Setup guide

ManualsBrandsMitsubishi ManualsProjection TVWS-48513, WS-55513, WS-65513, WS-73513, WS-48613, WS-55613, WS-65613, WS-65713, WS-73713, WS-55813, WS-65813

Owner’s Guide

visit our website at

w w w.mit s u bish i -t v.com

Projection Television Models

WS-48513, WS-48613, WS-55513, WS-55613, WS-55813,

WS-65513, WS-65613, WS-65713, WS-65813, WS-73513, WS-73713

Summary of content (110 pages)

PAGE 1
Owner’s Guide Projection Television Models WS-48513, WS-48613, WS-55513, WS-55613, WS-55813, WS-65513, WS-65613, WS-65713, WS-65813, WS-73513, WS-73713 visit our website at w w w. m i t s u b i s h i -t v.
PAGE 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.
PAGE 3
Contents Chapter 1 Television Overview Thank You ........................................................................................................................................................8 Unpacking your New TV ...................................................................................................................................9 Special Features ........................................................................................................................................
PAGE 4
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
PAGE 5
IMPORTANT SAFEGUARDS , cont’d. 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13.
PAGE 6
PAGE 7
Chapter . . . 1 Television Overview Thank you.......................................................................................................8 Unpacking your New TV ...............................................................................9 Special Features.......................................................................................... 10 Front Control Panel ..................................................................................... 11 Back Panel ...........................
PAGE 8
Our Thanks... Thank you for choosing Mitsubishi as your premier Home Entertainment provider. This Owner’s Guide describes the features and functions of your Mitsubishi widescreen, high definition TV. We urge you to examine this Owner’s Guide to become familiar with the innovative features and operations this unique television offers. The very core of our corporate philosophy is to provide our customers with the very best.
PAGE 9
FF/FWD STOP PAUSE REW/REV PLAY REC FORMAT PIP DEVICE CONNECT VIDEO SLEEP AUDIO EXCH INFO PIP/POP V-CHIP DEVICE MENU TVMENU PIP CH MUTE VOL CH DEVICE 9 QV 8 0 7 SQV POWER 3 6 2 5 1 4 HOME Your new High Definition bigscreen television has many special features that make it the perfect center of your home entertainment system.
PAGE 10
Front Control Panel Control Buttons �� CARD 2 SmartMedia TM CARD 1 MMC & SD �� IEEE 1394 CARD 3 CompactFlash R CARD 4 M EMORY STICK ��
PAGE 11
Front Control Panel The buttons (previous page) on the Front Control Panel highlighted in gray are duplicated on the remote control. The top row of labels show the control functions when there are no TV menus displayed on the screen. The bottom row of labels show the control functions when the TV menus are displayed on the screen or when a special function has been activated. See Remote Control Overview page 28, for further details on the functions of these buttons.
PAGE 12
Back Panel � ��
PAGE 13
Back Panel � ��
PAGE 14
IMPORTANT NOTES Warning: Do not leave stationary PIP/POP, or letterbox images on the screen for extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty. The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should fill the screen with constantly moving images rather than stationary images or patterns.
PAGE 15
Chapter . . . 2 Connecting External Devices and NetCommand Setup (overview)................................16 NetCommand Pre-Memorized Devices ........................................................17 Antenna or Wall Outlet Cable for Digital Broadcasts ..................................18 Separate UHF and VHF Antennas for Analog Broadcasts..........................18 Single Analog Antenna, Wall Outlet Cable....................................................19 Cable Box ..................................
PAGE 16
Connecting External Devices & NetCommand ® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device. NetCommand is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand will also automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device.
PAGE 17
NetCommand ® Pre-Memorized Devices Below is a list of several manufacturers devices tested and shown to be compatible with the NetCommand control system. When you use these devices you will be able to control them without changing the setting of the remote control from TV to another product. NetCommand may be able to operate additional models since many manufacturers use the same control signals to operate some or all of the models they offer.
PAGE 18
Connecting Antenna or Wall Outlet Cable for Digital Broadcasts Antenna or Wall Outlet Cable for Digital Broadcasts Figure 1 For cable or antenna with coaxial lead Connect the incoming cable to ANT-DTV on the TV back panel. Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable.
PAGE 19
Connecting a Single Analog Antenna, Wall Outlet Cable Single Antenna or Wall Outlet Cable for Analog Broadcasts TV back panel (section detail) Figure 3 For antennas with twin flat lead 1. For antenna with twin flat leads, connect the 300-Ohm twin leads to the 300-Ohm to 75-Ohm transformer. 75 Ohm Coaxial Cable 300 Ohm Flat Twin Lead 2. Push the 75-Ohm side of the transformer onto ANT-A on the TV back panel. 3 2 Note: 300-Ohm to 75-Ohm matching transformers are not provided with the TV.
