2020 OWNER’S MANUAL Renegade
VEHICLES SOLD IN CANADA With respect to any vehicles sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation.
20_BV_OM_EN_US_t.book Page 1 TABLE OF CONTENTS 1 INTRODUCTION ................................................................................................................................................................................13 1 2 GETTING TO KNOW YOUR VEHICLE .........................................................................................................................................16 2 3 GETTING TO KNOW YOUR INSTRUMENT PANEL ..................................................
20_BV_OM_EN_US_t.book Page 2 2 INTRODUCTION INTRODUCTION ..............................................................13 HOW TO USE THIS MANUAL .......................................14 Essential Information ....................................................14 Symbols...........................................................................14 ROLLOVER WARNING ...................................................14 WARNINGS AND CAUTIONS .......................................
20_BV_OM_EN_US_t.book Page 3 3 DOORS .................................................................................32 Manual Door Locks.......................................................32 Power Door Locks ........................................................34 Keyless Enter-N-Go — Passive Entry (If Equipped) ..................................................................34 Automatic Unlock On Exit Feature — If Equipped................................................................
20_BV_OM_EN_US_t.book Page 4 4 INTERIOR LIGHTS ............................................................66 Courtesy Lights..............................................................66 Cargo Area Lights .........................................................71 WIPERS AND WASHERS ................................................71 Front Wiper Operation .................................................72 Rain Sensing Wipers — If Equipped .........................72 Rear Wiper Operation .
20_BV_OM_EN_US_t.book Page 5 5 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER................................................127 Instrument Cluster Descriptions ...............................128 INSTRUMENT CLUSTER DISPLAY .............................130 Instrument Cluster Display Location And Controls.........................................................................130 Oil Change Reset .........................................................
20_BV_OM_EN_US_t.book Page 6 6 STARTING AND OPERATING STARTING THE ENGINE ..............................................242 Tip Start Feature .........................................................242 If Engine Fails To Start ...............................................243 Cold Weather Operation ............................................244 Extended Park Starting...............................................244 After Starting — Warming Up The Engine .............
20_BV_OM_EN_US_t.book Page 7 7 ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED..................................................................... 275 Adaptive Cruise Control (ACC) Operation.............277 To Activate/Deactivate ..............................................277 Activating Adaptive Cruise Control (ACC) ............278 To Set A Desired ACC Speed.....................................279 To Cancel ......................................................................
20_BV_OM_EN_US_t.book Page 8 8 REAR BACK UP CAMERA ............................................355 ADDING FUEL .................................................................357 VEHICLE LOADING ......................................................360 Certification Label .......................................................360 TRAILER TOWING ..........................................................362 Common Towing Definitions ....................................
20_BV_OM_EN_US_t.book Page 9 9 REFUELING IN EMERGENCY — IF EQUPPIED ....... 434 IF YOUR ENGINE OVERHEATS ...................................435 GEAR SELECTOR OVERRIDE ......................................436 FREEING A STUCK VEHICLE ......................................437 TOWING A DISABLED VEHICLE ...............................439 Front Wheel Drive (FWD) ..........................................440 Four Wheel Drive (4WD) ...........................................
20_BV_OM_EN_US_t.book Page 10 10 STORING THE VEHICLE................................................495 BODYWORK......................................................................496 Protection From Atmospheric Agents......................496 Body And Underbody Maintenance......................... 496 Preserving The Bodywork..........................................497 INTERIORS .......................................................................498 Seats And Fabric Parts .............
20_BV_OM_EN_US_t.book Page 11 11 MULTIMEDIA UCONNECT SYSTEMS ................................................... 511 DRAG & DROP MENU BAR .........................................511 CYBERSECURITY ............................................................ 512 UCONNECT SETTINGS..................................................513 Customer Programmable Features — Uconnect 3 Settings .....................................................514 Customer Programmable Features — Uconnect 4 Settings ..........
20_BV_OM_EN_US_t.book Page 12 12 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE .....................................................592 Prepare For The Appointment .................................. 592 Prepare A List ..............................................................592 Be Reasonable With Requests....................................592 IF YOU NEED ASSISTANCE .........................................592 FCA US LLC Customer Center............................
20_BV_OM_EN_US_t.book Page 13 13 INTRODUCTION 1 INTRODUCTION Dear Customer, congratulations on selecting your new vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality. This is a specialized utility vehicle. It can go places and perform tasks that are not intended for conventional passenger vehicles. It handles and maneuvers differently from many passenger vehicles both on-road and off-road, so take time to become familiar with your vehicle.
20_BV_OM_EN_US_t.book Page 14 14 INTRODUCTION the trim level, engine, and version that you have purchased. Any content introduced throughout the Owner's Information, that may or may not be applicable to your vehicle, will be identified with the wording "If Equipped". All data contained in this publication are intended to help you use your vehicle in the best possible way. FCA US LLC aims at a constant improvement of the vehicles produced.
20_BV_OM_EN_US_t.book Page 15 INTRODUCTION 15 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper1 ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information. Observe all Warnings and Cautions.
20_BV_OM_EN_US_t.book Page 16 16 GETTING TO KNOW YOUR VEHICLE KEYS Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system. The Remote Keyless Entry system consists of a key fob and Keyless Enter-N-Go feature if equipped. NOTE: The key fob may not be found if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal.
20_BV_OM_EN_US_t.book Page 17 GETTING TO KNOW YOUR VEHICLE 17 To Unlock The Doors And Liftgate Push and release the unlock button on the key fob once to unlock the driver's door or twice within five seconds to unlock all doors and the liftgate. All doors can be programmed to unlock on the first push of the unlock button. Refer to “Uconnect Settings” in “Multimedia” for further information.
_BV_OM_EN_US_t.book Page 18 18 GETTING TO KNOW YOUR VEHICLE 1st Push Of Key Fob Unlock Button This feature lets you program the system to unlock either the driver's door or all doors on the first push of the unlock button on the key fob. To change the current setting, refer to “Uconnect Settings” in “Multimedia” for further information. NOTE: If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go — Passive Entry” in “Doors” in this chapter for further information.
20_BV_OM_EN_US_t.book Page 19 GETTING TO KNOW YOUR VEHICLE 19 1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your thumb and pull the emergency key out with your other hand. 2. Separate the key fob halves using the tip of the emergency key, a #2 flat blade screwdriver, or a coin and gently pry the two halves of the key fob apart. Make sure not to damage the seal during removal.
20_BV_OM_EN_US_t.book Page 20 20 GETTING TO KNOW YOUR VEHICLE Separating Case With A Coin Key Fob Battery Replacement 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery. When replacing the battery, match the (+) sign on the battery to the (+) sign on the inside of the battery clip, located on the back cover. Avoid touching the new battery with your fingers.
20_BV_OM_EN_US_t.book Page 21 GETTING TO KNOW YOUR VEHICLE Programming Additional Key Fobs Programming the key fob may be performed by an authorized dealer. Request For Additional Key Fobs NOTE: Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle. WARNING! • Always remove the key fobs from the vehicle and lock all doors when leaving the vehicle unattended.
20_BV_OM_EN_US_t.book Page 22 22 GETTING TO KNOW YOUR VEHICLE Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Development applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
20_BV_OM_EN_US_t.book Page 23 GETTING TO KNOW YOUR VEHICLE 23 RUN • Driving position. • All the electrical devices are available. 2 NOTE: The vehicle will not start if the key fob is located inside the cargo area and the liftgate is opened. WARNING! • When leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle. START/STOP Ignition Button The push button ignition can be placed in the following positions: OFF • The engine is stopped.
20_BV_OM_EN_US_t.book Page 24 24 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. CAUTION! An unlocked vehicle is an invitation for thieves. Always remove key fob from the vehicle and lock all doors when leaving the vehicle unattended. NOTE: For further information, refer to "Starting The Engine," in "Starting And Operating".
20_BV_OM_EN_US_t.book Page 25 GETTING TO KNOW YOUR VEHICLE All of the following conditions must be met before the engine will remote start: • Gear Selector in PARK • Doors closed • Hood closed 25 WARNING! (Continued) • Keep key fobs away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
20_BV_OM_EN_US_t.book Page 26 26 GETTING TO KNOW YOUR VEHICLE To Enter Remote Start Mode Push and release the Remote Start button on the key fob twice within five seconds. The vehicle doors will lock, the turn signals will flash twice, and the horn will chirp. Then the engine will start, and the vehicle will remain in the Remote Start mode for a 15 minute cycle. NOTE: • If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.
20_BV_OM_EN_US_t.book Page 27 GETTING TO KNOW YOUR VEHICLE 27 Remote Start Comfort Systems — If Equipped General Information When Remote Start is activated, the heated steering wheel and driver heated seat features will automatically activate when ambient temperature is less than 40°F (4.4°C). These features will stay on through the duration of Remote Start.
