota para el Instalador — Asegúrese de que el Comprador conserve estas instrucciones.
Instrucciones de Instalación DESPEJES Y DIMENSIONES MEDIDAS DEL MICROONDAS DE CAJÓN DE 24” (Continúa) •D eben ser usadas las dimensiones que se muestran en la Figura 1 (para 24”). Las dimensiones dadas proveen un despeje mínimo. Ubique el tomacorriente en el área sombreada en la esquina superior izquierda de la abertura. Ver figura 4. •L a superficie de contacto debe ser sólida y estar nivelada. Preste especial atención al piso en el cual el Microondas de Cajón se apoyará.
Instrucciones de Instalación BLOQUE ANTI-VOLCADURAS INSTRUCCIONES DE CONEXIÓN A TIERRA PASOS PARA UNA INSTALACIÓN NORMAL Instrucciones de Instalación del BLOQUE Antivolcaduras Este electrodoméstico deberá estar conectado a tierra. En caso de que se produzca un cortocircuito, la conexión a tierra reduce el riesgo de descarga eléctrica, brindando un cable de escape de la corriente eléctrica.
Instrucciones de Instalación Ventilación con Deflector con Montaje al Ras de 24” NOTAS IMPORTANTES PARA EL INSTALADOR PIEZAS INCLUIDAS •L ea todo el Manual de Instalación incluido con el Microondas de Cajón, antes de instalar la configuración del montaje al ras. •C umpla con todos los códigos, ordenanzas e instrucciones de seguridad. •A segúrese de que estas instrucciones queden en manos del comprador. Cant Descripción 1 Ventilación con Deflector con Montaje al Ras 2 Tornillos de Montaje 1.
Instrucciones de Instalación Ventilación con Deflector con Montaje al Ras de 24” 1. Prepare la abertura del gabinete como se muestra en las Figuras 6, 7, 8 y 9. Bloque Antivolcaduras Taco de Montaje Cara del Cajón Ancho de la abertura del taco de montaje de 22” Figura 7 NOTA: La superficie de montaje del taco terminado se debe apoyar en 1 3/16” sobre la cara del gabinete (empujando la cara del cajón hacia fuera 1/8”).
Instrucciones de Instalación Ventilación con Deflector con Montaje al Ras de 24” 2. Instale el deflector como se muestra en las Figuras 10 y 11. 6. Abra el cajón. Utilizando los 4 agujeros del cajón como una plantilla, marque el gabinete usando una broca de 1/16”. Ver figura 12. Detalle de la repisa donde se muestra la ventilación del deflector durante la instalación. Posicione la ventilación del deflector y marque los agujeros. Realice marcas usando una broca de 1/16” antes de realizar el montaje.
Notas TINSLB048MRR0l 8