PAGE 20
Connecting an Analog VCR V M-LINK CONTROL/ RS-232C RIGHT VCR to Analog Antennas or Wall Outlet Cable H LEFT VGA VIDEO 640 x 480 60Hz VGA AUDIO M-LINK/ DVI �� Connect two coaxial cables as follows � ANT-A LOOP-OUT ANT-B IR EMITTER NetCommand REPEATER � � �� 2. One from LOOP-OUT on the TV back panel to ANTENNA IN on the VCR back panel. 3. One from VCR back panel ANTENNA OUT to ANT-B on the TV back panel.
PAGE 21
Connecting an Analog VCR, continued Composite Video or S-Video and Audio Connections Figure 7 1. Connect a video cable from VIDEO OUT on the VCR back panel to VIDEO INPUT 1 on the TV back panel. If your VCR has a video channel or RF ON/OFF switch, set to OFF. Note: If you have an S-VHS VCR, follow the same steps using the S-Video terminals on the VCR and TV (in place of the composite terminals). 2. Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT 1 on the TV back panel.
PAGE 22
Connecting a DVD Player WARNING: Do not display the same stationary images on the screen for more than 15% of your total TV viewing in one week. Examples of stationary images are letterbox top/bottom bars from DVD or other video sources, side bars when showing standard TV pictures on widescreen TV’s, stock market reports, video game patterns, station logos, black or bright Closed caption backgrounds, web sites or stationary computer images.
PAGE 23
Connecting an External Digital TV (DTV or HDTV) Receiver DTV Connectors and Adaptors Figure 11 The TV back panel has 5 RCA-type connectors for the Input-DTV. The back panel of your external DTV receiver may use RCA-type connectors or BNC-type connectors. If your DTV receiver comes with BNC type connections, you will need to purchase BNC to RCA adaptors to connect the TV to the DTV receiver. These adaptors should be available at most electronic supply stores.
PAGE 24
Connecting an External Digital TV (DTV or HDTV) Receiver with RGB, HV Video Connections It may be necessary to obtain a VGA to RGB audio adaptor cable. These are available at most computer stores and many electronic stores. Some of the adaptor cables have RCA type connector ends, others have BNC type ends and will require adaptors as shown on page 21. 3 5 R e d External DTV Receiver with RGB, HV Video Connections Figure 13 1.
PAGE 25
Connecting MonitorLink™ with MonitorLink Control or DVI MonitorLink and MonitorLink Control � Figure 14 1. Connect a MonitorLink cable from the Mitsubishi Receiver/Controller back panel to the TV back panel. �� 2. Connect the L (left) and R (right) audio cables from the Mitsubishi Receiver/Controller to AUDIO LEFT and AUDIO RIGHT on the MonitorLink section of the TV back panel.
PAGE 26
Connecting the IR Emitter NetCommand ® or IR Repeater IR Emitter NetCommand® or IR Emitter Repeater After you have used 1A or 1B, IR Emitter NetCommand 2. Run the cable for each of the emitter ends under, along side or over the top of each device to be controlled to the area of the front where the remote control sensor is located. 1. Connect the plug end of the supplied Quadruple IR Emitter Cable to one of the IR Output NetCommand jacks on the TV back panel. 3.
PAGE 27
Chapter . . . 3 Basic Functions including NetCommand ® Setup and Editing Remote Control Functions: Overview ...........................................................28 Remote Control Functions: Operation and Care .........................................29 Programming the Remote Control to Control NetCommand A/V Products ...........................................................................................................30 3D Graphical Viewpoint Menu System.........................................
PAGE 28
Remote Control Functions: Overview Overview Figure 1, following page 17. V-CHIP: Turns On or Off the V-Chip Lock. 1. Slide Switch: Select A/V product to be controlled by the remote control. 2. Numbers: Individually select channels or enter information into menus. 18. INFO: Display on-screen summary of the current device used and any broadcast information available (including current V-Chip information). See Appendix D for details. 3. POWER: Turns power on and off for TV and other A/V products. 19.
PAGE 29
Remote Control Functions:Operation and Care Operation Figure 2 Installing the Batteries: CABLE/DBS/DTV VCR DVD AUDIO TV 1 1 2 3 4 5 6 7 8 9 SQV 4 0 QV 7 CH 8 VOL DEVICE 3 POWER 6 9 11 10 MUTE HOME CANCEL 16 15 V-CHIP INFO 17 18 19 20 PIP/POP EXCH SLEEP PIP CH AUDIO 22 21 23 PIP DEVICE 25 FORMAT 26 28 REC 30 REW/REV 34 12 13 DEVICE MENU 2. Load the batteries, making sure the polarities (+) and (-) are correct.
PAGE 30
Programming the Remote Control to Control NetCommand A/V Products To Program the Remote to Control NetCommand A/V Products Figure 3 (See NetCommand Supported Devices, for the list of A/V products supported by the NetCommand System.) 1. Move the slide switch at the top of the remote to the TV position. 2. Press and hold the POWER button on the remote control. 3. Enter the three digit code of 935, and then release the POWER button on the remote control. 4.
PAGE 31
3D Graphical Menu System Your TV has a special control system called NetCommand® that will control IEEE 1394 devices and selected older devices. For instructions on operating these control features, see the next page. Your TV also has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on-screen information for menu choices and changes, using the TV’s remote control.
