Mitsumi Electric Co., Ltd. Wavit11 User's Manual Wavit11 User’s Manual Revision 1.
Mitsumi Electric Co., Ltd. Revision History December 6, 2001 January 19, 2002 Wavit11 User's Manual Revision 1.0 Translated from Japanese edition (Rev. 1.0) Revision 1.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual Contents Revision History............................................................................................2 About This Guide..........................................................................................5 Regulatory Compliance Notices ................................................................6 1. Preface....................................................................................................8 1. Preface................
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 9. Wavit11Setting up ................................................................................. 79 9.1. Connection to personal computer..................................................... 80 9.2. Connection to Printer ...................................................................... 81 9.3. Connection to Network Equipment.................................................. 82 10. Items that can be set with Configuration Utility ..................
Mitsumi Electric Co., Ltd. Wavit11 User's Manual About This Guide Absolutely do not do the operation when the instruction is given with this mark. Please pay attention in the case you do the operation indicated with this mark. The relevant usage is explained. Please refer, as occasion demands. This is for an explanation such as terminology.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual If this product is used near the television set or radio receiver, the TV display may be sometimes disturbed or the noise may be heard in audio output. In such a situation, it will be necessary to install this product far from TV and radio set. This product may affect the medical apparatus, so you cannot install this product inside a hospital.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 1. Preface Thank you for purchasing the Wavit11. This user’s manual includes various notices to allow you to use the Wavit11 safely and properly. Keep this anytime and read carefully. In this way, you can always refer to this. 2. Accompanied Accessories The following accessories are accompanied to Wavit11. If you could not check all accessories, contact with the distributor.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 4. How to use Wavit11 1. Select a kind of wireless LAN network according to the omtended use of Wavit11. 2. Install Wavit11 Configuration Utility to the personal computer. 3. Set up the Wavit11 by using Wavit11 Configuration Utility. 4. In the case that an encryption is used, set up the encryption mode. 5. Set up Wavit11.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 5. About Wireless LAN Network There are 4 types of wireless LAN network that using Wavit11. Make a selection according to the usage of the wireless LAN network. Wireless LAN Type Ad-Hoc LAN IBSS LAN Infrastructure LAN Wireless Bridge Function The network consists of only wireless clients. The network consists of only wireless clients. The network combined both wired and wireless clients. The network connects two networks wirelessly.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 5.1. Ad-Hoc LAN The Ad-Hoc LAN is a network consisting of only wireless LAN. It is the network that does not connect to the Ethernet backbone and external network such as Internet. There is not a restriction on the number of wireless LAN units in the Ad-Hoc LAN. Set the communication mode of Wavit11 to “Ad-Hoc” mode.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 5.2. IBSS LAN The IBSS LAN is a network of only wireless LAN. It is the network that does not communicate to the Ethernet backbone and external network such as Internet. There is not a restriction on the number of wireless LAN units in the IBSS LAN. Set the communication mode of Wavit11 to “802.11 Ad-Hoc” mode.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 5.3. Infrastructure LAN Communication is established via an Access Point in the infrastructure LAN, therefore direct communication with other Wavit11s is not possible. This is the network that is used in such an occasion where Ethernet is being connected to Access Point and Internet access is carried out through Ethernet. Set the communication mode of one Wavit11 to “AP” mode and set the other Wavit11 communication mode to “Infrastructure” mode.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 5.4. Wireless Bridge The Wireless Bridge connects two wired network using two Wavit11. The maximum number of network equipment that can be connected to wired LAN is 16. Set the communication mode of Wavit11 to “Wireless Bridge” mode.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 6. Installation method of Wavit11 Configuration Utility 1. Confirm the operating system of personal computer and its version. 2. Confirm the existence of Ethernet port in your personal computer. 