3D Starter Pack MODEL 3DC-1000 OWNER’S GUIDE Features • • • • Converts 3D video originating in several popular formats to checkerboard format for display on your 3D or 3D-ready Mitsubishi television. Processes side-by-side, top-and-bottom, and frame-packing 3D (e.g., Blu-ray 3D) formats. Passes 2D images unaltered for normal display. Includes two pairs of active-shutter 3D glasses and matching IR emitter.
Important Safety Instructions 1) 2) 3) 4) 5) 6) 7) 8) 9) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Only use attachments/accessories specified by the manufacturer. Refer all servicing to qualified service personnel.
Notes on 3D video and TV compatibility The Mitsubishi 3D Adapter, Model 3DC-1000, may be used to display 3D content only when connected to a Mitsubishi 3D Ready TV or a Mitsubishi 3D TV. A 3D source device coupled with the Mitsubishi 3D Adapter is required to support display of 3D games, 3D broadcasts from terrestrial/cable/satellite and 3D Blu-ray disc content. Mitsubishi 738 and 838 series televisions: -- Mitsubishi 738 and 838 series televisions loaded with software version 12.
3D Adapter Battery Installation The remote control requires one CR2025 lithium battery. To remove the battery, press on the retaining clip. 1 2 Emitter 1. Remove the cover. 2. Insert the battery, positive side up. Be sure the retaining clip holds the battery securely. 3. Reinstall the cover. 3D STATUS IR Sensor POWER 3D MODE Adapter 3D MODE POWER POWER Controls and Indicators Remote Control POWER Light Lit when power is on. 3D STATUS Light Lit during 3D signal processing.
Lithium Battery Safety This product uses CR2025 Li/MnO2 lithium coin batteries. WARNING: Lithium coin cell batteries pose a serious risk of injury if ingested. Keep cells out of reach of children. If ingested immediately contact a physician or the National Poison Center at 202-625-3333. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type (CR2025). CAUTION: Risk of fire and burns.
Connecting the Adapter Connecting a Single 3D Video Source • • • Power off all devices prior to connecting the Adapter. If the device was in use prior to adding the Adapter, use the same TV input if possible. On an 833 series TV, the input must be named Game. Step 1. HDMI OUT 3D GLASSES EMITTER OUT AC power adapter (provided) 5V DC 2A 3D GLASSES EMITTER IN HDMI IN 5V DC 2A Step 2.
Using the Adapter 1. Position the emitter where there will be a 2. clear path to the 3D glasses. Power on the TV, the 3D video device, and the 3D glasses. Note: The 3D video device must be powered on before the 3D Adapter can power on. 3. If the 3D Adapter does not power on automatically when you power 4. 5. 6. 7. on the 3D video device, press the POWER button. If the New Input Found screen displays, assign a name to the input. If you have an 833 series TV, name the input Game.
3D Glasses 3D active LCD shutter glasses enable you to view 3D images when used with the matching IR emitter and a compatible 3D-ready TV. Power Button Battery Cover LCD Shutter Lens LED Indicator Emitter LED Lit when TV is in 3D mode. Battery Installation • • • Each pair of glasses requires one CR2025 lithium battery. A continuously blinking red LED indicates low battery power. Install a new battery. See lithium-battery safety information at the front of this booklet. Open the cover.
Using the 3D Glasses 3D Glasses Operation 1. Turn on 3D Mode in the TV and 3D source device. 2. Press the POWER button on the glasses to turn on the glasses. 3. When the 3D program is complete, turn off 3D mode in the TV and 3D source device and turn off the glasses. On Operating Range Be from 5 to 20 feet away. Press POWER button. The red LED will light for three seconds. Off 5 ft. 20 ft. 50° 50° Hold POWER button for about two seconds. Red LED will blink three times.
Cleaning Instructions • • • • To avoid scratching the glasses, use only standard glasses lens cleaning cloth, microfiber cloth, or a soft non-scratching cloth such as cotton flannel. Make sure the cloth is clean and free of any foreign material that may scratch the glasses. Cloths pre-moistened with cleaning solutions designed specifically for eye glasses can be used, however, do not spray solutions directly on the glasses. DO NOT spray any cleaner directly onto the any surface of the glasses.
3D Safety Requirements • 3D Glasses are NOT designed as sunglasses or safety glasses and do not provide protection. 3D glasses should be worn only when viewing 3D material. • Do not wear the wireless glasses in any situations that require unimpaired visual perception. • Children under the age of 5 should not view 3D programming. Under normal conditions, 3D viewing is safe for your movies or games. Some people may experience discomfort, however.
Mitsubishi Model 3DC-1000 3D Starter Kit Limited Warranty for U.S.A. MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC. (“MEVSA”) warrants as follows to the original purchaser of this 3D Starter Kit from an authorized MITSUBISHI Audio/Video Dealer, should the adapter, glasses, IR emitter, remote control or included accessories prove defective by reasons arising from improper workmanship and/or material: a. Length of Warranty.
service center; physical abuse to or misuse of the product (including any failure to carry out any maintenance as described in the Owner’s Guide or any product damaged by excessive physical or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors beyond the reasonable control of MEVSA, such as power surge damage caused by e
Mitsubishi Model 3DC-1000 3D Starter Kit Limited Warranty for Canada This limited warranty is valid only for products purchased, used and serviced in Canada. MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC. (“MEVSA”) warrants as follows to the original purchaser of this 3D Starter Kit from an authorized MITSUBISHI Audio/Video Dealer, should the adapter, glasses, IR emitter, remote control or included accessories prove defective by reasons arising from improper workmanship and/or material: a.
separately purchased glasses and IR Emitter for warranty details), cosmetic damage or any other damage where such damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any maintenance as described in the Owner’s Guide or any product damaged by excessive physical or electrical stress); any products that have had a serial numb
For questions: -- Visit our website at www.mitsubishi-tv.com. -- E-mail us at TVSupport@mevsa.com. -- Call Consumer Relations at 800-332-2119 for operational or connection assistance. To order replacement or additional remote controls or other accessories, visit our website at www.mitsuparts.com or call 800-553-7278. 3DC-1000 © 2011 Mitsubishi Electric Visual Solutions America, Inc.