Instruction Manual

ManualsBrandsMOES ManualsElectronicsSmart Switch

200MM

520MM

65MM

正面

反面

正面

200X455MM 四色印刷

80g哑光纸风琴折

Instruction Manual

Smart Switch

Wi-Fi Single Pole / 3 Way

Scan the QR code

Please connect the device

according to the

conﬁguration process.

1. Method one:

2. Method two:

Scan the QR code to conﬁgure the network guide.

HOME, SMART MOES HOME

English

① ②

Line/Load

Neutral

Line/Load

Neutral

Line/Load

Neutral

Line/Load

Neutral

Line/Load

Neutral

BH19

Thank you for your support and purchase at we Moes,we

are always here for your complete satisfaction,just feel

free to share your great shopping experience with us.

If you have any other need,please do not hesitate to

Locate your circuit breaker panel and turn oﬀ the power

to each switch you are replacing.

Remove the switch and pull it away from the wall.

STEP 2

STEP 1

Circuit breaker panel

Turn Oﬀ Power

Input Power:

Control Principle :

Wireless Protocol:

Max Current:

Standby Power:

Button Life:

100~245V AC 50/60Hz

Model: WS-SR-US-T

Relay

WiFi 802.11 b/g/n 2.4GHz

10A

≤0.5W

500K times

106*45*35 mmDimension:

STEP 5

STEP 7

STEP 10

ON/OFF

LED Indicator

Cover Panel

Switch Status

Light StatusLight Color

White

OFF

Power OFF

Power ON

Blink Quickly

(0.5s )

Blink Slowly

(1s )

Ready for AP

(Access Point)

conﬁguration mode

Ready for default

conﬁguration mode

Tools you’ll need

Flat-head screwdriver

Phillips-head screwdriver Pliers

Electricity can cause personal injury and property damage

if handled improperly.If you are not sure about any part of

these instructions, please seek professional assistance

from a qualiﬁed electrician.

Ensure all wark meets applicable local and national codes.

WARNING: RISK OF ELECTRIC SHOCK

Voltage tester

Approximately

30 minutes to install

and setup the switch

30min

STEP 3

STEP 4

Verify Power is Oﬀ

Pull Out Old Switch

You may need to turn oﬀ more than one circuit breaker.

We recommend you to remove the faceplate from the old switch

and use an electrical tester to test all wires connected to the

switch to ensure there is no voltage in the circuit.

STEP 6

STEP 9

Mount the switch

STEP 11

STEP 12

Turn on the power

3.Open Smart Life/Tuya App and Click“+”,then the

prompt page will automatically show on the screen.Click

“Go to add”.

Pair and clear up the WiFi code with Bluetooth and WiFi

connected meantime.(New Updated)

2.Make sure your phone is connected to Wi-Fi and Bluetooth.

1.Press and hold switch button for 6s until the white

indicator ﬂashes to reset the switch and get into quick

conﬁgure mode.

Complete the wiring of the switch module before pairing

Complete the device's networking conﬁguration

according to the prompts in the App.

STEP 1

If you have already conﬁgured Google Home, you

can skip this step. The following instructions are

based on the iOS client.

STEP 2

Control the device via voice commands, now you

can control your smart device with Google Home.

You can control your device (such as your bedroom

light) with the following commands:

STEP 4

Key step —— Link Skill

STEP 3

Tap on "Skills" in the Alexa App menu.

Make sure you Google Home device is powered on and

connected to a Wi-Fi network.

Open the Google Home App on your phone. After

successful login, tap on the menu in the upper left corner

and select “SET UP” to set up Google Home.

It will notify you with a sound to ensure that you are

connected to the correct device. After you hear the

sound, tap “YES” to proceed to the next step.

You can choose to diﬀerentiate the room where Google

Home is located from other Google devices. Then,

select the Wi-Fi network and language, wait for the

system to complete the conﬁguration, and tap “next”.

According to the page prompts, choose whether to

agree to the corresponding operation. When the page

displays “Google Home is ready,” select “continue” to

the next step.

Next is the voice control guide tutorial. Once you are

done listening, tap "FINISH SET UP". At this point,

Google Home setup is complete.

Ok Google, turn on/oﬀ bedroom light.

Ok Google, set bedroom light to 50 percent.

Ok Google, brighten bedroom light.

Ok Google, set bedroom light to red.