20_BV_OM_EN_US_t.book Page 28 28 GETTING TO KNOW YOUR VEHICLE La operación de este equipo está sujeta a las siguientes dos condiciones: 1. es posible que este equipo o dispositivo no cause interferencia perjudicial y 2. este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
20_BV_OM_EN_US_t.book Page 29 GETTING TO KNOW YOUR VEHICLE CAUTION! The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection. All of the key fobs provided with your new vehicle have been programmed to the vehicle electronics. Key Programming Key fob programming is performed at an authorized dealer.
20_BV_OM_EN_US_t.book Page 30 30 GETTING TO KNOW YOUR VEHICLE General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: FCC ID: RX2TCUFCA025N IC: 4983A-TCUFCA02SN This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
20_BV_OM_EN_US_t.book Page 31 GETTING TO KNOW YOUR VEHICLE VEHICLE SECURITY ALARM — IF EQUIPPED rior zone. Refer to "Doors" in this chapter for further information. • Push the lock button on the key fob. The vehicle security alarm monitors the vehicle doors, hood, liftgate, and the Keyless Enter-N-Go — Ignition for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled.
20_BV_OM_EN_US_t.book Page 32 32 GETTING TO KNOW YOUR VEHICLE The vehicle security alarm is designed to protect your vehicle. However, you can create conditions where the system will give you a false alarm. If one of the previously described arming sequences has occurred, the vehicle security alarm will arm, regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle security alarm.
20_BV_OM_EN_US_t.book Page 33 GETTING TO KNOW YOUR VEHICLE To unlock the driver’s door, insert the emergency key into the driver exterior door lock cylinder and turn to the left to unlock the driver's door. 33 WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always remove the key fob from the vehicle and lock your vehicle.
20_BV_OM_EN_US_t.book Page 34 34 GETTING TO KNOW YOUR VEHICLE Power Door Locks A power door lock switch is located on each of the front door trim panels. Use this switch to lock or unlock the doors, liftgate and fuel door. NOTE: The key fob may not be able to be detected by the vehicle keyless-go system if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal and prevent the keyless-go system from starting the vehicle.
20_BV_OM_EN_US_t.book Page 35 GETTING TO KNOW YOUR VEHICLE • The key fob may not be able to be detected by the vehicle’s passive entry system if it is located next to a mobile phone, laptop or other electronic device; these devices may block the key fob’s wireless signal and prevent the passive entry system from locking/unlocking the vehicle. To Unlock From The Driver's Side With a valid Passive Entry key fob within 5 ft (1.
20_BV_OM_EN_US_t.book Page 36 36 GETTING TO KNOW YOUR VEHICLE To Lock The Vehicle’s Doors And Liftgate With one of the vehicle’s Passive Entry key fobs within 5 ft (1.5 m) of the driver or passenger front door handles, push the door handle lock button to lock all four doors. Do NOT grab the door handle when pushing the door handle lock button. This could unlock the door(s). DO NOT Grab The Door Handle When Locking NOTE: • The Passive Entry system will not operate if the key fob battery is depleted.
20_BV_OM_EN_US_t.book Page 37 GETTING TO KNOW YOUR VEHICLE Preventing Inadvertent Locking Of Passive Entry Key Fob In Vehicle (FOBIK-Safe) To minimize the possibility of unintentionally locking a Passive Entry key fob inside your vehicle, the Passive Entry system is equipped with an automatic door unlock feature. FOBIK-Safe only executes in vehicles with Passive Entry. There are three situations that trigger a FOBIK-Safe search in any Passive Entry vehicle: 1.
20_BV_OM_EN_US_t.book Page 38 38 GETTING TO KNOW YOUR VEHICLE To Unlock/Enter The Liftgate The liftgate Passive Entry unlock feature is built into the electronic liftgate release. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the Electronic Liftgate release to open with one fluid motion. To Lock The Liftgate • If “Unlock All Doors 1st Press” is programmed in the instrument cluster display, if equipped, only the liftgate will unlock when you push the Electronic Release.
20_BV_OM_EN_US_t.book Page 39 GETTING TO KNOW YOUR VEHICLE 39 Emergency Unlocking Driver Door If the key fob battery is low or depleted, the emergency key can be used to unlock the driver side door lock cylinder. 2 To release the emergency key, proceed as follows: 1. Slide the emergency key release button to the side. 2. Remove the emergency key from the key fob with Remote Control housing.
20_BV_OM_EN_US_t.book Page 40 40 GETTING TO KNOW YOUR VEHICLE WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the gear selector.
20_BV_OM_EN_US_t.book Page 41 GETTING TO KNOW YOUR VEHICLE NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Automatic Unlock On Exit Feature — If Equipped If Auto Unlock is enabled, this feature will unlock all the doors when any door is opened if the vehicle is stopped and in PARK. Refer to “Uconnect Settings” in “Multimedia” for further information.
20_BV_OM_EN_US_t.book Page 42 42 GETTING TO KNOW YOUR VEHICLE Child Locks To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with a Child-Protection Door Lock system. To use the system, open each rear door, use a flat blade screwdriver (or emergency key) and rotate the dial to the lock or unlock position.
20_BV_OM_EN_US_t.book Page 43 GETTING TO KNOW YOUR VEHICLE SEATS 43 Manual Front Seats Seats are a part of the Occupant Restraint System of the vehicle. 2 WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
20_BV_OM_EN_US_t.book Page 44 44 GETTING TO KNOW YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured. Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest.
20_BV_OM_EN_US_t.book Page 45 GETTING TO KNOW YOUR VEHICLE Split Rear Seats The split rear seat has the ability to fold flat which increases the storage of the rear cargo area. NOTE: • Prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and positioned forward, this will allow the rear seat to fold down easily. • Prior to folding the rear seat, you must secure the rear armrest in the upright position.
20_BV_OM_EN_US_t.book Page 46 46 GETTING TO KNOW YOUR VEHICLE Partial Enlargement Of The Cargo Area Enlargement of the left side of the cargo area allows you to carry a single passenger on the right side of the rear seat, while the enlargement of the right side allows you to carry two passengers. Proceed as follows: 1. Remove the rear shelf (if equipped). Refer to “Cargo Area Features” in “Liftgate” in this chapter for details. 2. Fully lower the rear seat head restraints. 3.
20_BV_OM_EN_US_t.book Page 47 GETTING TO KNOW YOUR VEHICLE 47 Seatback Repositioning NOTE: If interference from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its proper position. 2 1. Move the seat belts to the seat belt guides on the top edge of the seat to ensure the seatbacks properly latch. 2. Lift the seatbacks, pushing them back until they lock on both the latches. Verify the red notches are no longer visible on the release lever.
20_BV_OM_EN_US_t.book Page 48 48 GETTING TO KNOW YOUR VEHICLE Power Adjustment (Front) — If Equipped Adjusting The Seat Forward Or Rearward The power seat controls are located on the outboard side of the seat, close to the floor. The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward. The seat will move in the direction of the switch. Release the switch when the desired position has been reached.
20_BV_OM_EN_US_t.book Page 49 GETTING TO KNOW YOUR VEHICLE Reclining The Seatback The angle of the seatback can be adjusted forward or rearward. Push the recline switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position is reached. WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death.
20_BV_OM_EN_US_t.book Page 50 50 GETTING TO KNOW YOUR VEHICLE Heated Seats — If Equipped Auto Comfort Systems — If Equipped The heated seat buttons are located in your vehicle’s touchscreen or on the instrument panel. In vehicles equipped with Auto On Comfort, when turning on the vehicle the driver’s heated seat will automatically turn on when temperatures are below 40°F (4.4°C). You can choose between two heating levels: • Press the heated seat button once to turn the HI setting on.
20_BV_OM_EN_US_t.book Page 51 GETTING TO KNOW YOUR VEHICLE 51 Unfolding The Rear Armrest 40/20/40 Pull the rear armrest tab to release it from the seat and pull forward. 2 Fold Center Armrest Forward The center part of the rear seat can also be used as rear armrest with cupholders.
20_BV_OM_EN_US_t.book Page 52 52 GETTING TO KNOW YOUR VEHICLE HEAD RESTRAINTS Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. WARNING! Rear Armrest With Cupholders WARNING! Be certain that the seatback is securely locked into position.
20_BV_OM_EN_US_t.book Page 53 GETTING TO KNOW YOUR VEHICLE Front Head Restraints Your vehicle is equipped with front driver and passenger head restraints. To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment button, located at the base of the head restraint, and push downward on the head restraint. 53 NOTE: The head restraints should only be removed by qualified technicians, for service purposes only.
20_BV_OM_EN_US_t.book Page 54 54 GETTING TO KNOW YOUR VEHICLE Rear Head Restraints Your vehicle is equipped with two outboard head restraints and one center head restraint for its rear passengers. The rear head restraints can be raised or lowered. When the center seat is being occupied, the head restraint should be in the raised position. When there are no occupants in the center seat, the head restraint can be lowered for maximum visibility for the driver.
