UNDERCABINET CD PLAYER with AM/FM Alarm Clock Radio and Bluetooth® Wireless Technology Owner's Manual PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
2
3
PREPARATION FOR USE Power Sources Main Unit: Unwind the AC power cord and extend it to its full length. Insert the AC plug of the cord into any convenient AC 120V~ 60Hz household outlet as the illustrated on right: NOTES: This unit is equipped with a polarized AC plug which has one blade wider than the other. This is a safety feature to reduce the likelihood of electric shock. This polarized AC plug will only fit in a polarized AC outlet.
Remote Control: In first time use, remove and discard the insulation film on the battery compartment as the illustrated follows: PAIR PAIR PULL PULL To replace the button cell if it is consume: 1. Push and slide out the battery tray as the illustrated below. 2. Replace the button cell by a new CR2025 button cell with the polarity “+” face up as the illustrated below and the marking on the rear of Remote Control. 3. Close the battery tray.
LOCATION OF CONTROLS Main Unit: 3 15 4 5 6 7 18 8 2 1 12 9 10 11 14 16 13 17 19 20 21 Remote Controls: 3 2 1 4 5 PAIR 6 10 7 8 9 12 11 PULL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
INSTALLATION Install the unit to the bottom of cabinet (if need) as follows: 2. Mount the Plastic Assemble Plate on the desired location as follows illustrated: 1. Detach the Plastic Assemble Plate from the top of unit by slide it to rear of unit as the illustrated: 3. Replace the unit to the mounted Plastic Assemble Plate as follows illustrated: CAUTION: To reduce the risk of fire, never mount the unit near any heat elements such like stoves; oven … etc.
OPERATION GENERAL OPERATION: 1. Connected the unit to AC power as instructed earlier. The Red Indicator will illuminate. 2. Press the Button on the unit or Remote Control to power on the unit from standby mode. The Red Indicator will not light and the LCD Display will illuminate. 3. Press the FUNCTION Button on the unit or Remote Control repeatedly to select the playback source. 4. Press the VOL +/- Buttons on the unit or the VOL DN/UP Buttons on the Remote Control to adjust volume level as desire. 5.
Notes: When the external BT Device searched the unit, our model number “CKR1307” will appear on the display of external BT Device. Pairing code “0000” or “1234” may need to enter. Normal operation after paired: 1. Turn on the BT function of the external BT Device. 2. Power on the unit and enter to BT mode as the instructed earlier. The indicator will appear on the display and blink. 3. Wait a few seconds until the unit auto paired to the external BT Device. (The indicator will stop blinking). 4.
4. Close the CD door by press the Button; the unit will start playback automatically. 5. During playback: A. Press the PAIR/ Button to pause; press again to resume normal playback. B. Press the or Buttons repeatedly to skip tracks. C. Press and hold the or Buttons to fast searching the specific section then release the button to resume normal playback. D. Press the DISPLAY Button to read the actual time. 6. To stop CD playback, press the ■ Button. The total number of tracks will appear on the display. 7.
RADIO: FM Band: 1. In standby mode, press the Button to power on the unit. 2. Press the FUNCTION Button repeatedly until “FM XX.X MHz” appear on the display. 3. Turn the TUNING Knob to receive the desired FM station. 4. To read the actual time during listening, press the DISPLAY Button once. Note: If the receiving FM station is stereo, the unit will auto plays it in stereo mode. AM Band: 1. In standby mode, press the Button to power on the unit. 2.
ALARM SET: 1. In power off (Standby) mode. Press and hold the ALARM Button on the unit or Remote Control approximate 2 seconds until indicator "TIMER" and alarm time appear on the display and the digit of hour of it is blinking. 2. Press the or Button on the unit or Remote Control repeatedly to set the Hour of alarm. (Make sure the PM Indicator appear on the display if the alarm time is PM and the AM Indicator is appear on the display if the alarm time is AM). 3.
CARE AND MAINTENANCE 13
TROUBLE SHOOTING GUIDE Symptom Possible Cause Solution Power Plug from AC Power Cord had not inserted to AC wall outlet. Insert the plug to wall outlet having AC 120V~, 60 Hz. Station not tuned properly. Retune the radio station. Noise or sound distorted on radio broadcasts The location not good for radio reception. Unwind the FM Antenna Wire on the rear of to full length and/or relocation it. No sound Volume at minimum. Increase Volume level by press the VOL + (VOL UP) Button.
GENERAL SPECIFICATIONS: Power Source: Clock back up: Audio Power: Impendence of Speakers: Radio Band Coverage: BT Version: BT Effective Range: AC 120V~, 60 Hz, 15W DC 4.5V, 3 x AAA size batteries; Not included 1.2 W (RMS) x 2 8 Ohm; 2W AM 520 - 1710 kHz FM 87.5 - 108 MHz 2.