User's Manual

ManualsBrandsMMB Research ManualsElectronicsRADPIDSE ZIGBEE SMART ENERGY

RapidSE ZigBee Smart Energy Module

RSE.ESP.MMB-PA.1.0, RSE.DVC.MMB-PA.1.0

Rev 1.2

The RapidSE Module is a drop-in ZigBee Smart Energy solution.

Preloaded with MMB Research’s RapidSE ZigBee Smart Energy

application, it oﬀers hardware vendors an easy way to integrate

a fully-implemented ZigBee Smart Energy platform into their

existing devices.

MMB Research oﬀers a variety of hardware and software

development tools to facilitate integration. For more

information, please visit http://www.mmbresearch.com

Contents

1 | General Information 2

2 | Module Pinout 2

3 | Electrical Specications 3

3.1 | Absolute Maximum Ratings 3

3.2 | Recommended Operating Conditions 3

3.3 | DC Electrical Characteristics 3

4 | RF Specications 4

4.1 | Receive Speciﬁcations 4

4.2 | Transmit Speciﬁcations 5

4.3 | Synthesizer 5

5 | Functional Specications 6

5.1 | Serial Ports 6

5.2 | GPIO 7

5.3 | Analog to Digital Converter (ADC) 8

6 | Mechanical Specications 9

6.1 | Physical Dimensions 9

6.2 | Recommended Land Pattern (Surface Mount) 10

6.3 | Connector Speciﬁcations 11

6.4 | Labelling 11

7 | Regulatory Approvals 11

7.1 | FCC 11

Summary of content (12 pages)

PAGE 1
RapidSE ZigBee Smart Energy Module RSE.ESP.MMB-PA.1.0, RSE.DVC.MMB-PA.1.0 Rev 1.2 The RapidSE Module is a drop-in ZigBee Smart Energy solution. Preloaded with MMB Research’s RapidSE ZigBee Smart Energy application, it offers hardware vendors an easy way to integrate a fully-implemented ZigBee Smart Energy platform into their existing devices. MMB Research offers a variety of hardware and software development tools to facilitate integration. For more information, please visit http://www.mmbresearch.
PAGE 2
1 | General Information Note that some of the specifications refer to either EM250 or Module. Please note specifications cited as EM250 are taken from the EM250 datasheet (this should also be noted where referred to). Module means measurements taken with our production module. 2 | Module Pinout Numbers in parentheses are the EM250 pin number.
PAGE 3
| Electrical Specifications 3.1 | Absolute Maximum Ratings Parameter Supply Voltage (VCC) Voltage on any GPIO[0:16], SIF CLK, SIF MISO, SIF MOSI, nSIE LOAD, nReset Ambient Operating Temperature Storage Temperature Minimum -0.3 -0.3 -40 -40 Maximum 3.6 VCC +0.3 +75 +125 Units V V °C °C Minimum 2.7 -40 Typical 3.3 Maximum 3.6 +75 Units V °C Minimum Typical 61.4 Maximum Units mA 3.2 | Recommended Operating Conditions Parameter Supply Voltage (VCC) Temperature Range 3.
PAGE 4
| RF Specifications 4.1 | Receive Specifications Table 4.1 | Module Receive Characteristics Parameter Receive sensitivity Receive sensitivity (Boost) Input 1dB Compression Input IP3 Test Condition Max gain Max gain CW Two -7 dBm CW tones spaced 1 MHz apart Min Typical -97.56 -99.53 +26 +36 Max Units dBm dBm dBm dBm Table 4.2 | Receive Strength Signal Indicator (RSSI) Accuracy Channel 18 18 18 18 18 18 Actual Level -40 -50 -60 -70 -80 -90 Measured RSSI -40.0 -50.0 -60.0 -70.0 -79.0 -89.
PAGE 5
Table 4.3 | Continued Parameter Relative frequency error (2x40 ppm required by IEEE 802.15.4) Relative timing error (2x40 ppm required by IEEE 802.15.4) Linear RSSI range RSSI Range Test Condition Minimum -120 Typical Maximum Units +120 ppm -120 40 -90 +120 ppm -30 dB dB 4.2 | Transmit Specifications Table 4.
PAGE 6
5 | Functional Specifications 5.1 | Serial Ports Refer to the EM250 data sheet for functionality and associated GPIO pin outs. Note: The module pin out table in section 2 of this document provides a cross reference between the MMB PA module pins and the EM250 GPIO. 5.1.1 | SC1 (UART, SPI, I2C) The SC1 module provides asynchronous (UART) or synchronous (SPI or I2C) serial communications.
PAGE 7
5.1.2 | SC2 (SPI, I2C) The SC2 module provides synchronous (SPI or I2C) serial communications. The SC2 SPI mode has the following features: • The SPI mode of the SC2 supports both master and slave modes. • It has a fixed word length of 8 bits. • Master and slave modes • Full duplex operation • Programmable master mode clock frequency (12MHz max.
PAGE 8
5.3 | Analog to Digital Converter (ADC) The ADC is a first-order sigma-delta converter sampling at 1MHz with programmable resolution and conversion rate. the ADC Module supports both single-ended and differential inputs.
PAGE 9
6 | Mechanical Specifications 6.1 | Physical Dimensions R1 R4 L R2 A5 A N T E N N A R3 32 A4 22 21 W 12 1 11 A1 A3 A2 0.6 mm 0.8 mm Symbol L W H A1 A2 A3 A4 A5 R1 R2 R3 R4 2.
PAGE 10
6.2 | Recommended Land Pattern (Surface Mount) 32 22 module outline 21 F1 12 1 F4 11 F2 F3 0.854 mm d = 0.8 mm 3.94 mm 1.51 mm Symbol F1 F2 F3 F4 Description Distance pad edge to pad edge Distance pad edge to pad edge Distance pad center to pad center Pitch Distance 21.9 mm 1.523 mm 1.3 mm 2 mm Note: It is advised that for surface mount applications, through holes / vias should not be designed into the carrier board.
PAGE 11
6.3 | Connector Specifications 6.3.1 | Edge Mount (USNAP) Connector 10 pin 2mm pitch right angle female header 6.3.2 | SIP Header / Socket 11 + 11 + 10 (if no USNAP populated) pin 2mm pitch 0.8mm diameter through hole footprint 6.4 | Labelling 0.75” 0.75” 7 | Regulatory Approvals 7.1 | FCC 7.1.1 | FCC Notice This device (ZGB.MMB-PA.1.0/ZGB.MMB-PA-LNA.1.0) complies with Part 15 of the FCC rules.
PAGE 12
7.1.2 | Modular Approval This device (ZGB.MMB-PA.1.0/ZGB.MMB-PA-LNA.1.0) meets the requirements for modular transmitter approval as detailed in the FCC public notice DA 00-1407. It should be noted that: “While the applicant for a device into which an authorized module is installed is not required to obtain a new authorization for the module, this does not preclude the possibility that some other form of authorization or testing may be required for the device (e.g.