20_BV_OM_EN_US_t.book Page 55 GETTING TO KNOW YOUR VEHICLE STEERING WHEEL Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located below the steering wheel at the end of the steering column. 55 desired. To lengthen or shorten the steering column, pull the steering wheel outward or push it inward as desired.
20_BV_OM_EN_US_t.book Page 56 56 GETTING TO KNOW YOUR VEHICLE Auto Comfort Systems — If Equipped MIRRORS In vehicles equipped with Auto On Comfort, when turning on the vehicle the heated steering wheel will automatically turn on when temperatures are below 40°F (4.4°C). Inside Day/Night Mirror Auto Comfort Systems can be enabled or disabled. Refer to “Uconnect Settings” in “Multimedia” for further information.
20_BV_OM_EN_US_t.book Page 57 GETTING TO KNOW YOUR VEHICLE 57 NOTE: The mirror will automatically release in the event of heavy contact with a passenger. Auto Dimming Mirror — If Equipped 2 This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
20_BV_OM_EN_US_t.book Page 58 58 GETTING TO KNOW YOUR VEHICLE Outside Mirrors Power Adjustment Mirrors — If Equipped The power mirror switch is located on the driver’s door panel. To adjust the mirror, rotate the mirror selection switch to the left or to the right and then push the mirror adjustment switch in the four directions indicated by arrows. NOTE: • To adjust the power mirrors, the ignition must be in the ON/RUN position.
20_BV_OM_EN_US_t.book Page 59 GETTING TO KNOW YOUR VEHICLE 59 Manual Adjustment Mirrors — If Equipped Folding Mirror To adjust the exterior mirrors, push the corners of the mirrors till desired alignment is obtained. The exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, normal and full rearward.
20_BV_OM_EN_US_t.book Page 60 60 GETTING TO KNOW YOUR VEHICLE Power Folding/Unfolding Mirrors — If Equipped Illuminated Vanity Mirrors — If Equipped Push the mirror fold/unfold switch briefly to fold or unfold the exterior mirrors. An illuminated vanity mirror is located on each sun visor. To use the mirror, rotate the sun visor down and swing the mirror cover upward. The lights will turn on automatically. Closing the mirror cover will turn the light off.
20_BV_OM_EN_US_t.book Page 61 GETTING TO KNOW YOUR VEHICLE 61 EXTERIOR LIGHTS Daytime Running Lights (DRLs) — If Equipped Headlights The Daytime Running Lights (DRLs), if enabled through Uconnect Settings, will turn on when the instrument cluster is on and remain on unless the headlights are turned on or 2 the instrument cluster is switched off. The headlight switch is located on the left side of the instrument panel.
20_BV_OM_EN_US_t.book Page 62 62 GETTING TO KNOW YOUR VEHICLE High Beams Flash-To-Pass To turn on the high beam headlights, push the turn signal lever forward (toward the front of the vehicle) and an indicator will illuminate in the cluster. To turn off the high beams, pull the turn signal lever rearward (toward the rear of the vehicle). You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you.
20_BV_OM_EN_US_t.book Page 63 GETTING TO KNOW YOUR VEHICLE Light Sensor The light sensor is equipped with an infrared LED, located on the windshield. It detects changes in light intensity outside the vehicle, based on the sensitivity of light set by using the menu on the display or on the Uconnect system. The higher the sensitivity, the lesser the amount of external light required for controlling the lighting.
20_BV_OM_EN_US_t.book Page 64 64 GETTING TO KNOW YOUR VEHICLE Parking Lights Headlight Delay Deactivation Rotate the headlight switch to the first detent to turn on the parking lights. The parking light indicator in the instrument cluster display will illuminate. The feature is disabled by turning on the headlights, the parking lights or by placing the ignition in the RUN position.
20_BV_OM_EN_US_t.book Page 65 GETTING TO KNOW YOUR VEHICLE An indicator light in the instrument cluster illuminates when the fog lights are turned on. NOTE: The fog lights will operate with the low beam headlights or parking lights on. Selecting the high beam headlights will turn off the fog lights. Cornering Lights The cornering lights are a feature to improve visibility at night while turning the vehicle.
20_BV_OM_EN_US_t.book Page 66 66 GETTING TO KNOW YOUR VEHICLE INTERIOR LIGHTS Courtesy Lights Interior Lights Dimmer Switch Rotate the ambient dimmer control upward or downward to increase or decrease the brightness of the ambient light located in the overhead console, door handle lights, lower instrument panel lights, door map pocket lights, and cubby bin lights.
20_BV_OM_EN_US_t.book Page 67 GETTING TO KNOW YOUR VEHICLE 67 Front Lights The courtesy lights are mounted between the sun visors above the rear view mirror. The light switches are used to turn the lights on or off. 2 1— Left Switch 2— Right Switch Driver’s Courtesy Lights Courtesy Light Switches To operate the courtesy lights, push either the driver or passenger light switch.
20_BV_OM_EN_US_t.book Page 68 68 GETTING TO KNOW YOUR VEHICLE NOTE: • Before exiting the vehicle, make sure that the interior lights are turned off. This will prevent the battery from discharging once the doors are closed. • If a light is left on, it will automatically be turned off after approximately 15 minutes after the ignition is in the OFF position. Rear Lights Push the button on the rear dome light once to turn the light on, and the lights will remain on at all times.
20_BV_OM_EN_US_t.book Page 69 GETTING TO KNOW YOUR VEHICLE 69 Vehicles With Retractable Roof For vehicles equipped with a retractable roof, there are two interior lights located above the grab handles of the rear doors. 2 Interior Light Locations The lights come on by opening any of the doors.
20_BV_OM_EN_US_t.book Page 70 70 GETTING TO KNOW YOUR VEHICLE Dome Light Timing The Dome Light will automatically illuminate when the doors are unlocked, the doors are opened or after the doors are closed. Timing Entering The Vehicle The dome lights illuminate in the following ways: • When the doors are unlocked, the dome light will illuminate for approximately 27 seconds. • When one of the doors is opened, the dome light will illuminate for approximately three minutes.
20_BV_OM_EN_US_t.book Page 71 GETTING TO KNOW YOUR VEHICLE 71 Cargo Area Lights One interior light is located in the cargo area on the driver’s side trim panel. 2 This light automatically turns on/off when the liftgate is opened and closed, regardless of the position of the ignition. WIPERS AND WASHERS The windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever.
20_BV_OM_EN_US_t.book Page 72 72 GETTING TO KNOW YOUR VEHICLE Front Wiper Operation Mist Rotate the windshield wiper knob to one of the two detent positions for intermittent settings, the third detent for low wiper operation and the fourth for high wiper operation. Use this feature when weather conditions make occasional usage of the wipers necessary. Push the lever upward to the MIST position and release for a single wiping cycle.
20_BV_OM_EN_US_t.book Page 73 GETTING TO KNOW YOUR VEHICLE This function can be activated or deactivated by the Uconnect Settings through the radio. Refer to “Uconnect Settings” in “Multimedia” for further information. 73 Rain Sensing Wipers – Inhibition When the user changes the ignition position from OFF to RUN or START with the lever already in the intermittent position, no wipe cycle is performed for safety reasons. This temporary inhibition avoids accidental activations of the 2 wiping (e.
20_BV_OM_EN_US_t.book Page 74 74 GETTING TO KNOW YOUR VEHICLE NOTE: • The Rain Sensing feature will not operate when the wiper switch is in the low or high-speed position. • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the windshield. • Use of Rain-X or products containing wax or silicone may reduce Rain Sensing performance.
20_BV_OM_EN_US_t.book Page 75 GETTING TO KNOW YOUR VEHICLE Rear Window Defroster The rear window defroster button is located with the Climate Controls on the instrument panel. Push this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes. To manually shut the defroster off, push the button a second time.
20_BV_OM_EN_US_t.book Page 76 76 GETTING TO KNOW YOUR VEHICLE Windshield Wiper De-Icer — If Equipped Your vehicle may be equipped with a Windshield Wiper De-Icer feature that may be activated under the following conditions: • Activation By Front Defrost — The Windshield Wiper De-Icer will be activated automatically in the case of a cold weather manual start with full front defrost, and the ambient temperature is below 40°F (4.4°C).
20_BV_OM_EN_US_t.book Page 77 GETTING TO KNOW YOUR VEHICLE Auto-On Rear Window Defroster/Windshield Wiper De-Icer — If Equipped When turning the vehicle ON, the Rear Window Defroster and Windshield Wiper De-Icer will automatically turn on when the outside ambient temperature is less than 40°F (4.4°C). The Rear Window Defroster and Windshield Wiper De-Icer automatically turn off after approximately 20 minutes. To manually shut the defroster/windshield off, push the button a second time.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 80 80 GETTING TO KNOW YOUR VEHICLE Manual Climate Control Descriptions Icon Description MAX A/C Control MAX A/C sets the system for maximum cooling performance. Rotate the Temperature Control Knob counterclockwise until it is set to MAX A/C. In MAX A/C, the blower speed and mode position can be adjusted to desired user settings. A/C Button Push the A/C button to engage the Air Conditioning. The A/C LED light illuminates when the A/C is on.