3. Confirm if the TCP/IP protocol is installed and set up appropriately in your personal computer. 4. In the case "Obtain an IP address automatically” is set in a TCP/IP of your personal computer IP address will be confirmed. 5.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 6.1. Microsoft Windows Version Wavit11 Configuration Utility runs on Microsoft Windows of the following version. OS Status Windows95 Windows95 OSR2 Windows95 OSR2.5 Windows98 OK Windows98 SE OK Windows Me OK Windows NT 4.0 WorkStation Windows 2000 Windows XP Notes Install 4.01 or above Internet Explorer Install 4.01 or above Internet Explorer Install 4.01 or above Internet Explorer Install 4.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 6.2. Confirm an Ethernet port Wavit11 Configuration Utility should be installed to the personal computer with Ethernet port. Also, the device driver needs to be set up appropriately. Confirm in accordance with the following procedure. [STEP1] Select “Start”->”Setting”->”Control Panel”. [STEP2] Click “Network” icon in the control panel.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP3] Check to see that an Ethernet adapter is installed in “Configuration” page. If there is no Ethernet adapter in the “Configuration” page, install Ethernet adapter according to the user’s manual of your personal computer or the user’s manual of Ethernet adapter you use. [STEP4] Click the “Cancel” button.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 6.3. Confirm the TCP/IP protocol The TCP/IP protocol should be installed to the personal computer with Wavit11 Configuration Utility. It is necessary that Wavit11 Configuration Utility is set up appropriately. Confirm the TCP/IP protocol in accordance with the following procedure. [STEP1] Select “Start”->”Setting”->”Control Panel” [STEP2] Click “Network” icon in the “Control Panel”.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP3] Check to see that the relevant TCP/IP protocol is installed that corresponds to the Ethernet adapter used in the “Configuration” page. Select TCP/IP protocol corresponding to the Ethernet adapter and click the “Properties” button.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP4] Confirm your selection in the “IP address” page. Which one is selected, either “Obtain an IP address automatically” or “Specify an IP address”? In the case that "Specify an IP address” is selected proceed to "STEP10". Consult your network administrator, in the case that you do not know whether you should select “Obtain an IP address automatically” or “Specify an IP address”.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP5] Click “Cancel” button. [STEP6] Click “Cancel” button.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP10] In the case that “Specify an IP address” is selected in the “IP Address” page, check that the “IP Address” and “Subnet Mask” are set. Take notes of the "IP Address" and "Subnet Mask" that are confirmed here. Return to “STEP5” in the case that “Obtain an IP address automatically” is selected. Consult your network administrator, in the case that an "IP Address" and "Subnet Mask" are not set.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP11] Click the “Cancel” button. [STEP12] Click the “Cancel” button.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 6.4. Confirm an IP Address [STEP1] Click “Start”->”Run” [STEP2] Input “winipcfg” to “Open” and click “OK” button.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP3] Select Ethernet adapter at “Adapter Address” in “IP Configuration” window. Install an Ethernet adapter, in accordance to the user’s manual of the personal computer and Ethernet adapter you use, in the case that no "Ethernet adapter" is discovered. [STEP4] Confirm the “IP Address” and “Subnet Mask”. Take notes of the “IP Address” and “Subnet Mask” you confirmed here.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual In “IP Address” and “Subnet Mask” are both “0.0.0.0”, it will mean that the IP address acquisition is not accomplished successfully. Click “Renew All” button to obtain an IP Address. [STEP5] Click “OK” button.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual 6.5. Installation of the Wavit11Configuration Utility [STEP1] Insert Wavit11Configuration Utility disk to drive A. [STEP2] Click “My Computer” icon. [STEP3] Click “3.5 ½ floppy (A:)” icon.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP4] Click “Setup” icon. The “Install Shield Wizard” window appears.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP5] Click the “Next>” button in “Install Shield Wizard” window. [STEP6] Select “Destination Folder”. Click “Next>” button to install the Configuration Utility to the default folder. Click the “Browse” button in the case that you want to install to a different folder.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP7] Select Program Folder. Click “Next>” button if you agree the default folder. If you prefer to install it to another folder, select from the “Existing Folders” and click “Next” button. The “Setup Status” appears.
Mitsumi Electric Co., Ltd. Wavit11 User's Manual [STEP8] Install Shield Wizard Complete appears. Click the “Finish” button.
