CONTENTS ® FREEDOM MICRO II HS MANUAL Product Manual for ® FREEDOM MICRO II HS Contents 1. Components And Accessories 2 2. Baseplate Options 3 3. Speedplate™ Merchandising 5 4. Speedbracket™ Merchandising 8 5. SmartCable™ Merchandising 10 6. RFID Commands 11 7. RFID MTI Connect® Pairing 12 8. LED Status Indicators 13 9. Dimensions 15 10.
COMPONENTS AND ACCESSORIES ® Freedom Micro II Puck ® FREEDOM MICRO II HS MANUAL Freedom Micro® II Riser SpeedBracket™ Mounting Options VHB Mounting Through Hole Mounting Slot Mounting Power Supply Freedom Micro® II Tool SpeedPlate™ Options Phones Tablets Only use 5.9V 3.5A MTI Power Supply, not exceed PS 2. Other spec may cause damage. www.MTIGS.com | T:800.426.
BASEPLATE OPTIONS - ADHESIVE 1 Route the cable as desired and attach the baseplate with ® FREEDOM MICRO II HS MANUAL 2 Peel the red film from the adhesive. the included screws. Routing out the back Routing out the bottom 3 Place Micro position in desired location. Press down on the base plate for 10 seconds for full adhesive contact. Allow 24 hours for full adhesion. 4 Use the individual power supply and plug it into the nearest outlet.
BASEPLATE OPTIONS - SLOT & THROUGH-HOLE ADAPTERS MOUNTING SLOT & THROUGH-HOLE ADAPTERS ® 1 Insert the Freedom Micro II position into the slot or hole. ® 3 Secure the Freedom Micro II position with the knob. 2 Place the power cable into the slot on the bottom plate, then slide it up over the slot adapter post. 4 Use the individual power supply and plug it into the nearest outlet. Use an outlet installed near the equipment that is easily accessible. www.MTIGS.com | T:800.426.
SPEEDPLATE™ MERCHANDISING 1 Clean the device with an alcohol wipe. ® FREEDOM MICRO II HS MANUAL 2 SpeedPlate™. 3 Apply the SpeedPlate™ to the phone, with the cable retainer towards the charge port of the phone. Use the SpeedPlate™ cable retainer as alignment reference. www.MTIGS.com | T:800.426.6844 4 Place the device onto the puck and rotate the device clockwise on the puck until it locks into place.
REMOVING SPEEDPLATE™ FROM PUCK ® 1 Insert the crescent end of the Freedom Micro II tool position, rotate the SpeedPlate™ counterclockwise. www.MTIGS.com | T:800.426.6844 ® 2 Twist the Freedom Micro II tool clockwise 45 degrees and hold it in place. 4 Remove the SpeedPlate™ from the Freedom Micro II ® Puck, then release and remove the Freedom Micro II tool. into the opening to the right of the LED.
REMOVING SPEEDPLATE™ FROM DEVICE 1 Place the SpeedPlate™ removal tool onto the ® FREEDOM MICRO II HS MANUAL 2 Rotate the tool clockwise. SpeedPlate™, aligning the holes on the tool with the rotation locks. 3 Roll any remaining adhesive off of the device. REMOVING PUCK FROM TETHER 1 Lift puck out of riser, insert the crescent end of the Freedom Micro II tool into the opening below the charge port on the puck. Twist the Freedom Micro II tool counterclockwise to unlock the puck from the tether. www.
SPEEDBRACKET™ MERCHANDISING 1 Loosen the center screw on the universal bracket to loosen the bracket arms. ® FREEDOM MICRO II HS MANUAL 2 Extend the bracket arms as far as needed. The bracket arms move simultaneously in pairs (top & bottom, and left & right). 1. 2. 2. 1. Open the top and bottom bracket arms, then the side arms, in that order. 3 Place the phone into the universal bracket. www.MTIGS.com | T:800.426.6844 4 Adjust the universal bracket to fit the device snugly.
SPEEDBRACKET™ MERCHANDISING 5 Tighten the center screw on the SpeedBracket™ to ® FREEDOM MICRO II HS MANUAL 6 Place device back onto puck. secure the bracket arms in place around the device. After tightening screw, wiggle the arms to ensure they have fully engaged the lock teeth, then re-check screw for tightness. 7 Rotate the device and bracket clockwise on the puck 8 until it locks into place. *click* www.MTIGS.com | T:800.426.