20_BV_OM_EN_US_t.book Page 81 GETTING TO KNOW YOUR VEHICLE Icon 81 Description Temperature Control Use the Temperature Control Knob to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from the top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperature.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 83 GETTING TO KNOW YOUR VEHICLE 83 2 Uconnect 4C/4C NAV with 8.
20_BV_OM_EN_US_t.book Page 84 84 GETTING TO KNOW YOUR VEHICLE Automatic Climate Control Descriptions Icon Description MAX A/C Button MAX A/C sets the system for maximum cooling performance. Push the button to turn on the MAX A/C setting. In MAX A/C, the blower speed and mode position can be adjusted to desired user settings. NOTE: The MAX A/C button is only on the touchscreen. A/C Button Push the A/C Control Button to change the current setting. The indicator illuminates when the A/C is ON.
20_BV_OM_EN_US_t.book Page 85 GETTING TO KNOW YOUR VEHICLE Icon 85 Description Front Defrost Button The Front Defrost button changes the current airflow setting to Defrost mode. The indicator illuminates when this feature is on. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase. Use Defrost mode with maximum temperature settings for best windshield and side window defrosting and defogging.
20_BV_OM_EN_US_t.book Page 86 86 GETTING TO KNOW YOUR VEHICLE Icon Description Driver and Passenger Temperature Control Push these buttons to regulate the temperature of the driver and passenger settings independently. Pushing the blue arrow indicates cooler temperatures, while pushing the red button indicates warmer temperatures. SYNC Button Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indicator is illuminated when this feature is enabled.
20_BV_OM_EN_US_t.book Page 87 GETTING TO KNOW YOUR VEHICLE Icon Faceplate Knob 87 Description Mode Control Faceplate: Push the Mode Button to change the airflow distribution mode. The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets. Touchscreen Mode Touchscreen: Press one of the “MODE” buttons to change the airflow distribution mode.
20_BV_OM_EN_US_t.book Page 88 88 GETTING TO KNOW YOUR VEHICLE Icon Floor Mode Mix Mode Description Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
20_BV_OM_EN_US_t.book Page 89 GETTING TO KNOW YOUR VEHICLE 89 Automatic Temperature Control (ATC) Operating Tips Automatic Operation NOTE: Refer to the chart at the end of this section for suggested control settings for various weather conditions. 1. Push the AUTO button on the front ATC panel. The system regulates the amount of airflow. 2. Adjust the temperature you would like the system to maintain, by adjusting the driver, and passenger temperatures.
20_BV_OM_EN_US_t.book Page 90 90 GETTING TO KNOW YOUR VEHICLE blower setting on high. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again. Window Fogging Vehicle windows tend to fog on the inside in mild, rainy, and/or humid weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.
20_BV_OM_EN_US_t.book Page 91 GETTING TO KNOW YOUR VEHICLE Air Recirculation Push and release the Air Recirculation button so that the LED is on, to enter recirculation mode. It is recommended to turn the internal air recirculation on while standing in traffic or in tunnels to prevent the introduction of polluted air. Do not use the function for a long period of time, particularly if there are many passengers in the vehicle, to prevent the windows from misting up.
20_BV_OM_EN_US_t.book Page 92 92 GETTING TO KNOW YOUR VEHICLE WINDOWS Power Window Controls The power window switch is located on the driver’s door panel. The driver’s power window switch controls the operation of all the windows. There are single window controls on each passenger door trim panel, which operate the passenger door windows. The window controls will operate only when the ignition is in the ON or RUN position.
20_BV_OM_EN_US_t.book Page 93 GETTING TO KNOW YOUR VEHICLE WARNING! Never leave children unattended in a vehicle, and do not let children play with power windows. Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ACC or ON/ RUN mode. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.
20_BV_OM_EN_US_t.book Page 94 94 GETTING TO KNOW YOUR VEHICLE WARNING! There is no auto-reverse protection when the window is almost closed. To avoid personal injury be sure to clear your arms, hands, fingers and all objects from the window path before closing. Reset Auto-Up Should the Auto-Up feature stop working, the window probably needs to be reset. To reset Auto-Up: 1.
20_BV_OM_EN_US_t.book Page 95 GETTING TO KNOW YOUR VEHICLE 95 POWER MY SKY SUNROOF — IF EQUIPPED Power My Sky Operation Open/Close The Front Panel 2 The power My Sky switches are located on the overhead console. The switches are used to open and close the front panel. Operation Switch 1 — Front Panel Open/Close Switch 2 — Front Panel Vent Switch To automatically retract the front panel to the open position, push the open/close button and release.
20_BV_OM_EN_US_t.book Page 96 96 GETTING TO KNOW YOUR VEHICLE Venting The Front Panel To vent the front panel push and release the vent switch. During the vent operation any push on the open/close switch will stop the closing of the panel. NOTE: • If the My Sky is in open position, the vent switch must be held until the panel vents. • The power roof controls will operate only when the ignition is in the ON or RUN position.
20_BV_OM_EN_US_t.book Page 97 GETTING TO KNOW YOUR VEHICLE 97 8. Release the front panel close switch, then push and hold it again within 5 seconds. Do not release the switch. 9. As the front panel close switch is held, the sunroof panel will cycle to the fully open position and then back to the fully closed position again. 2 10. Once all sunroof motion has stopped, release the front panel close switch. Sunroof reinitialization and obstacle calibration is now complete.
20_BV_OM_EN_US_t.book Page 98 98 GETTING TO KNOW YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized. If the buffeting occurs with the rear windows open, then open the front and rear windows together to minimize the buffeting.
20_BV_OM_EN_US_t.book Page 99 GETTING TO KNOW YOUR VEHICLE WARNING! • Never leave children unattended in a vehicle, or with access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children. Do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go in the ON/RUN mode. Occupants, particularly unattended children, can become entrapped by the power sunroof while operating the power sunroof switch.
20_BV_OM_EN_US_t.book Page 100 100 GETTING TO KNOW YOUR VEHICLE Closing Power Sun Shade Closing Sunroof Opening Power Shade — Automatic Mode To close the sunroof completely, pull the Open/Close switch and the sunroof will fully close. The sunroof can be stopped in any position by pushing/pulling the switch a second time while it is closing. Push the shade switch for about one-half second and the shade will automatically open.
20_BV_OM_EN_US_t.book Page 101 GETTING TO KNOW YOUR VEHICLE Closing Power Shade — Manual Mode To close the shade part way (manually), pull the shade switch briefly and release. NOTE: • The sunroof and the shade controls will operate only when the ignition is in the ON or RUN position. • If the Remote Start functionality is active, it is not possible to move the sunroof. Auto Reverse Feature This feature will detect an obstruction in the opening of the sunroof during the Automatic Close operation.
20_BV_OM_EN_US_t.book Page 102 102 GETTING TO KNOW YOUR VEHICLE HOOD To Open The Hood Two latches must be released to open the hood. 1. Pull the hood release lever located under the driver’s side of the instrument panel. 2. Move to the outside of the vehicle and push the safety latch release lever toward the passenger side of the vehicle. The hood release lever is located behind the center front edge of the hood.
20_BV_OM_EN_US_t.book Page 103 GETTING TO KNOW YOUR VEHICLE 103 Remove the support rod from the locking tab and insert it into the seat located on the underside of the hood. Be sure the rod is locked into position.
20_BV_OM_EN_US_t.book Page 104 104 GETTING TO KNOW YOUR VEHICLE To Close The Hood Hold up the hood with one hand, and with the other hand, remove the support rod from its seat and reinsert it into the locking tab. Lower the hood to approximately 12 inches (30 cm) from the engine compartment and drop. Make sure that the hood is completely closed. WARNING! Support Rod And Seat 1 — Support Rod 2 — Support Rod Seat Be sure the hood is fully latched before driving your vehicle.
20_BV_OM_EN_US_t.book Page 105 GETTING TO KNOW YOUR VEHICLE 105 LIFTGATE Opening To unlock the liftgate, use the key fob or activate the power door lock switches located on the driver door handle. 2 To open the liftgate, squeeze the electronic liftgate release and pull the liftgate open with one fluid motion. Liftgate Handle Location 1 — Electronic Liftgate Release 2 — Liftgate Passive Entry Location The Liftgate Passive Entry unlock feature is built into the electronic liftgate release.
