AE-M EN 1.
Contents Safety instructions ................................................................................ 3 Introduction .......................................................................................... 5 Components ...................................................................................................................................... 5 Name and function of each part ......................................................................................................
Safety instructions Safety instructions Observe the following instructions to use the product safely and prevent any risk of injury or property damage. Warning Noncompliance of instructions could lead to serious injury or death. Installation Do not install the product in a place with direct sunlight, moisture, dust, or soot. A fire or electric shock may occur. Do not install the product in a place with heat from an electric heater. A fire or electric shock may occur due to overheating.
Safety instructions Operation Do not drop the product or apply an impact to the product. A product failure may occur. When cleaning the product, wipe the product with a soft and dry cloth and no water, benzene or alcohol. Otherwise, a product failure may occur.
Introduction Introduction Components AE-M Drilling Template Wall Bracket Diode Wall Fixing Screw x 2 Shrink Tube Ferrite Core Bracket Fixing Screw (Star Shaped) Quick Guide PVC Anchor x 2 NOTE Components may vary according to the installation environment.
Introduction Name and function of each part LED Indicator RF card authentication unit Reset button Cable Name Description LED Indicator Indicates the operational status of the device with the color of the LED.
Introduction Cables and connectors Pin Name Color 1 485 TRXP Blue (White stripe) 2 485 TRXN Yellow (Black stripe) 3 485 GND White (Black stripe) 4 ENET RXN Yellow 5 ENET RXP Black 6 ENET TXN Orange 7 ENET TXP White 8 ENET VB1 Red 9 ENET VB1 Green 10 ENET VB2 Blue 11 ENET VB2 Brown 12 WG GND Black 13 WG D1 White 14 WG D0 Green 15 TTL IN0 Purple 16 TTL IN1 Brown 17 TTL GND Gray 18 RLY NO Gray (White stripe) 19 RLY COM Green (White stripe) 20 RLY NC
Installation Installation Fixing the bracket and the product 1 Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws through the bracket to the position where AE-M will be installed. NOTE If installing AE-M on a concrete wall, drill holes, insert PVC anchors, and fix them with fixing screws. To avoid RF interference, a minimum separation distance must be maintained.
Installation 2 Install AE-M onto the fixed bracket. Wall 3 Assemble AE-M with the bracket by rotating the product fixing screw. Wall NOTE When assembling the product with the bracket, you can use the included bracket fixing screw(Star Shaped) instead of the product fixing screw for enhanced security.
Installation Power supply connection 21 - PWR +VDC 22 - PWR GND Red Black (White stripe) DC power AE-M NOTE Use a power supply adaptor of DC 12 V (± 10%) with a minimum of 1,000 mA which has obtained the approval of IEC/EN 60950-1. If you wish to connect and use another device to the power supply adaptor, you should use an adaptor with a current capacity which is the same or larger than the total power consumption required for the terminal and another device.
Installation LAN connection (connecting to a PC directly) AE-M has an automatic MDI/MDIX function so that it can be connected to a PC directly using a normal straight type CAT-5e cable, not a cross cable.
Installation Relay connection Fail Safe Lock In order to use the Fail Safe Lock, connect N/C relay as shown in the figure below. There is normally a current flowing through the relay for the Fail Safe Lock. When the relay is activated, blocking the current flow, the door will open. If the power supply to the product is cut off due to a power failure or an external factor, the door will open.
Installation Automatic door connection Door button 18 - RLY NO 19 - RLY COM Gray (White stripe) Green (White stripe) Sensor 18 Automatic door Controller 19 Door Lock AE-M 13
Installation Connecting as a standalone AE-M can be connected to the door lock, door button, and door sensor directly without connecting a separate I/O device.
Installation Connecting to Secure I/O 2 Secure I/O 2 is an I/O device, can be connected to AE-M with the RS-485 cable. Security can be maintained even if the connection between AE-M and Secure I/O 2 has been lost or the power supply to AE-M has been shut off due to external factors. Use the RS-485 cable with AWG24, twisted pair, and less than 1.2 km in length. If connecting with a RS-485 daisy chain, connect the termination resistor (120 Ω) to both ends of the daisy chain connection.
Installation Wiegand connection AE-M Use as a Wiegand input/output device 12 - WG GND 13 - WG D1 14 - WG D0 RFID reader / Control device 16 Black White Green
Installation Resetting Network Settings 1 Turn the power on. 2 Press and hold the reset button on the rear of device until the device restart automatically. 3 Connect the device with default values. TCP/IP address: DHCP address assignment (If DHCP address assignment is failed, 169.254.x.x will be set.) Server mode: Disabled RS-485: Default, 115200 bps 4 Change the TCP/IP address or RS-485 information. 5 Turn the power off later on and then check the network setting is properly.
Product specifications Product specifications Category Credential General LF card option HF card option NFC card BLE card RF read range * CPU Memory LED Sound Operating temperature Storage temperature Operating humidity Storage humidity Dimension (W x H x D) Weight Capacity Interface IP rating IK rating Certificates Max. User Max. Card Max.
Product specifications Dimensions (Unit: mm) * The tolerance is ±0.3mm. 144.7 48 27 132.2 39.
FCC compliance information EU Declaration of Conformity (CE) This product is CE marked according to the provisions of the Radio Equipment Directive (RED) 2014/53/EU. Hereby, MOCA System Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU. • Bluetooth Transmit Power: 2.1dBm • Bluetooth Frequency: 2402~2480 MHz • NFC Frequency: 13.56 MHz • RFID Frequency: 134.
Appendices Appendices Disclaimers The information in this manual is provided with regard to the MOCA System 's products. The right to use is acknowledged only for products included in the terms and conditions of the sales agreement guaranteed by MOCA System. The right of license to other intellectual property rights not discussed in this manual is not acknowledged.
Appendices that you have the freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things. To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights.
Appendices The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form.
Appendices interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
Appendices License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire Program remains governed by this License without regard to the additional permissions. When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it.
Appendices You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. Patents.
Appendices General Public License “or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation.
Appendices If you modify a copy of the Library, and, in your modifications, a facility refers to a function or data to be supplied by an Application that uses the facility (other than as an argument passed when the facility is invoked), then you may convey a copy of the modified version: • a) under this License, provided that you make a good faith effort to ensure that, in the event an Application does not supply the function or data, the facility still operates, and performs whatever part of its purpose re
Appendices OpenSSL License Copyright (c) 1998-2017 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Appendices cannot simply be copied and put under another distribution licence [including the GNU Public Licence.
EU Declaration of Conformity (CE) This product is CE marked according to the provisions of the Radio Equipment Directive (RED) 2014/53/EU. Hereby, Suprema Inc. declares that this product is in compliance with the essenti al requirements and other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU. The RF distance between body and product is 20cm This device meet the EU requirements on the limitation of exposure of the general public to electroma gnetic fields by way of health protection.
FCC Instructions FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
IC Instructions Industry Canada Statement This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-247 d’Industrie Canada applicable aux appareils radio exempts de licence.