PAGE 32
Using the Remote Control with NetCommand® Setup In order to use the TV’s NetCommand feature, you need to provide some detailed information during the setup of your Mitsubishi TV. You must define the Manufacturer Radio Buttons of the devices that are connected to the television, or learn the IR code remote control signals for the device connected.
PAGE 33
NetCommand ® Initial Setup Guide The easiest way to setup NetCommand is to follow the on-screen directions. For reference, below is a list of the screens that you will use. You will find detailed information regarding each screen in the pages following this Guide. Initial Initial NetCommand Setup: When you first turn on your TV. You may Cancel at any screen. Language Screen Page 35 Figure 1 Information Screen Page 35 Figure 2 Device Setup Screen (used when manufacturer is known).
PAGE 34
NetCommand ® Editing Guide The easiest way to setup NetCommand is to follow the on-screen directions. For reference, below is a list of the screens that you will use. You will find detailed information regarding each screen in the pages following this Guide. Change Add Change Device screen (select the device to change) Page 44 Figure 25 New Device screen (select the type of device to add to NetCommand) Page 40 Figure 14 Audio Video Receiver selected VCR selected Cable Box elected DBS, DVD, ETC.
PAGE 35
NetCommand ® Initial Setup When you first power On your new Mitsubishi TV, the initial setup screens appear. In order to use NetCommand, select these screens after you have connected the compatible equipment to the TV. Most IR remote control signal formats can be learned by NetCommand. Language Screen Device Setup Screen Figure 1 When you first turn on your TV, the Welcome screen displays and asks you to select either English or Spanish as the language for the on-screen menus.
PAGE 36
NetCommand ® Initial Setup, continued Review Screen Finish Screen After you have made your device choices the Review Screen will display. It is important to review the settings to ensure that they are correct. If necessary, you can use
PAGE 37
Edit NetCommand®, Adding an A/V Receiver A/V Receiver Screen Figure 6 If you selected “None” as the manufacturer of the A/V Receiver connected to the TV during the initial NetCommand Setup, you may Add the A/V Receiver and have NetCommand learn it. The same screens are displayed if using Edit NetCommand. 3. Select “Other”, skip Learn and select Next>. This will allow the device to appear and will allow NetCommand to switch inputs to use this device.
PAGE 38
Edit NetCommand ®, Adding an A/V Receiver, continued A/V Receiver Input Learn Screen Figure 8 NetCommand can now learn the remote control signals used to select each input on the A/VReceiver. A/V Receiver Learn Screen Figure 9 1. Press ADJUST or on the TV remote to select the check box for each function to be learned. 1. Press ADJUST or on the TV remote to select the check box for each function to be learned. 2.
PAGE 39
Edit NetCommand ®, Adding an A/V Receiver, continued Name Screen Figure 10 The Name screen allows you to change the default name for the A/V Receiver to a custom name of up to eight characters (including a blank space), selecting from letters, numbers, and nine different characters. Using the TV’s remote, press ADJUST or to select each letter, then press ENT(er) to move to the next position. Press CANCEL to delete the current letter and move back one character position.
PAGE 40
Edit NetCommand ®, Adding Devices Mitsubishi’s NetCommand offers the ability to edit your home theater configuration so that you can add new devices, change device settings and connection inputs, delete devices and even learn the remote control IR signals of devices that are not already in the NetCommand memory. NOTE: Select Next>, then press ENT(er) at each screen, to move forward to the next screen.
PAGE 41
Edit NetCommand ® Adding Devices, continued [Device] Screen Figure 15 If you selected “Other” in the Initial NetCommand Setup screen, then you can edit the device name and start learning. If you selected “None”, then you can add a device. If you have added a new device or changed an input in your home theater system, use this screen to start learning.
PAGE 42
Edit NetCommand®, Adding Devices, continued Please refer to the Editing Guide on page 34 to see if the screen described below is necessary for your device setup. [Device] Advanced Learn Screen Connection for [Device] Screen After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device. Most common IR remote control signal formats can be learned by NetCommand.
PAGE 43
Edit NetCommand ®, Adding Devices, continued Please refer to the Editing Guide on page 34 to see if the screen described below is necessary for your device setup. RF Connection for Cable Screen Input-DTV Connection Screen The RF Connection screen displays only when Adding or Changing a Cable Box. If your Cable Box is connected to a TV Antenna input, make sure the RF checkbox is checked. Select the TV antenna input that is used with the Cable Box.
PAGE 44
Edit NetCommand ®, Change or Delete Devices, Finish Screen Change Finish Screen Selecting Change from the Setup menu screen, displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V Receiver. If “Other” is selected for the manufacturer then you can also “Learn”. The rest of the screens that follow are the same as when you Add a device.
PAGE 45
Connecting IEEE 1394 Devices 4-Pin Style vs. 6-Pin Style There are two different types of connectors used for IEEE 1394 terminals and cables, a 4-pin and a 6-pin style. 4 pin connector 6 pin connector The 4-pin connector is capable of sending digital audio signals, digital video signals and digital control signals back and forth between devices. Your TV has three 4-pin type connection jacks available. One is on the front panel and two are on the back.