20_BV_OM_EN_US_t.book Page 106 106 GETTING TO KNOW YOUR VEHICLE Emergency Opening Proceed as follows: 4. Insert the screwdriver into the release tab slot to trigger the release tab of the liftgate. 1. Remove the rear shelf (if equipped). 2. Fold the rear seats forward. 3. Using the supplied screwdriver (located under cargo floor in tool kit), remove the yellow tab.
20_BV_OM_EN_US_t.book Page 107 GETTING TO KNOW YOUR VEHICLE 107 Closing To Lock The Liftgate Grasp the liftgate pull handle and initiate lowering the liftgate. Release the handle when the liftgate reaches self closing position. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, pushing the Keyless Enter-N-Go — Passive Entry lock button located to the right of the outside handle release 2 will lock the vehicle.
20_BV_OM_EN_US_t.book Page 108 108 GETTING TO KNOW YOUR VEHICLE Cargo Area Features Removable Rear Shelf — If Equipped To remove rear shelf, proceed as follows: 1. Disconnect the two links that support the shelf at the eyelets. 3. Clear the pins placed outside of the shelf, and then remove the rear shelf pulling it upwards. 4. The rear shelf can be stored in the cargo area, or behind the front seatbacks. Adjusting The Rear Shelf 1 — Eyelets 2 — Links Rear Shelf Support Links 2.
20_BV_OM_EN_US_t.book Page 109 GETTING TO KNOW YOUR VEHICLE 109 Position 1 (Lowered Position): This position allows you to make the load floor flat for ease of loading/unloading objects from the cargo area. This position also makes it possible to use the space below as another 2 compartment for storing fragile or smaller objects. Position 2 (Elevated Position): When the rear seatbacks and front passenger seat is folded flat, it will allow for loading objects of long dimensions.
20_BV_OM_EN_US_t.book Page 110 110 GETTING TO KNOW YOUR VEHICLE Table Tilt Load In addition to the two positions described above, the load floor can also be placed in a tilted position, slanted toward the rear seatbacks as to ease the access to the underlying zone of the luggage compartment (e.g. to pick up the spare tire or the Tire Service Kit). Place the load floor in a way that it rests at the supports 1 and 2 on the sides of the cargo area.
20_BV_OM_EN_US_t.book Page 111 GETTING TO KNOW YOUR VEHICLE 111 Access To The Loading Floor To access the double load compartment, proceed as follows: 1. Lift up on the Load Floor Handle. Table Tilt Load Supports 1 — Loading Floor Support One 2 — Loading Floor Support Two Load Floor Handle 1 — Cargo Load Floor 2 — Cargo Load Floor Handle 2. Place the desired objects inside the compartment. 3. Reposition the load floor.
20_BV_OM_EN_US_t.book Page 112 112 GETTING TO KNOW YOUR VEHICLE Displacement Load Floor To position the load floor from the lower to the upper position, proceed as follows: 1. Grasp the load floor handle and lift up the load floor. 2. Correctly place the load floor on the side panel guides and on the rear cross member.
20_BV_OM_EN_US_t.book Page 113 GETTING TO KNOW YOUR VEHICLE Anchoring Of The Load The cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. 113 The side panels may be equipped with three grocery hooks (one on the left side and two on the right side) for securing loads that are not excessively heavy.
20_BV_OM_EN_US_t.book Page 114 114 GETTING TO KNOW YOUR VEHICLE Cargo Box — If Equipped The cargo area contains a preformed cargo box that can be used for the storage of objects that allows you to obtain a uniform level when loading. Grocery Hooks Cargo Box NOTE: The cargo box is sized for a maximum capacity of distributed weight equal to 242 lbs (110 kg).
20_BV_OM_EN_US_t.book Page 115 GETTING TO KNOW YOUR VEHICLE 115 INTERNAL EQUIPMENT Glove Compartment The glove compartment is located on the passenger’s side of the instrument panel. 2 To open the glove compartment proceed as follows: 1. Unlock the compartment using the vehicle emergency key. 2. Pull the handle to open the compartment. Opening The Glove Compartment 1 — Glove Compartment Handle Once the glove compartment is open, a light will turn on to illuminate the compartment.
20_BV_OM_EN_US_t.book Page 116 116 GETTING TO KNOW YOUR VEHICLE Sun Visors Sun visors are located on both sides of the rearview mirror. The visors can be lowered or moved to the side to help block sunlight from entering the windshield or door glass. To move the sun visor against the driver or passenger door glass, remove the sun visor from the hook and turn it toward the side window.
20_BV_OM_EN_US_t.book Page 117 GETTING TO KNOW YOUR VEHICLE Extendible Sun Visor To extend the sun visor, proceed as follows: 3. Slide out the sun visor extender for even more side coverage toward the rear. 1. Place the sun visor against the door glass by detaching it from the hook and turning it toward the side window. 2 2. Slide the visor along the rod to provide coverage more to the rear.
20_BV_OM_EN_US_t.book Page 118 118 GETTING TO KNOW YOUR VEHICLE Power Outlets WARNING! The front power outlet is located under the center stack of the instrument panel. It only operates with the ignition in the RUN position. The power outlet can power mobile phones, electronics and other low power devices. To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands.
20_BV_OM_EN_US_t.book Page 119 GETTING TO KNOW YOUR VEHICLE 119 CAUTION! • Many accessories that can be plugged in draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle's battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. 2 • Accessories that draw higher power (i.e., coolers, vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
20_BV_OM_EN_US_t.book Page 120 120 GETTING TO KNOW YOUR VEHICLE devices requiring up to 150 Watts. Certain high-end video game consoles will exceed this power limit, as will most power tools. The Power Inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the Power Inverter will automatically shut down. Once the electrical device has been removed from the Power Inverter it will automatically reset.
20_BV_OM_EN_US_t.book Page 121 GETTING TO KNOW YOUR VEHICLE Cigar Lighter — If Equipped 121 WARNING! NOTE: Cigar lighters can be purchased at an authorized dealer through Mopar parts. When the cigar lighter is in use it becomes very hot. To avoid serious injury, handle the cigar lighter with care. Always check that the cigar lighter has turned off. The cigar lighter is located under the center stack of the Instrument Panel. Push lighter inward to heat.
20_BV_OM_EN_US_t.book Page 122 122 GETTING TO KNOW YOUR VEHICLE Ashtray — If Equipped Front Armrest NOTE: Ashtrays can be purchased at an authorized dealer through Mopar parts. The front armrest is located between the front seats. The ashtray is a plastic container that can be placed into one of the cup holders. The armrest can be adjusted by moving it forward or rearward.
20_BV_OM_EN_US_t.book Page 123 GETTING TO KNOW YOUR VEHICLE 123 Cupholders There are two cupholders for the front seat passengers, located in the center console. 2 Storage Compartment Push the storage handle and lift up the armrest to access the storage compartment. WARNING! Do not operate this vehicle with a console compartment lid in the open position. Driving with the console compartment lid open may result in injury in a collision.
20_BV_OM_EN_US_t.book Page 124 124 GETTING TO KNOW YOUR VEHICLE There are two cupholders located in the rear armrest if equipped. Handle Grip The handle grip is located on the passenger side of the instrument panel. The handle can be used to enter or exit the vehicle or when traveling on rough terrain.
20_BV_OM_EN_US_t.book Page 125 GETTING TO KNOW YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED Your vehicle may be equipped with a Roof Luggage Rack for transporting accessories. Crossbars should always be used whenever cargo is placed on the Roof Luggage Rack. Check the straps frequently to be sure that the load remains securely attached. NOTE: Crossbars can be purchased at an authorized dealer through Mopar parts. External racks do not increase the total load carrying capacity of the vehicle.
20_BV_OM_EN_US_t.book Page 126 126 GETTING TO KNOW YOUR VEHICLE CAUTION! • To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. • Long loads, which extend over the windshield, should be secured to both the front and rear of the vehicle. • Place a blanket or other protection between the surface of the roof and the load.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 128 128 GETTING TO KNOW YOUR INSTRUMENT PANEL Premium Instrument Cluster Instrument Cluster Descriptions 1. Tachometer • Indicates the engine speed in revolutions per minute (RPM x 1000). 2. Temperature Gauge • The temperature gauge shows engine coolant temperature. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
20_BV_OM_EN_US_t.book Page 129 GETTING TO KNOW YOUR INSTRUMENT PANEL • The gauge will likely indicate a higher temperature when driving in hot weather or up mountain grades. It should not be allowed to exceed the upper limits of the normal operating range. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats.
20_BV_OM_EN_US_t.book Page 130 130 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Instrument Cluster Display Location And Controls Your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the OFF position, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers, in the odometer.
20_BV_OM_EN_US_t.book Page 131 GETTING TO KNOW YOUR INSTRUMENT PANEL • Trip • Stop/Start — If Equipped • Audio • Messages • Screen Setup • Settings Setting the system allows the driver to select information by pushing the following buttons mounted on the steering wheel: 131 • UP Arrow Button Push and release the up arrow button to scroll upward through the main menu and submenus. •DOWN Arrow Button Push and release the down arrow button to scroll downward through the main menu and 3 submenus.
