MITSUMI CR Series CD-R/RW Drives INSTALLATION MANUAL VERSION 5.
Mitsumi Internal CD-ReWritable Quick Installation Guide 1. Start by shutting down the computer along with the monitor and any other peripherals. 2. Unplug the power cord from the computer. 3. Remove the computer case cover. 4. Remove the cover from an empty drive bay. 5. Attach mounting rails or brackets to the drive if required. 6. Note the pairs of pins on the back of the drive labeled: Master, Slave and Cable Select. 7. Note that one of the pairs has a small jumper between them.
Rear View of the Drive Power Cable Audio Cable 40-pin Interface Cable Pin #1 Power Cable - Supplies power to the CD-R drive from a standard PC AT power supply. 40-pin Interface Cable - Connection for 40-pin ribbon IDE interface cable. Audio Cable - Provides stereo audio output to a sound card. CAUTION: The discharge of static elctricity can damage electronic circuitry.
Mitsumi External CD-ReWritable Quick Installation Guide 1. Using an audio cable, connect your drive to your speakers. 2. Next, connect the power cable and plug into a power source. 3. Turn the power of the External CD-R/RW Drive on. 4. Connect the USB cable to the PC. 5. The PC will automatically detect the External CD-R/RW Drive. Click “Next>”. 6. Check “Search for the best driver for your device” and click “Next>”. 7. Check “Floppy disk drives”.
Rear View of the Drive Power Switch USB Connector Audio Out Power Cable Power Cable - Supplies power to the external CD-R/RW drive . USB Connector - Connection for USB interface cable. Audio Out - Provides stereo audio output to a speaker.
Safety Information Please follow all safety warnings and instructions printed in this manual and on the CD-R/RW drive to avoid damaging your drive or harming yourself. Never attempt to service the drive yourself. No user serviceable parts are inside the unit. Opening or removing the cover can expose you to dangerous voltage levels, laser beams, and other hazards. Do not attempt to open the unit. The laser beam used by the CD-R/RW drive can be harmful to the eyes.
Federal Communications Commission (FCC) Information This unit generates and uses radio frequency energy and if it is not installed and used properly in strict accordance with the manufacturer’s instructions, it may cause interference with radio and television reception.
FCC Declaration of Conformity MITSUMI CR-4802TE CR-4802TU CR-4803TE CR-4804TE The device complies with part 15 of the FCC (U.S.A.) rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. MITSUMI Electronics Corp. 5808 W.Campus Circle Dr. Irving, TX. 75063 Tel.
CR-4802TE Specifications Supported Disc Formats CD-ROM Mode 1; CD-DA; CD-i; Video CD; CD-Extra (CD Plus) CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD Writing Methods Disc-at-Once, Track-at-Once, Multisession, Packet Writing Disc Diameters 12 cm, 8 cm Interface ATAPI specification SFF-8020i/8080 Data Transfer Rate (Average) Read: 1200Kbytes/sec (Mode 1), 1400 Kbytes/sec (Mode 2) Write: 600 Kbytes/sec (Mode 1), 700 Kbytes/sec (Mode 2) IDE Data Transfer Rate (Burst) 11.1 Mbytes/sec (16 bits PIO mode) 13.
CR-4802TU Specifications Supported Disc Formats CD-ROM Mode 1 and 2; CD-DA; CD-i; Video CD; CD-Extra (CD Plus) CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD (read), CD UDF Writing Methods Disc-at-Once, Track-at-Once, Multisession, Packet Writing Disc Diameters 12 cm, 8 cm Interface USB Interface Data Transfer Rate (Maximum) Read: 1200KB/s (8X speed) Write: 600 KB/s (4X speed) Rewrite: 300 KB/s (2X speed) Average Access Speed Random 200 ms typical (8X speed) Data Buffer Size 2 MB Audio Channels Sampling
CR-4803TE Specifications Supported disc formats CD-ROM Mode 1; CD-DA; CD-i; Video CD; CD-Extra (CD plus) CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD Writing Methods Disc-at-Once, Track-at-Once, Multisession, Packet Writing Disc diameters 12 cm, 8 cm Interface ATAPI specification SFF-8020i/8080 Data transfer rate Read:(MAX) 3000 Kbytes/sec (Mode 1), 3500 Kbytes/sec (Mode 2) Write:(average) 600 Kbytes/sec (Mode 1), 700 Kbytes/sec (Mode 2) (Compatible only with 2x speed recording for CD-RW disc) IDE Dat
CR-4804TE Specifications Supported disc formats CD-ROM Mode 1; CD-DA; CD-i; Video CD; CD-Extra (CD plus) CD-ROM XA Mode 2 Form 1 and Form 2; Photo CD Writing Methods Disc-at-Once, Track-at-Once, Multisession, Packet Writing Disc diameters 12 cm, 8 cm Interface ATAPI specification SFF-8020i/8080 Data transfer rate Read:(MAX) Write:(average) 3600 Kbytes/sec (Mode 1), 4200 Kbytes/sec (Mode 2) 600 Kbytes/sec (Mode 1), 700 Kbytes/sec (Mode 2) IDE Data transfer rate (Burst) 16.
Licenses and Trademarks: Product names mentioned in this manual are trademarks or registered trademarks of their respective companies and are hereby acknowledged. Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. The software described in this manual is furnished under a license agreement and may be used or copied only in accordance with the terms of that agreement. Printed in USA.