PAGE 46
Connecting IEEE 1394 Devices, continued When Connecting IEEE 1394 Devices • Do not loop the last device in the chain back to the TV. When the device chain is looped, the TV may not be able to work with the other devices. • Place devices that have only a mechanical (two-position) power switch at the end of the chain or leave the power switch in the ON position. When turned OFF, IEEE 1394 signals may not be able to pass through the device to other devices.
PAGE 47
Adding IEEE 1394 Devices Automatically IEEE 1394 Device Type Screen Connection Screen If the new IEEE 1394 device is also connected using analog inputs, you will need to define the device type. Select the type of device, such as a VCR. Select the TV input that you used when you connected the video or S-Video cables. You may also select the TV or A/V Receiver input you used when you connected the stereo audio cables. Match the input names for the TV Input and A/V Receiver Input selections.
PAGE 48
Adding IEEE 1394 Devices Automatically, continued Compatible IEEE 1394 Devices It is possible to connect devices to the TV that have IEEE 1394 connectors but are not compatible with the TV or with the NetCommand® control system. Areas of compatibility to consider are: 1. Digital Video Signals The TV is able to decode MPEG2 video. Other types of digital video, such as DV video, provided by some camcorders, must be decoded by the source device and sent to the TV as analog video or S-Video.
PAGE 49
Chapter . . . 4 Device Selection Device Selection Menu ...................................................................................50 PIP Device Selection Menu ............................................................................51 Transport Menu ...............................................................................................51 Channel Selection, Sleep Timer, Audio and Video Buttons........................52 NetCommand Controlled Recordings.....................................
PAGE 50
Device Selection Menu When you press DEVICE on the TV’s remote control, the Device Selection menu (Figure 1) displays. When NetCommand® has not been setup, the Device Selection menu allows you to select an input for viewing. When NetCommand is setup the Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V Receiver, power compatible devices On or Off, and verify the destination of signals.
PAGE 51
PIP Device Selection Menu, Displaying and Using the Transport Menu PIP Device Selection Menu Figure 2 When you press the PIP DEVICE button on the remote control, the PIP Selection menu displays. The PIP Selection menu is similar to the Device Selection menu except the source for the Video Section is the sub picture and the Audio and Connection Sections are not displayed. Use the ADJUST , , or to move the yellow highlight to the Device you want to show in the PIP or POP image then Press ENT(er).
PAGE 52
Channel Selection, Sleep Timer, Audio and Video Buttons Channel Selection For Antenna-A or Antenna-B channels: 1. Enter three numbers (for channel 2, press 002). 2. Press the channel number and ENT(er). Example: for channel 2, press 2, then ENT(er). 3. Enter the channel number and wait four seconds. The TV will change automatically. For Antenna DTV Channels (When Antenna DTV is the current device): 1. Enter two or three numbers for the major channel number.
PAGE 53
NetCommand ® Controlled Recordings Record To Setup Figure 4 Your TV is able to start and stop recordings automatically and send the signals from one external playback device to another external recording device. It is also able to convert digital signals from Antenna DTV and from IEEE 1394 devices to analog signals that can be recorded on NetCommand compatible analog VHS and S-VHS VCRs.
PAGE 54
NetCommand ® Controlled Recordings, continued Record List Screen Figure 5 To view a list of all of your currently programmed recordings, select List from the Record List screen. A maximum of 32 recordings can be scheduled. To cancel a recording on the Record List, press ADJUST or to select the recording, then press CANCEL. To page through the list, press CH or .
PAGE 55
Chapter . . . 5 TV Menu Screen Operations Main Menu Choices ........................................................................................56 Setup Menu ......................................................................................................57 Antenna Menu..................................................................................................58 Time Menu........................................................................................................60 Captions Menu.
PAGE 56
Main Menu Choices Setup V-Chip Lock Add, change, review or delete NetCommand® settings and devices. You can also change the order of icons displayed on the Device Selection menu, select energy mode, turn on or off the transport menu, and select English or Spanish as the language for the menus and onscreen displays. Block or allow programing based upon rating signals sent by the broadcast station, lock by time, or disable or re-enable the front panel buttons. Figure 1 Figure 5 Figure 5.
PAGE 57
Setup Menu Setup Menu Figure 8 Select Setup to perform the functions listed below. Transport Menu The Transport Menu is used by NetCommand® to control VCRs, DVDs, IEEE 1394 AV Disc, digital VCRs, and similar devices. This menu can be turned off if you would rather not have it displayed. The transport buttons on the remote control will continue to operate these devices. Energy Mode Figure 8.
PAGE 58
Antenna Menu: Antenna, Memorize Channels, Channel, Memory and Name Antenna Menu The following Antenna Menu options are available for use on Antenna A, Antenna B or Antenna DTV. You can memorize channels, add or delete channels, and add channels to an SQV (Super Quick View™) list. For Antenna A and Anenna B, you can name channels. Antenna Menu Channel Select Antenna to perform the functions listed below.