20_BV_OM_EN_US_t.book Page 132 132 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Change Reset Oil Change Due Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Due” message will display in the instrument cluster display for five seconds after a single chime has sounded to indicate the next scheduled oil change interval.
20_BV_OM_EN_US_t.book Page 133 GETTING TO KNOW YOUR INSTRUMENT PANEL 133 Vehicle Info Driver Assist — If Equipped Push and release the up or down arrow button until “Vehicle Info” is highlighted in the instrument cluster display. Push and release the right arrow button and Coolant Temp will be displayed.
20_BV_OM_EN_US_t.book Page 134 134 GETTING TO KNOW YOUR INSTRUMENT PANEL Trip Info Push and release the up or down arrow button until the Trip menu title is displayed in the instrument cluster display. Toggle the left or right arrow button to select Trip A or Trip B. The Trip information will display the following: • Distance – Shows the total distance (mi or km) traveled for Trip A or Trip B since the last reset.
20_BV_OM_EN_US_t.book Page 135 GETTING TO KNOW YOUR INSTRUMENT PANEL 135 Screen Setup In The Upper-Left/Top Right This menu item allows you to change the position of the information on the display.
20_BV_OM_EN_US_t.book Page 136 136 GETTING TO KNOW YOUR INSTRUMENT PANEL Restore Default Settings Selecting this item, and you can reset and restore the default settings. Settings This menu item allows you to change the settings for the following: • Display • Units • Clock and Date Vehicles Equipped With Multi-functional Display Reconfigurable: The following menu/submenu items are available in the cluster display.
20_BV_OM_EN_US_t.book Page 137 GETTING TO KNOW YOUR INSTRUMENT PANEL “Units Of Measure” By selecting the item “Units of Measure,” you can select the unit of measure to use for displaying various magnitudes. Possible options are: • US • Metric • Custom “Clock & Date” By selecting the item, “Clock & Date” you can adjust the clock.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 139 GETTING TO KNOW YOUR INSTRUMENT PANEL TRIP COMPUTER The Trip computer is used to display information on car operation when the key is turned to the RUN position. This function allows you to define two separate trips called “Trip A” and “Trip B” where the car's “complete trips” are monitored in an independent manner. Both trips can be reset (reset - start of a new trip). To perform a reset, push and hold the OK button on the steering wheel controls.
20_BV_OM_EN_US_t.book Page 140 140 GETTING TO KNOW YOUR INSTRUMENT PANEL WARNING/INDICATOR LIGHTS AND MESSAGES Red Warning Lights The warning/indicator light switches on in the instrument panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner Manual, which you are advised to read carefully in all cases.
20_BV_OM_EN_US_t.book Page 141 GETTING TO KNOW YOUR INSTRUMENT PANEL If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected.
20_BV_OM_EN_US_t.book Page 142 142 GETTING TO KNOW YOUR INSTRUMENT PANEL Battery Charge Warning Light Electronic Throttle Control (ETC) Warning Light This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible. This light informs you of a problem with the Electronic Throttle Control (ETC) system.
20_BV_OM_EN_US_t.book Page 143 GETTING TO KNOW YOUR INSTRUMENT PANEL Engine Temperature Warning Light This warning light will illuminate to warn of an overheated engine condition. If the engine coolant temperature is too high, this light will illuminate and a single chime will sound. 143 Liftgate Open Warning Light This indicator will illuminate when the liftgate is left open and not fully closed. Oil Pressure Warning Light If the light turns on while driving, safely pull over and stop the vehicle.
20_BV_OM_EN_US_t.book Page 144 144 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Temperature Warning Light This warning light will illuminate to indicate the engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Wait for oil temperature to return to normal levels. Seat Belt Reminder Warning Light This warning light indicates when the driver or passenger seat belt is unbuckled.
20_BV_OM_EN_US_t.book Page 145 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Warning Lights Active Speed Limiter Fault Indicator Light — If Equipped This warning light will illuminate to signal when there is a fault detected with the Active Speed Limiter. Adaptive Cruise Control (ACC) Fault Warning Light — If Equipped This warning light will illuminate to indicate a fault in the ACC system. Contact a local authorized dealer for service.
20_BV_OM_EN_US_t.book Page 146 146 GETTING TO KNOW YOUR INSTRUMENT PANEL Audio System Failure Light — If Equipped This light will illuminate to report a failure of the Audio System. Contact an authorized dealership as soon as possible. Electronic Park Brake Warning Light This warning light will illuminate to indicate the Electronic Park Brake is not functioning properly and service is required. Contact an authorized dealer.
20_BV_OM_EN_US_t.book Page 147 GETTING TO KNOW YOUR INSTRUMENT PANEL Service LaneSense Warning Light — If Equipped This warning light will illuminate when the LaneSense system is not operating and requires service. Please see an authorized dealer. Engine Check/Malfunction Indicator Warning Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems.
20_BV_OM_EN_US_t.book Page 148 148 GETTING TO KNOW YOUR INSTRUMENT PANEL Service Forward Collision Warning (FCW) Light — If Equipped This warning light will illuminate to indicate a fault in the Forward Collision Warning System. Contact an authorized dealer for service. Refer to “Forward Collision Warning (FCW)” in “Safety” for further information.
20_BV_OM_EN_US_t.book Page 149 GETTING TO KNOW YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
20_BV_OM_EN_US_t.book Page 150 150 GETTING TO KNOW YOUR INSTRUMENT PANEL transmission into PARK and run the engine at idle or slightly higher until the light turns off. Yellow Indicator Lights 4WD Low Indicator Light — If Equipped WARNING! This light alerts the driver that the vehicle is in the four-wheel drive LOW mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed.
20_BV_OM_EN_US_t.book Page 151 GETTING TO KNOW YOUR INSTRUMENT PANEL 151 Electronic Stability Control (ESC) Active Warning Light — If Equipped Electronic Stability Control (ESC) OFF Warning Light — If Equipped This warning light will indicate when the Electronic Stability Control system is Active. The “ESC Indicator Light” in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/ RUN position, and when ESC is activated. It should go out with the engine running.
20_BV_OM_EN_US_t.book Page 152 152 GETTING TO KNOW YOUR INSTRUMENT PANEL Immobilizer Fail / VPS Electrical Alarm Indicator Light This telltale will illuminate when the vehicle security alarm system has detected an attempt to break into the vehicle. White Indicator Lights Hill Descent Control (HDC) Indicator Light — If Equipped NOTE: After cycling the ignition to the ON/RUN position, the Vehicle Security Warning Light could illuminate if a problem with the system is detected.
20_BV_OM_EN_US_t.book Page 153 GETTING TO KNOW YOUR INSTRUMENT PANEL Blue Indicator Lights High Beam Indicator Light This indicator light will illuminate to indicate that the high beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams.
20_BV_OM_EN_US_t.book Page 154 154 GETTING TO KNOW YOUR INSTRUMENT PANEL Turn Signal Indicator Lights ONBOARD DIAGNOSTIC SYSTEM (OBD II) When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right). Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II.
20_BV_OM_EN_US_t.book Page 155 GETTING TO KNOW YOUR INSTRUMENT PANEL Onboard Diagnostic System (OBD II) Cybersecurity Your vehicle is required to have an Onboard Diagnostic system (OBD II) and a connection port to allow access to information related to the performance of your emissions controls. Authorized service technicians may need to access this information to assist with the diagnosis and service of your vehicle and emissions system.
20_BV_OM_EN_US_t.book Page 156 156 GETTING TO KNOW YOUR INSTRUMENT PANEL Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station. To check if your vehicle's OBD II system is ready, you must do the following: 1. Cycle the ignition switch to the ON position, but do not crank or start the engine. NOTE: If you crank or start the engine, you will have to start this test over. 2.
20_BV_OM_EN_US_t.book Page 157 157 SAFETY SAFETY FEATURES Anti-Lock Brake System (ABS) You also may experience the following when ABS activates: • The ABS motor noise (it may continue to run for a short time after the stop) The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most braking conditions. The system automatically prevents wheel lock, and enhances vehicle control during braking.
20_BV_OM_EN_US_t.book Page 158 158 SAFETY WARNING! (Continued) If the “Anti-Lock Brake Warning Light” remains on or comes on while driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required. However, the conventional brake system will continue to operate normally if the “Anti-Lock Brake Warning Light” is on.
20_BV_OM_EN_US_t.book Page 159 SAFETY 159 Brake Assist System (BAS) Dynamic Steering Torque (DST) The Brake Assist System (BAS) is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sensing the rate and amount of brake application and then applies optimum pressure to the brakes. This can help reduce braking distances. The BAS complements the Anti-Lock Brake System (ABS).