4.Select the device you want to add and click “+”

5.Enter Wi-Fi Password and click “Next”,waiting for

completing the connection.

Note:

The switch only supports 2.4G network.If you have connected

5G network,please disconnect 5G network ﬁrstly and connect

2.4G network.

STEP 3

Key step —— Link Skill

Complete the device's networking conﬁguration according

to the prompts in the App.

STEP 1

STEP 2

Control the device via voice commands, now you can

control your smart device with Echo. You can control

your device (such as your bedroom light) with the

following commands

STEP 4

Make sure you Amazon Echo device is powered on and

connected to a Wi-Fi network.

Enter the App account and password, then tap

“Link Now” to link your App account to enable the

Skill. Now you can start your smart home journey.

Open the Alexa App on your phone. After successful

Home page, select "Settings" and tap "Set Up A New

Device" to set up the Amazon Echo.

Choose your Amazon Echo device type and language

for connecting. Press and hold the small dot on the d

evice until the light turns yellow. Then tap “Continue”

to connect to the hotspot.

After connecting to the Amazon Echo hotspot, return to

the page. At this point, the connection is successful.

Tap “Continue” to proceed to the next step. Choose a

Wi-Fi network to connect to. Amazon Echo will take a

few minutes to try to connect to the network.

After the network connection is successful, tap

“Continue”. An introduction video will appear. After the

video ends, tap “Continue” to jump to the Alexa Home

page. You have now completed the Amazon Echo's

conﬁguration process.

Then search for "App Name". Tap "Enable" to enable

the Skill.

On the main page of the Google Home App, tap the sidebar

menu in the top left corner and select “Home Control”.

Alexa, turn on/oﬀ bedroom light.

Alexa, set bedroom light to 50 percent.

Alexa, brighten/dim bedroom light.

Alexa, set bedroom light to green.

Then tap the plus sign in the lower right corner and search

for “App Name”.

Find App Name on the list and open it, select the country

where your App account is located, enter your App

account and a password, and tap “Link Now”.

6.Add the device successfully, you can edit the name of the

device to enter the device page by click “Done”

If you cannot add your Smart Device , please check:

1) Whether the Smart Device is powered on.

2) Whether the phone is connected with 2.4GHz Wi-Fi

network.

3) Please check routers or related: if your router is

dual-band, please select 2.4GHz Wi-Fi network to connect

your phone and Smart Plug.

4) Setting up Wi-Fi router: setting encryption method as

WPA2-PSK and authorization type as AES, or set both

as auto. Wireless mode cannot be 11n only.

5) Please use English and numbers to name your Wi-Fi

router. Otherwise our Smart Plug may not recognize it

when you try to add it into Smart Life.

6) To stay strong Wi-Fi connection, please keep smart

device close to router.

7) Whether connected devices have reached the

maximum number of router’s connections. If so, please

turn oﬀ some devices connected to the router and try

again.

Please disconnect the power supply before installing or removing the

device for avoiding irreversible damage on the device from the

electric current or some unpredictable problems such as lamp

ﬂashing.

Attention:

All products marked with the symbol for separate

collection of waste electrical and electronic equipment

(WEEE Directive 2012/19 / EU) must be disposed of

separately from unsorted municipal waste.

To protect your health and the environment,

this equipment must be disposed of at

designated collection points for electrical

and electronic equipment designated by the

government or local authorities. Correct

disposal and recycling will help prevent

potential negative consequences for the environment and

human health. To ﬁnd out where these collection points

are and how they work, contact the installer or your local

authority.

Identify The Old Switch

3-Way 3-Way

Single Pole Switch

3-Way Switch

Single Pole

Two switches control the same light or the same bundle of lights.

Only one switch control one light or a bundle of lights.

Single Pole Switch

ldentify Line/Load Wire

Note:The color of your wire may be diﬀerent from

the color shown on the manual.

3-Way Switch

LINE/LOAD wire (usually BLACK, attached with a black screw, and

may be Remarked "common".)

Line /Hot

Traveler

Line /Hot

Load

Traveler

Find the NEUTRAL Wires

Neutral wire is required to install the smart light switch.Most likely

a bundle of one or more white wires in the wall.

Test NEUTRAL and GROUND Wires

Make sure there is no power on the neutral wires from neighbor-

ingcircuit. lf necessary, shut oﬀ additional circuits until no voltage

is found.

