Installation Guide

ManualsBrandsMMI Door ManualsDoors & Windows72 in. x 80 in. White Aluminum Inswing Retractable Double Screen Door

• Screwdriver: ﬂat head and

Phillips head

• Pencil

• Hacksaw

FIG. 1B

FIG. 1A

RETRACTABLE SCREEN

DOUBLE INSWING

ASSEMBLY AND INSTALLATION INSTRUCTIONS

STEP 1: REVIEW & CHECK

A) CONFIRM DOOR HEIGHT & WIDTH

You have purchased a DOUBLE Retractable Screen for an

INSWING door.

HEIGHT: Please make sure that the screen unit you have

purchased matches your door height.

WIDTH:Full-Size: If this screen unit is FULL-SIZE, it will ﬁt door

widths of 6/0 (without cutting) and 5/4 or 5/0 (with cutting).

Please make sure that your door width is 6/0, 5/4 or 5/0

B) PART REVIEW

Verify that the following components are included in the box.

Parts are listed from left to right. See Figure 1A >

1. Screen Housing marked A and D (1)

2. Screen Housing marked B and C (1)

3. Screen Track with locking hardware marked A and B (1)

4. Screen Track with locking hardware marked C and D (1)

5. Screen Track Covers (2)

6. Mounting Screws for corner and tracks

a. Four - #8 x 3” phillips head tapping screws

b. Five - #8 x 1-1/2” phillips head tapping screws

c. Four - #8 x 5/8” phillips head tapping screws

d. Five - #8 x 1/2” phillips head self-drilling screws

e. Four - #8 x 1” self-drilling screws

7. Screen Housing Circular Screw Covers (4)

C) TOOLS REQUIRED See Figure 1B >

Page 1 of 7

• Level

• Square

• Tape Measure

• Drill

Summary of content (7 pages)

PAGE 1
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 1: REVIEW & CHECK FIG. 1A 1 A) CONFIRM DOOR HEIGHT & WIDTH You have purchased a DOUBLE Retractable Screen for an INSWING door. 2 3 4 5 HEIGHT: Please make sure that the screen unit you have purchased matches your door height. 6a 6b 6c 6d 6e WIDTH:Full-Size: If this screen unit is FULL-SIZE, it will ﬁt door widths of 6/0 (without cutting) and 5/4 or 5/0 (with cutting).
PAGE 2
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 2: ASSEMBLY PREPARATIONS FIG. 2A Very important! Please examine the picture at right for additional details. See Figure 2A > Before proceeding to assembly, please look at the back of the header and sill screen tracks. There you will ﬁnd the numbers 6/0, 5/4 and 5/0 printed on each end of the track. These numbers correspond to the door unit size that the screen will ﬁt onto.
PAGE 3
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 3: ASSEMBLY FIG. 3A Place all the items from the box on the ﬂoor in front of the patio or single door where the single screen is to be installed. The screen housings and tracks should line up with their corresponding letters in a clockwise fashion, as shown at right: A to A, B to B, C to C, D to D. See Figure 3A > B B A A Slide each screen track onto both the handle and housing slide guides.
PAGE 4
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 3: ASSEMBLY (continued) FIG. 3C FLIP AND TIGHTEN We now need to tighten the assembled screen unit. Flip the screen unit up and away from the door where the screen will be installed so that you now see the back side of the screen unit. Using the #8 x 5/8” phillips head tapping screws, lock the screen housing arm to the screen track by tightening. Repeat for all four corners.
PAGE 5
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 4: INSTALLATION FIG. 4A CONFIRM BRICKMOLD SURROUNDS DOOR Ensure brickmold completely surrounds door The screen unit will be mounted directly to the brickmold on the outside of the door frame. If there is no brickmold outside your door frame, you will need to purchase brickmold. This will ensure that the jamb, head and sill are ﬂush so that the screen unit will operate smoothly.
PAGE 6
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 4: INSTALLATION (continued) FIG. 4C MOUNT HEAD TRACK TO DOOR FRAME After positioning the screen frame on the door opening and making sure the two screens meet up in the center correctly with the door, screw the head track into the door frame. See Figure 4C > Screw in only two of the four #8 X 1-1/2” screws because you may need to adjust the position of the screen unit to make sure that the screen is square and level.
PAGE 7
RETRACTABLE SCREEN DOUBLE INSWING ASSEMBLY AND INSTALLATION INSTRUCTIONS STEP 4: INSTALLATION (continued) FIG. 4F INSERT REMAINING SCREWS Add the rest of the screws to the screen head track and tighten. Finish by screwing the screen housing at each corner with #8 x 3” screws. All screws should be securely fastened at this stage. See Figure 4F > SNAP IN SCREEN TRACK & SCREW COVERS Now snap in the screen track covers to the front sides of both screen tracks.