PAGE 59
Antenna Menu: SuperQuickView™ (SQV) SQV (SuperQuickView™) Using The Menu Screen Figure 10 SQV (SuperQuickView™) allows you to put together lists of your favorite channels from Antenna A, Antenna B and Antenna DTV. You can store channels in any of the 9 different SQV memory banks. You can also store the same channel in multiple memory banks. Once you have added a channel to an SQV memory, “SQV” and the memory bank number will appear under the tuned channel number on the TV screen. Adding SQV Channels 1.
PAGE 60
Time Menu: Setting the Clock, Manual or Auto Time Menu Setting the Clock (Auto) Select Time to perform the functions listed below. The Clock Setting (Auto) will automatically set the day and time using Extended Data Service (XDS) time data. This data is automatically retrieved from a PBS channel or other channel carrying this service when received on Ant-A or Ant-B. Be aware that some channels may send incorrect time information, this is not a defect in the TV.
PAGE 61
Time Menu: Setting The Timer Timer On/Off Device The timer can be turned to On or Off. When On, you need to select the time to turn On, the day to turn On, the device and the channel to display. At your preselected time, the timer will turn the TV On, and this message will be displayed: “Press a button for the TV to stay on”. Any button on the remote control must be pressed within 5 minutes, or the TV will turn itself Off.
PAGE 62
Captions Menu: Analog and Digital Captions Captions Menu Background Figure 14 Select Captions to perform the functions listed below. For analog channels (Antenna A or Antenna B), broadcasters can send either Standard or Text closed captioning. Standard Closed Captions follows the dialogue of the characters on-screen and displays in a small section of the screen. Text Closed Captions often contain information such as weather or news and covers a large portion of the screen.
PAGE 63
Captions Menu: Digital Captions Settings Appearance Background Figure 15 Closed Captions provider selects the Default options when sending digital closed captions. You may, however, select the Custom option to override and customize Closed Captions appearance. These settings do not apply to analog Closed Captioning converted to digital. To make the digital closed captions easier to read, you can choose the background color.
PAGE 64
V-Chip Lock Menu: Passcode V-Chip Select V-Chip Lock to perform the functions listed below. V-Chip allows you to Block or Allow programs based upon rating signals sent by the broadcaster. The TV comes from the factory with the V-Chip Lock in the Off setting. You can turn the V-Chip on within the V-Chip Menu or you can use the V-CHIP button on the remote control to conveniently turn the V-CHIP on or off.
PAGE 65
V-Chip Lock Menu: V-Chip Definitions V-Chip Signal Information When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press the INFO button on the remote control. Both TV and Movie ratings will display. TV ratings apply to programs and movies developed for TV and may have supplemental blocking by content categories.
PAGE 66
V-Chip Menu: Lock By Time and Front Button Lock Lock By Time Front Button Lock LOCK BY TIME will allow you to lock the entire TV during specific hours. During the Lock Time, you must use your passcode to view the TV. Front Button Lock lets you disable controls on the front panel to prevent anyone from changing settings by accident. 1. Use ADJUST or to select ON or OFF then use ADJUST to move to the Lock Time box.
PAGE 67
A/V Settings Menu: Memory Reset, Settings, Video Mute, Black Enhancement, TV Speakers, Audio 2 Out Audio/Video Figure 21 Select Audio/Video to perform the functions listed below. TV Speakers This selection will turn on or off the TV’s internal speakers. You may select Off when sending the sound through a separate stereo system or surround sound A/V receiver. When NetCommand® is enabled, selecting the A/V Receiver icon from the Device Selection menu automatically turns Off the TV speakers.
PAGE 68
A/V Setting Descriptions: Audio NOTE: The effects of the Audio Settings of Bass, Treble, Balance and Surround affect the sound heard through the TV speakers only. Audio Settings ◊ Bass Enhances or reduces low-pitch sound. ◊ Treble Enhances or reduces high-pitch sound. ◊ Balance Adjusts the level of sound between the left and right speakers. ◊ Surround Creates simulated stereo and surround effects through the TV speakers. Your choices are: • Off: No surround effects.
PAGE 69
A/V Setting Descriptions: Video Video Settings ◊ Contrast Provides a slider to adjust the white-to-black level. Low contrast shows a variety of shades in darker images, while high contrast shows darker images more uniformly black and makes colors appear more vibrant. In most home lighting situations, a medium contrast looks best. High contrast is good for brightly lit environments. ◊ Brightness Provides a slider to adjust the overall brightness of the picture.
PAGE 70
Advanced Menu: Reset Factory Defaults, Convergence Advanced Menu: Convergence Figure 22 Select Advanced to perform the functions listed below. Reset Factory Defaults Menu Figure 23 This allows you to reset the convergence to the original factory settings. The message “Convergence reset completed” will be displayed when the factory defaults have been restored.
