User Manual

ManualsBrandsMobile Technologies ManualsElectronicsMerchandise Theft Deterrent System with Zigbee and RFID

FREEDOM MICRO

MANUAL

www.MTIGS.com | T:800.426.6844

REMOVING SMARTCABLE

ATTACHING SMARTCABLE™

Plug SmartCable into the charge port of the device.

Twist the device and bracket off of the position.

The loose cable can be clipped into SpeedBracket™

for easy storage.

Insert SmartCable into the charge port on the puck.

The hooks on cable should click when fully seated.

Insert the crescent end of the

Freedom Micro II

tool

into the opening to the right of the LED. Twist the

Freedom Micro II tool

clockwise 45 degrees and hold

it in place.

Remove the SmartCable from the puck.

Phone should be turned ON, and unlocked

before inserting SmartCable™ while in

MTI Connect® mode.

Summary of content (9 pages)

PAGE 1
ATTACHING SMARTCABLE™ 1 Insert SmartCable into the charge port on the puck. ® FREEDOM MICRO II HS MANUAL 2 Plug SmartCable into the charge port of the device. 2 Twist the device and bracket off of the position. 4 The loose cable can be clipped into SpeedBracket™ for easy storage. The hooks on cable should click when fully seated. Phone should be turned ON, and unlocked before inserting SmartCable™ while in MTI Connect® mode.
PAGE 2
RFID COMMANDS ® FREEDOM MICRO II HS MANUAL Default Mode Enter Standard Mode AUTHORIZATION Double Beep Program User Card Exit Programming Mode ™ VERSA KEY Flash White every 8 seconds: Disarmed AUTHORIZATION Double Beep Double Beep Arm/Disarm Position Auto time out if no user cards are added, reverts to Default mode. Set Lockdown/Unlock While Armed Tap and Hold Access Card for 10 seconds. It will double beep immediately, and double beep again after 10 seconds.
PAGE 3
RFID MTI CONNECT PAIRING ® FREEDOM MICRO II HS MANUAL Default Mode Enable Pairing Mode on MTI Connect Hub ® Insert MTI Connect IntelliKey™ for 10 seconds. Network System m Sta Status tat ta atu Power Reset Enter Network Mode Position fails to connect to mesh network within 3 minutes: Double Beep Four Fast Reject Beeps ™ VERSA KEY Position connects successfully to mesh network: NETWORK PAIRING Slow Beeps www.MTIGS.com | T:800.426.
PAGE 4
LED STATUS INDICATORS Visual Reference ® FREEDOM MICRO II HS MANUAL System Status Condition Solid White Puck is armed and docked. Single white ﬂash every 5 seconds Puck is armed and lifted. Double white ﬂash every 8 seconds Puck is docked, but not armed, puck is connected to a mesh network. Flashing Red and White with audible alarm Flashing Red and White with no audible alarm Solid Yellow Alarm has been triggered. silence the alarm and inspect the tether, puck trigger, and base trigger.
PAGE 5
LED STATUS INDICATORS ® FREEDOM MICRO II HS MANUAL Visual Reference System Status Flashing Yellow Every 5 Seconds Solid Blue Condition Puck is armed, lifted, puck is NOT connected to a mesh network. Only applicable in Network Mode. After tapping an authorization card: The puck is in enrollment mode. Tap VersaKey™ to authorize them for use in standard mode. Enrollment mode closes automatically in 3 minutes. In normal use: Overcurrent in charging circuit – most likely a problem in the SmartCable™.
PAGE 6
RISER DIMENSIONS 4.36” ® FREEDOM MICRO II HS MANUAL 2.74” 3.45” 60° 4.38” 2.05” 1.84” PUCK DIMENSIONS 1.85” 1.28” 1.85” www.MTIGS.com | T:800.426.
PAGE 7
RISER WITH ADAPTER DIMENSIONS 4.36” ® FREEDOM MICRO II HS MANUAL 2.74” 3.45” 60° Slot Adapter shown. Through-hole adapter is identical in size/ appearance minus these tabs. 1.89” 4.38” 2.80” www.MTIGS.com | T:800.426.6844 1.
PAGE 8
BRACKET DIMENSIONS ® FREEDOM MICRO II HS MANUAL MAXIMUM: 180mm H x 90mm W MINIMUM: 118mm H x 65mm W 1.11” Accomodates Phones 7-9mm Thick www.MTIGS.com | T:800.426.
PAGE 9
FCC AND ISED STATEMENT ® FREEDOM MICRO II HS MANUAL FCC ID: 2AA2X-15000282 Model: ROUND FREEDOM MICRO II HS FCC Statement This device complies with Part 15 of the FCC Rules. Caution: If any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.