Table of Content Content 1. Product Introduction 2. Installation of Transmitter 2.1 Receive ID Mode---LF004 setting for clamp transmitter 2.2 Start to install TX012 2.3 Special set up : Manual Input New Transmitter ID Code 3. Limit Warranty 3.1 Warranty Service 3.2 What Are Not Covered 4. Thing to Notice 5.
1 Product Introduction LF004 is a controller, used to set transmitter ID of every wheel to LCD screen of digital receiver. Take the models of TX014 and RX003 to help explain how to use LF004 completely. TX014 : a kind of transmitter RX003 : a kind of LCD screen of digital receiver TX014 contains highly accurate sensors to detect tire pressure and temperature. Before installing TX014 on the Wheel Rim, receive and set TX014 ID Mode to RX003 by using LF004.
2.1 Receive ID Mode---LF004 setting for clamp transmitter 1. Put the 12DCV POWER CABLE to the Power Plug Receiver. Antenna 2. Tighten the Antenna. 3. Check if the LCD of the Receiver shows “??P“. 4. Simultaneously press button and for more than 2 seconds to enter “Receive ID Mode”. 5. Check if the LCD of the Receiver shows. “Receive ID“. 6. Turn on the LF004.
7. Select one of the tires you want to set up. NOTE: The signal active distance of LF004 is 0.3m. 8. Put LF004 near the transmitter at least 30mm. 9. We suggest that installing the tire after setting. 10. IMPORTANT: When setting, please keep other transmitter away from the setting transmitter at least 1m. NOTE: If you are not sure it receives the signal or not please do it again or refer to Item Manual input new transmitter ID code 11. Push the button of “ENTER” And the “SEND” LED will flash.
13. If the transmitter is already in the tire, you will see the tire pressure. 14. IMPORTANT: If you want to check the tire as usual ,you may push any button of LF004 and RX003 will show the pressure(The signal active distance of LF004 is 0.3m ) 15. After setting, push button the LCD of the Receiver shows “Receive ID Cancel” 16. As the voltage is below 2.3V, pushing any button will make the “SEND” LED flash every 4secs. NOTE The value above is for reference. 2.2 Start to install TX012 1.
2. Install the clamp. IMPORTANT Before install the clamp, please check if the ID of the transmitter had been set up . 3. Make sure arrow on the transmitter point to rubber valve side. 4. Put the transmitter in the lowest area of the rim or drop center, and beside valve. Tighten the strap.(Torqre must over 0.35 kfg-m) Suggestion: Place lock of strap opposite to transmitter mounting position for better tire rebalancing. 5.
. Reverse the above steps to remove a transmitter. Suggestion: Tell technician that you have installed TPMS before he changes the tire. 2.3 Special set up : Manual input new transmitter ID code (Please contact with us) 1. Simultaneously press button and for more than 2 seconds to enter “Special Set Up Mode”. 3. LCD Display will show New ID Input 5. Use button (act as downward button) and button (act as upward button) to select a number Press button to confirm then move to 2.
3.
3.2 This Limited Warranty Provided by Mobiletron Does Not Cover (1) Product that have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, improper transportation, repair or service in any way that is not authorized by Mobiletron. (2) Any damage attributable to fire, flood, lightning strike or act of God. (3) This limited warranty coverage will exclude the package material and user manual.
5. Technical Specifications 5.1 Operation Condition ! " ' ! " ( " # $ # % & # $ # & $ * ) 5.2 Radio Transmitter + , - $ % .( / # ' ) + " ' " 0 0 5.
FCC Caution: 1.The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3.