PAGE 71
Advanced Menu: Advanced Convergence, Color Balance Advanced Convergence Menu Color Balance After adjusting the Red Convergence and Blue Convergence, you can fine-tune your TV by adjusting the Red and Blue convergence at 64 individual points. Your Mitsubishi TV uses six colors (Magenta, Red, Yellow, Green, Cyan and Blue) to create color balance. You may adjust the intensity of the colors automatically or manually (PerfectColor™) or reset them to the default settings.
PAGE 72
IMPORTANT NOTES WARNING: Do not leave stationary or letterbox images on-screen for extended periods of time. Mix types of pictures shown. Uneven picture tube aging is NOT covered by your warranty. The normal use of a TV should include a mixture of TV picture types. The most frequently used picture types should fill the screen with constantly moving images rather than stationary images or patterns.
PAGE 73
Chapter . . . 6 Special Features NetCommand Controlled Peer-to-Peer Connections .................................74 NetCommand Remote Control Buttons Device Menu, Guide ....................75 Recording on a NetCommand Traditional VCR, A/V Disc Search, Track List Screen.............................................................................................76 Memory Card Playback ..................................................................................77 Device Menu with NetCommand ...........
PAGE 74
NetCommand ® Controlled Peer-to-Peer Connections What is a Peer-to-Peer Connection? Figure 1 A peer-to-peer connection allows the IEEE 1394 devices in your TV network to talk to each other without the further need of TV intervention once the peer-to-peer connection is established. For example, the TV can setup a connection for an A/V Disc or DVCR that sends a recorded program to an IEEE 1394 monitor in another room. NetCommand will establish the connection between the two devices.
PAGE 75
NetCommand Remote Control Buttons: Device Menu, Guide Device Menu Guide While watching a NetCommand compatible traditional IR controlled or an IEEE 1394 device, press DEVICE MENU once or twice to display the menu for that device. • For NetCommand compatible satellite receivers and some cable boxes, GUIDE will display the on-screen programming guide for the receiver or cable box. Press ADJUST , , or and ENT(er) to navigate the displayed Guide.
PAGE 76
Recording on a NetCommand® Traditional VCR, A/V Disc Search, Track List Screen Recording on a NetCommand Traditional VCR Pressing REC (record) on the TV’s remote control will function the same way as pressing the record button on the VCR’s remote control or front panel. To record directly from antenna or cable: 1. Press DEVICE on the TV’s remote to display the Device Selection menu. Highlight the traditional VCR and press POWER to turn on the VCR.
PAGE 77
Memory Card Playback Warning: Some memory cards available on the market are not properly certified for use by the Card Reader. If you experience problems with the reading of your file, please transfer your files to a card from a different manufacturer. Memory Card Slots Inserting a Memory Card Remote Control Buttons for Controlling the Playback 1. Insert a card into a matching card slot on the front of the TV. Be sure to use the correct card slot. Card 1 will accept MultiMediaCard™ and SD Memory Card.
PAGE 78
Memory Card Playback, continued For MP3 or WMA7 Audio Menu: Figure 5 1. Press GUIDE on the remote to display the Playlist. 2. Using ADJUST or to move the highlight to different tracks (CH up/down will change pages of the Playlist). 3. Press PLAY to begin playback. The Playlist menu will be taken down. An asterisk (*) will be next to the song currently playing. from the cards will be sent to the A/V Receiver as analog audio. Digital out is not available.
PAGE 79
Device Menu with Net Command ® NetCommand Compatible Traditional Devices (Analog) When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) REMOTE CONTROL BUTTON A/VReceiver VCR DVD Cable Box/DBS POWER Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) DEVICE MENU n/a n/a n/a n/a GUIDE Changes between Digital and Analog audio Changes VCR inputs n/a Changes antenna inputs (RCA model DTC-100 only) FORMAT n/a n/a Change
PAGE 80
Device Menu with Net Command ®, continued Remote Control Button When Net Command® Compatible Traditional Device is Viewed or Played A/V Receiver VCR DVD Cable/DBS Channel up/down Skip Forward/Backwards Chapter or Track Channel up/down Page up/down when guide showing 0-9 (digits) number functions number functions number functions DEVICE Menu 1st press Transport Menu, 2nd press Setup Menu display CH up/down VOL up/down Volume Up/Down MUTE Mute On/Off QV Last Channel Recall HOME ENTer CANC
PAGE 81
Operation of PIP and POP Picture-In-Picture (PIP) and Picture-Outside-Picture (POP) features allow you to view programming in different ways. While watching the main screen, you can display programs from other channels and other inputs. You can display a single PIP, side-by-side pictures, three POPs, or nine POPs Activating the PIP and POP To turn PIP/POP off, wait at least 10 seconds, and press PIP/POP.
PAGE 82
Display Formats This is a wide screen TV (also known as a 16:9 TV). This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow screen images (called 4:3 aspect ratio) you will encounter. While there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display formats to choose from. Press FORMAT on the TV remote control to cycle through the available display formats.