20_BV_OM_EN_US_t.book Page 160 160 SAFETY wheel lift occurring during severe or evasive driving maneuvers, and it will only intervene during these types of maneuvers. It cannot prevent wheel lift due to other factors, such as road conditions, leaving the roadway, or striking objects or other vehicles. NOTE: ERM is disabled anytime the ESC is in “Full Off” mode. Refer to Electronic Stability Control (ESC) in Safety for a complete explanation of the available ESC modes.
20_BV_OM_EN_US_t.book Page 161 SAFETY The “ESC Activation/Malfunction Indicator Light” located in the instrument cluster will start to flash as soon as the ESC system becomes active. The “ESC Activation/Malfunction Indicator Light” also flashes when the TCS is active. If the “ESC Activation/Malfunction Indicator Light” begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions.
20_BV_OM_EN_US_t.book Page 162 162 SAFETY ESC On – Two Wheel Drive Vehicles And Four Wheel Drive Vehicles In 2WD And 4H Range This is the normal operating mode for ESC when operating a two-wheel drive vehicle. It is also the normal mode for operating a four-wheel drive vehicle in 2WD or 4H Range. The ESC system will be in “ESC On” mode whenever the vehicle is started or the power transfer unit (if equipped) is shifted out of 4L Range. This mode should be used for most driving situations.
20_BV_OM_EN_US_t.book Page 163 SAFETY ation requiring “Partial Off” mode is overcome, turn ESC back on by momentarily pushing the “ESC OFF” button. This may be done while the vehicle is in motion. WARNING! • When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature described in the TCS section), has been disabled and the “ESC Off Indicator Light” will be illuminated.
20_BV_OM_EN_US_t.book Page 164 164 SAFETY PARK position. This will occur even if the message was cleared previously. Selec-Terrain — If Equipped On models equipped with Selec-Terrain, the activation of some driving modes provide partial off or full off of some active safety systems in order to optimize performance in specific modes. Partial or full off of the active safety systems will be indicated by a light in the instrument cluster.
20_BV_OM_EN_US_t.book Page 165 SAFETY NOTE: 165 Hill Descent Control (HDC) — If Equipped • The “ESC Activation/Malfunction Indicator Light” and the “ESC OFF Indicator Light” come on momentarily each time the ignition switch is turned on. • Each time the ignition is turned on, the ESC system will be on even if it was turned off previously. • The ESC system will make buzzing or clicking sounds when it is active.
20_BV_OM_EN_US_t.book Page 166 166 SAFETY HDC has three states: Activating HDC 1. Off (feature is not enabled and will not activate). Once HDC is enabled, it will activate automatically if driven down a grade of sufficient magnitude (greater than approximately 8%). The set speed for HDC is selectable by the driver and can be adjusted using brake and throttle input. 2.
20_BV_OM_EN_US_t.book Page 167 SAFETY Disabling HDC HDC will be deactivated and disabled if any of the following conditions occur: • The driver pushes the HDC switch. • The driveline is shifted out of 4L Range. • The driver’s door opens. • The vehicle is driven greater than 25 mph (40 km/h) (HDC exits immediately.) Feedback To The Driver: The instrument cluster has an HDC icon and the HDC switch has an LED, which offers feedback to the driver about the state HDC is in.
20_BV_OM_EN_US_t.book Page 168 168 SAFETY • The gear selection must match vehicle uphill direction (i.e., vehicle facing uphill is in forward gear; vehicle backing uphill is in REVERSE gear). • For vehicles equipped with an automatic transmission, the HSA will work in REVERSE gear and all forward gears. The system will not activate if the transmission is in PARK.
20_BV_OM_EN_US_t.book Page 169 SAFETY Trailer Sway Control (TSC) — If Equipped AUXILIARY DRIVING SYSTEMS Trailer Sway Control (TSC) uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sway of the trailer. TSC will become active automatically once an excessively swaying trailer is recognized.
20_BV_OM_EN_US_t.book Page 170 170 SAFETY system sensors operate when the vehicle is in any forward gear or REVERSE (R) and enters stand-by mode when the vehicle is in PARK (P). The BSM detection zone covers approximately one lane width on both sides of the vehicle, 10 ft (3 m). The zone length starts at the outside mirror and extends approximately 20 ft (6 m) beyond the rear bumper of the vehicle.
20_BV_OM_EN_US_t.book Page 171 SAFETY The BSM system notifies the driver of objects in the detection zones by illuminating the BSM warning light located in the outside mirrors in addition to sounding an audible (chime) alert and reducing the radio volume. Refer to “Modes Of Operation” in this section for further information. 171 Entering From The Side Vehicles that move into your adjacent lanes from either side of the vehicle.
20_BV_OM_EN_US_t.book Page 172 172 SAFETY Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either side and enter the rear detection zone with a relative speed of less than 31 mph (50 km/h). If you pass another vehicle slowly with a relative speed of less than 15 mph (25 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated.
20_BV_OM_EN_US_t.book Page 173 SAFETY 173 4 Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes.
20_BV_OM_EN_US_t.book Page 174 174 SAFETY Rear Cross Path (RCP) The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed. The RCP system will then have a clear view of the cross traffic and if an oncoming vehicle is detected, alert the driver.
20_BV_OM_EN_US_t.book Page 175 SAFETY RCP monitors the rear detection zones on both sides of the vehicle, for objects that are moving toward the side of the vehicle with a minimum speed of approximately 1 mph (2 km/h), to objects moving a maximum of approximately 22 mph (35 km/h), such as in parking lot situations. NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side.
20_BV_OM_EN_US_t.book Page 176 176 SAFETY NOTE: Whenever an audible alert is requested by the BSM system, the radio is also muted. When the system is in RCP, the system will respond with both visual and audible alerts when a detected object is present. Whenever an audible alert is requested, the radio is also muted. Turn/hazard signal status is ignored; the RCP state always requests the chime.
20_BV_OM_EN_US_t.book Page 177 SAFETY General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: FCC ID: RX2TCUFCA025N IC: 4983A-TCUFCA02SN This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
20_BV_OM_EN_US_t.book Page 178 178 SAFETY Forward Collision Warning (FCW) With Mitigation Operation — If Equipped The Forward Collision Warning (FCW) System with Mitigation provides the driver with audible warnings, visual warnings (within the instrument cluster display), and may apply a brake jerk to warn the driver when it detects a potential frontal collision. The warnings and limited braking are intended to provide the driver with enough time to react, avoid or mitigate the potential collision.
20_BV_OM_EN_US_t.book Page 179 SAFETY 179 • The FCW system is intended for on-road use only. If the vehicle is taken off-road, the FCW system should be deactivated to prevent unnecessary warnings to the surroundings. • If the vehicle enters 4L Range, the FCW system will be automatically deactivated. • The active braking is disabled when a trailer is connected with a Mopar Trailer Towing system.
20_BV_OM_EN_US_t.book Page 180 180 SAFETY Turning FCW On Or Off Changing FCW Sensitivity The Forward Collision menu setting is located in the Uconnect settings. By changing the settings on the menu of the Uconnect system, you can change the sensitivity of the system by choosing one of the following three options: "Near", "Medium" or "Far". Refer to “Uconnect Settings” in “Multimedia” for further information.
20_BV_OM_EN_US_t.book Page 181 SAFETY The setting of the sensitivity of the system is maintained in memory when the engine is switched off. FCW Limited Warning If the instrument cluster display reads “FCW Limited Functionality” or “FCW Limited Functionality Wipe Front Windshield” momentarily, there may be a condition that limits FCW functionality. Although the vehicle is still drivable under normal conditions, the active braking may not be fully available.
20_BV_OM_EN_US_t.book Page 182 182 SAFETY NOTE: • If the “FCW Front Radar Sensor Temporarily Blocked” message occurs frequently (e.g. more than once on every trip) without any snow, rain, mud, or other obstruction, have the radar sensor realigned at an authorized dealer. • Installing a snow plow or front-end protector is not recommended. Doing so may block the sensor and inhibit FCW operation. • Use only a soft cloth for cleaning. Do not use solvents or abrasive pastes.
20_BV_OM_EN_US_t.book Page 183 SAFETY 183 Small Vehicles And/Or Not Aligned To The Lane Lane Changing Of Other Vehicles The system is not able to detect the presence of vehicles that are in front of the vehicle but placed outside the field of action of the radar sensor and could therefore not react in the presence of small vehicles such as bicycles or motorcycles.
20_BV_OM_EN_US_t.book Page 184 184 SAFETY Passing Of Vehicles In An Oncoming Intersection General Information The system could temporarily react to a vehicle that crossed the range of the radar sensor, in an oncoming intersection.
20_BV_OM_EN_US_t.book Page 185 SAFETY Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Development applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. l'appareil ne doit pas produire de brouillage, et 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
20_BV_OM_EN_US_t.book Page 186 186 SAFETY The TPMS will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above the recommended cold placard pressure. Once the low tire pressure warning “Tire Pressure Monitoring Light” illuminates, you must increase the tire pressure to the recommended cold placard pressure in order for the “Tire Pressure Monitoring Light” to turn off.