GROUND wires are usually BARE COPPER or GREEN.

STEP 8

Neutral

Ground

Traveler

Line /Hot

Note: If there is no neutral, please try another

location or call an electrician for help.

Neutral

Take Pictures of the Wiring

Loosen the screw terminals and remove

the old switch.

Wire the Smart Switch

Single Pole Wiring Diagram

( 3-Way Model）

Neutral（White）

N L

Line /Hot（Black)

Ground

（Green）

3-way Smart Switch

Cap oﬀ the remaining L2 wire (RED) from the

Switch with a wire nut.

Common

Neutral（White）

Line /Hot（Black)

Traveler

N L

Traditional

Switch

Smart

Switch

Ground

（Green）

3-way Smart Switch

3-Way Wiring Diagram

Replace ONE of your REGULAR

3-WAY SWITCHES with SMART

SWITCH

Traditional

Switch

Smart

Switch

Common

Line /Hot（Black)

Ground

（Green）

Traveler

Neutral（White）

3-way Smart Switch

3-Way Wiring Diagram

N L

Neutral（White）

Ground

（Green）

Line /Hot（Black)

Smart

Switch

Smart

Switch

Ground

（Green）

Traveler

Replace BOTH of your REGULAR

3-WAY SWITCHES with SMART

SWITCHES

Not Working Situation

Traditonal Dimmer

Smart Dimmer

Smart

Switch

② Registration or Log in.

• Download “MOES” Application.

• Enter the Register/Login interface; tap “Register” to

create an account by entering your phone number to get

veriﬁcation code and “Set password”. Choose “Log in” if

you already have a MOES account.

③ Conﬁgure the APP to the switch.

• Preparation: Ensure the switch has been connected with

electricity; ensure your phone has been connected to

Wi-Fi and is able to connect to the Internet.

① Download MOES App on App store or scan

the QR code

MOES App is upgraded as much more compatibility

than Tuya Smart/Smart Life App, functional well for

scene controlled by Siri, widget and scene recommen-

dations as the fully new customized service.

(

Note: Tuya Smart/Smart Life App still works, but

MOES App is highly recommended)

1.During the free warranty period, if the product breaks

down during normal use, we will oﬀer free maintenance

for the product.

2.Natural disasters/man-made equipment failures,

disassembly and repair without the permission of our

company, no warranty card, products beyond the free

warranty period, etc., are not within the scope of free

warranty

3.Any commitment (oral or written) made by the third

party (including the dealer/service provider) to the user

beyond the warranty scope shall be executed by the third

party

4.Please keep this warranty card to ensure your rights

5.Our company may update or change the products

without notice. Please refer to the oﬃcial website for the

updates

MOES.Oﬃcial

@moes_smart

@moessmart

@moes_smart

www.moes.net

Bitte scannen Sie den QR-Code, um das deutsche

Handbuch, das Installationsvideo und die Funktion-

seinführung zu erhalten

Escanee el código QR para obtener el manual en

español, el video de instalación y la introducción de la

función

Veuillez scanner le code QR pour obtenir le manuel

en français, la vidéo d'installation et l'introduction des

fonctions

Отсканируйте QR-код, чтобы получить

руководство на русском языке, видео по установке

и описание функций

Leia o código QR para obter o manual em português,

o vídeo de instalação e a introdução das funções

请扫描二维码获取中文的说

明书、安装视频及功能介

If you have already conﬁgured Amazon Echo, you can

skip this step. The following instructions are based on the

iOS client.

01 Product Outline

05 Safety Information

06 Installation

10 Smart Life Skills (Google) SERVICE

RECYCLING INFORMATION

02 Indicator Light Status

03 Speciﬁcation

04 Contents Supplied

08 Wi-Fi link method:

(two pairing methods)

07 Add Devices

09 Smart Life Skills (Alexa)

11 FAQ

PanelSwitch Screws

Wire Caps

Warning:

Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s

authority to operate the equipment.

NOTE:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

PanelSwitch Screws

Wire Caps

Enter the App account and password, then tap “Link

Now" to link your App account. Choose the room where

your device is located, and then the skill will appear on

the Home Control Devices list. Now you can begin your

smart home journey.

8 10

19 21

FCC Statement:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC Radiation exposure limit set forth

for uncontrolled environment. This equipment should be installed

and operated with minimum distance 20cm between the radiator and

your body.