PAGE 83
Display Formats ��
PAGE 84
Software Updates From time to time, Mitsubishi may offer software updates to expand the features or operation of this TV. When these updates are available they will be announced on our web site, Mitsubishi-tv.com. If you return your Owner’s registration card, with your model and serial number, you may receive written notification of available software updates.
PAGE 85
Appendix A: Bypassing the V-Chip Lock: Lock Bypass Instructions Have Been Filed for Future Reference Bypassing the V-Chip Lock After you set the lock, you need your passcode to view a V-Chip locked program, view the locked TV, cancel the lock, or enter the V-Chip Lock menus. If you forget your passcode, you can view the locked TV without entering your passcode. This is done by pressing the number 9 and QV buttons on the TV remote control at the same time, when your passcode is requested.
PAGE 86
This page intentionally blank 86
PAGE 87
Appendix B: High Definition Input Connection Compatibility Component-1 and Component-2 Inputs These inputs are compatible with component video signals from standard DVD players and other equipment sending a standard NTSC component video signal (480i). These inputs are also compatible with newer DVD players sending 480p and are compatible with signals from digital TV receivers that send 1080i component video signals. VGA Input This input will accommodate most computers capable of supporting a VGA monitor.
PAGE 88
Appendix C:Remote Control Programming Codes To Program the Remote to Control “Other” Brands of Audio and Video Products 1. Move the slide switch at the top of the remote to the product you want to control. 2. Press and hold the POWER button on the remote control. 3. Enter the first three digit code listed for your equipment, and then release the POWER button on the remote control. 4. Point the remote control at the equipment and press the POWER button.
PAGE 89
Appendix C: Remote Control Programming Codes DVD Players Mitsubishi 003 Aiwa 261, 274 Apex 266, 283 Bose 286 Denon 250, 273 Ferguson 251 GE/RCA/Proscan 251, 256 Harman Kardon 282, 288 Hitachi 270 JVC 257 Kenwood 271, 289 Mintek 285 Next Base 284 Normande 251 Onkyo 267, 280 Oritron 263, 268 Paite 262 Panasonic 250 Philips/Magnavox 258, 253, 272, 290 Pioneer 252 Saba 251 Sampo 263 Samsung 261 Sanyo 275 Sharp 260 SMC 275 Sylvania 264 Sony 254, 278, 279 Thompson 251 Toshiba 253, 287 Venturer 281 Vialta 277 Wave
PAGE 90
Appendix C: Remote Control Programming Codes After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed. If the TV position has not been programmed to control NetCommand and you enter a code from the A/V Receiver chart while the slide switch is set to TV, the volume and mute functions change to match the A/V receiver. This is useful when using an A/V Receiver with the TV all the time.
PAGE 91
Appendix C: Remote Control Programming Codes When your remote control has been programmed to operate another manufacturer’s product, the function performed on each layer can vary.
PAGE 92
Appendix D: On Screen Information Displays When you turn on the TV, change Devices, change Channels or when you press the INFO button on the remote control the TV will display the current status. Below are the most common displays; please note that seldom or never do all of the different status indicators appear at the same time. Analog Antenna or Devices 1. 2. 6. 7. 8. 9. 10.
PAGE 93
Appendix E: NetCommand® Specialized Device Keys A/V CABLE RECEIVER or DBS VCR DVD LEARNING SCREEN CHECKBOX NAME Function Name on TV Remote X X X X Power* Power On or Power On/Off POWER** X X X X Power (Off)* Power Off POWER** X Volume Up Volume Up VOL X Volume Down Volume Down VOL X Mute Mute MUTE X Analog to Digital* Analog/Digital Switch GUIDE** X Digital to Analog* Digital/Analog Switch GUIDE** X Input (1-7) AVR Input Select Automatic (when device is selected) X
PAGE 94
Appendix F: Cleaning and Service This TV is very heavy! Exercise extreme care when moving TV as foreign material may become embedded in the castor wheels which could damage wood or other delicate flooring. Cleaning Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines: First, turn off the TV and unplug the power cord from the power outlet.
PAGE 95
Appendix G: Diamond Shield™ Removal for Models WS-48513, WS-48613, WS-55513, WS-55613, WS-65513, WS-65613 and WS-73513 The instructions below will lead you through the Diamond Shield removal process for models WS-48513, WS-48613, WS-55513, WS-55613, WS-65513, WS-65613 and WS-73513. The Diamond Shield for these models comes installed by the factory. You will need to remove: (2) molding clips (1) Diamond Shield™ 1. Remove the side clips by pressing them out of the opening, starting at a corner.
PAGE 96
Appendix G: Diamond Shield™ Installation for Models WS-55813, WS-65713, WS-65813 and WS-73713 The instructions below will lead you through the Diamond Shield installation process. Included in the Diamond Shield package are the following items: For models WS-55813, WS-65713, WS-65813 and WS-73713 (1) Diamond Shield™ (2) molding clips 1. Carefully remove the Diamond Shield™ from the protective packaging. Wipe off any dust with a lintfree cloth. Do not use any cleaners on the anti-glare Diamond Shield™. 2.
PAGE 97
Appendix H: Cabinet Separation for Models WS-65513, WS-65613 ��
PAGE 98
Appendix H: Cabinet Separation for Model WS-65713, WS-73513, WS-73713 For Mitsubishi Dealers and Service Personnel Only The Mitsubishi TV models WS-65713, WS-73513 and WS-73713 cabinets are assembled in two pieces. These pieces may be separated to allow for easier delivery and set up. The instructions below show how to safely separate and reattach the cabinet. This TV weighs over 320 lbs and has many sensative components.
PAGE 99
Appendix H: Cabinet Separation for Model WS-65813 ��
PAGE 100
Problem Possible Solution 1. The TV remote control does not work. • Check that the batteries are installed correctly. • Check that the selected switch is set to “TV”. • Be no further than 20 feet from the TV when using the remote control. • Program the remote control to operate the TV (Appendix C). 2. The TV takes several seconds to respond. • It is normal for digital channels to take longer to tune in. • Press ENT(er) after a channel number to avoid delays. • Use the three digit number, i.
PAGE 101
Problem Possible Solution 18. When viewing a stopped VCR, white lines are rolling on the screen. • Turn off video mute for the VCR. • Begin playing the tape. • Change the VCR input to the antenna input. 19. TV turned itself Off and the light on the Front Panel started to blink. • Momentary power fluctuation caused the TV to turn off to prevent damage. Wait for the green light to stop flashing and turn On again. • If the TV does not stay turned On, use the System Reset button.
PAGE 102
Problem Possible Solution 29. Excessive digital artifacts. • The IEEE 1394 cable is too long (15 feet between devices is the maximum length). • There may be a slow device in the middle of the IEEE 1394 network. Move the slow devices to the end so that connections for faster devices do not pass through them. 30. Cannot see a picture from a DV Camcorder. • Go to Device Selection menu and select analog connection. • Connect the DV Camcorder to analog input (for example,Input-3).
PAGE 103
Problem Possible Solution 41. An IEEE 1394 device has been plugged in but does not appear in the Device Selection menu (not discovered). • The IEEE 1394 connection to the TV or another device is not secure or is loose. • The IEEE 1394 device is not powered on. • A device in the IEEE 1394 chain is not powered on - turn on all the devices. • The device discovery can take as long as a minute to initiate. • IEEE 1394 cable is too long (maximum of 15 feet between devices).
PAGE 104
Index A A/V (Audio Video) Memory Reset 67 Receiver, Connecting 21 A/V Disc Search 76 A/V Receiver Connecting 21 with NetCommand 37-39 Advanced Menu 56, 70-71 Advanced Convergence 71 Convergence 70 Reset Factory Defaults 70 Antenna Menu 56, 58-59 Appendixes A: Bypassing the V-Chip Lock 85 B: High Definition Input Connection Compatibility 87 C: Remote Control Programming Codes 88-91 D: On Screen Information Displays 92 E: NetCommand Specialized Device Keys 93 F: Cleaning and Service 94 G: Diamond Shield™ Remo
PAGE 105
L Language Menu 35, 57 Lock by Time 66 M Memorize Channels 58 Memory 58 Memory Cards Playback 77-78 Slots 10-11 Menus Main (also see individual topic) 31, 56-71 NetCommand 33-54, 57 N Name Channels 58 NetCommand® Adding an A/V Receiver 37-39 Devices 40-43 IEEE 1394 Devices Automatically 47-48 Changing Device 44 Connecting External Devices 16 Controlled Recordings 53-54 Deleting Device 44 Device Menu 75, 79 Device Selection Menu 50-51 Editing 34, 40-43 Guide button 75 Initial Setup 33, 35-36 Peer-to-Peer
PAGE 106
Demo Mode This TV has a demo mode for use in a retail store. To turn On/Off, press the following buttons in sequence: MENU, 0, QV, 0 LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Manufactured under license from Dolby Laboratories.
PAGE 107
Mitsubishi Projection TV Limited Warranty MITSUBISHI PROJECTION TELEVISION LIMITED WARRANTY MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this television that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material: a. Parts. The lenticular (i.e. front picture) screen and/or the DiamondShield™ is warranted against defects in materials and workmanship for a period of 30 days.
PAGE 108
MITSUBISHI TV SOFTWARE END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software preinstalled and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
PAGE 109
Connection: Helpful Hints Q My VCR (or other device) does not have two sets of stereo audio outputs; how can I connect this device’s audio to both the TV and the A/V Receiver? A. There are two solutions: 1. Connect the single set of stereo audio outputs to the TV only. Use the Edit NetCommand® feature to “Change” the setup of this device.
PAGE 110
If you have questions regarding your television, call Consumer Relations at (800) 332-2119, or email us at M D E A s e r v i c e @ b i g s c re e n . m e a . c o m To order replacement or additional remote controls or owner’s guides call (800) 553-7278 or visit our website at w w w.m i t s u b i s h i -t v.c o m © 2003 Mitsubishi Digital Electronics America, Inc. 871D370B10 Written and Printed in the U.S.