20_BV_OM_EN_US_t.book Page 187 SAFETY CAUTION! (Continued) • After inspecting or adjusting the tire pressure always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the TPMS sensor. NOTE: • The TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or condition. • The TPMS should not be used as a tire pressure gauge while adjusting your tire pressure.
20_BV_OM_EN_US_t.book Page 188 188 SAFETY Tire Pressure Monitoring Low Pressure Warnings Service TPMS Warning The “Tire Pressure Monitoring Light” will illuminate in the instrument cluster, a “LOW TIRE PRESSURE” message will display in the instrument cluster, an "Inflate to XX" message will be displayed and a chime will sound when tire pressure is low in one or more of the four active road tires.
20_BV_OM_EN_US_t.book Page 189 SAFETY Vehicles With Compact Spare or Non-Matching Full Size Spare 1. The compact spare tire or non-matching full size spare tire does not have a tire pressure monitoring sensor. Therefore, the TPMS will not monitor the pressure in the spare tire. 2.
20_BV_OM_EN_US_t.book Page 190 190 SAFETY Tire Pressure Monitoring Low Pressure Warnings The “Tire Pressure Monitoring Light” will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or more of the four active road tires. In addition, the instrument cluster will display a "Tire Low" message for a minimum of five seconds and a graphic showing the pressure values of each tire with the low tire pressure values in a different color.
20_BV_OM_EN_US_t.book Page 191 SAFETY If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the “Tire Pressure Monitoring Light” will no longer flash, and the “SERVICE TPM SYSTEM” message will no longer display, and a pressure value will display in place of the dashes.
20_BV_OM_EN_US_t.book Page 192 192 SAFETY Vehicles With Compact Spare or Non-Matching Full Size Spare 1. The compact spare tire or non-matching full size does not have a Tire Pressure Monitoring sensor. Therefore, the TPMS will not monitor the pressure in the compact spare tire. 2.
20_BV_OM_EN_US_t.book Page 193 SAFETY TPMS Deactivation — If Equipped The TPMS can be deactivated if replacing all four wheel and tire assemblies (road tires) with wheel and tire assemblies that do not have TPMS sensors, such as when installing Winter wheel and tire assemblies on your vehicle. To deactivate the TPMS, first, replace all four wheel and tire assemblies (road tires) with tires not equipped with Tire Pressure Monitoring (TPM) sensors.
20_BV_OM_EN_US_t.book Page 194 194 SAFETY Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Development applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: OCCUPANT RESTRAINT SYSTEMS 1. l'appareil ne doit pas produire de brouillage, et Occupant Restraint Systems 2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
20_BV_OM_EN_US_t.book Page 195 SAFETY 2. A child who is not big enough to wear the vehicle seat belt properly (Refer to “Child Restraints” in this section for further information) must be secured in the appropriate child restraint or belt-positioning booster seat in a rear seating position. 3. If a child from 2 to 12 years old (not in a rear-facing child restraint) must ride in the front passenger seat, move the seat as far back as possible and use the proper child restraint.
20_BV_OM_EN_US_t.book Page 196 196 SAFETY Seat Belt Systems Initial Indication Buckle up even though you are an excellent driver, even on short trips. Someone on the road may be a poor driver and could cause a collision that includes you. This can happen far away from home or on your own street. Enhanced Seat Belt Use Reminder System (BeltAlert) If the driver is unbuckled when the ignition switch is first in the START or ON/RUN position a chime will signal for a few seconds.
20_BV_OM_EN_US_t.book Page 197 SAFETY the Seat Belt Reminder Light will remain solid red until the driver and outboard front seat passenger are buckled. The BeltAlert warning sequence may repeat based on vehicle speed until the driver and occupied outboard front seat passenger seat belts are buckled. The driver should instruct all occupants to buckle their seat belts.
20_BV_OM_EN_US_t.book Page 198 198 SAFETY NOTE: If BeltAlert has been deactivated, the Seat Belt Reminder Light will turn on and remain on until the driver and outboard front seat passenger seat belts are buckled. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/ shoulder belts. The seat belt webbing retractor will lock only during very sudden stops or collisions. This feature allows the shoulder part of the seat belt to move freely with you under normal conditions.
20_BV_OM_EN_US_t.book Page 199 SAFETY WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size. WARNING! • A lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
20_BV_OM_EN_US_t.book Page 200 200 SAFETY Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat). Grasp the latch plate and pull out the seat belt.
20_BV_OM_EN_US_t.book Page 201 SAFETY 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug seat belt reduces the risk of sliding under the seat belt in a collision. 201 6. To release the seat belt, push the red button on the buckle. The seat belt will automatically retract to its stowed position.
20_BV_OM_EN_US_t.book Page 202 202 SAFETY Adjustable Upper Shoulder Belt Anchorage In the driver and outboard front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck. Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best. anchorage button, try to move it up or down to make sure that it is locked in position.
20_BV_OM_EN_US_t.book Page 203 SAFETY Seat Belts And Pregnant Women 203 Seat Belt Pretensioner The front outboard seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision. Pretensioners work for all size occupants, including those in child restraints.
20_BV_OM_EN_US_t.book Page 204 204 SAFETY Switchable Automatic Locking Retractor (ALR) The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child Restraints” section of this manual. The figure below illustrates the locking feature for each seating position.
20_BV_OM_EN_US_t.book Page 205 SAFETY WARNING! (Continued) • Never install a rear-facing child restraint in the front seat of a vehicle. Only use a rear-facing child restraint in the rear seat. If the vehicle does not have a rear seat, do not transport a rear-facing child restraint in that vehicle. How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire seat belt is extracted. 3.
20_BV_OM_EN_US_t.book Page 206 206 SAFETY Supplemental Restraint Systems (SRS) Some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others. If you are not sure, ask an authorized dealer. The air bag system must be ready to protect you in a collision. The Occupant Restraint Controller (ORC) monitors the internal circuits and interconnecting wiring associated with the electrical Air Bag System Components.
20_BV_OM_EN_US_t.book Page 207 SAFETY The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is detected that could affect the air bag system. The diagnostics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the air bag system immediately.
20_BV_OM_EN_US_t.book Page 208 208 SAFETY Front Air Bags This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger. The front air bags are a supplement to the seat belt restraint systems. The driver front air bag is mounted in the center of the steering wheel. The passenger front air bag is mounted in the instrument panel, above the glove compartment. The words “SRS AIRBAG” or “AIRBAG” are embossed on the air bag covers.
20_BV_OM_EN_US_t.book Page 209 SAFETY The first stage inflator is triggered immediately during an impact that requires air bag deployment. A low energy output is used in less severe collisions. A higher energy output is used for more severe collisions. This vehicle may be equipped with a driver and/or front passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is buckled. The seat belt buckle switch may adjust the inflation rate of the Advanced Front Air Bags.
20_BV_OM_EN_US_t.book Page 210 210 SAFETY On the other hand, depending on the type and location of impact, front air bags may deploy in crashes with little vehicle front-end damage but that produce a severe initial deceleration. Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed.
20_BV_OM_EN_US_t.book Page 211 SAFETY 211 Supplemental Side Air Bags Supplemental Seat-Mounted Side Air Bags (SABs) This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags (SABs). Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats. The SABs are marked with “SRS AIRBAG” or “AIRBAG” on a label or on the seat trim on the outboard side of the seats.
20_BV_OM_EN_US_t.book Page 212 212 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental Side Air Bag Inflatable Curtains (SABICs) This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs). Supplemental Side Air Bag Inflatable Curtains (SABICs) are located above the side windows.
20_BV_OM_EN_US_t.book Page 213 SAFETY The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events. WARNING! • Do not mount equipment, or stack luggage or other cargo up high enough to block the deployment of the SABICs. The trim covering above the side windows where the SABIC and its deployment path are located should remain free from any obstructions.
20_BV_OM_EN_US_t.book Page 214 214 SAFETY WARNING! (Continued) • Seat belts (and child restraints where appropriate) are necessary for your protection in all collisions. They also help keep you in position, away from an inflating Side Air Bag. To get the best protection from the Side Air Bags, occupants must wear their seat belts properly and sit upright with their backs against the seats.
20_BV_OM_EN_US_t.book Page 215 SAFETY 215 Air Bag System Components If A Deployment Occurs NOTE: The Occupant Restraint Controller (ORC) monitors the internal circuits and interconnecting wiring associated with electrical Air Bag System Components listed below: The front air bags are designed to deflate immediately after deployment. • Air Bag Warning Light NOTE: Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system.
20_BV_OM_EN_US_t.book Page 216 216 SAFETY • As the air bags deflate, you may see some smoke-like particles. The particles are a normal by-product of the process that generates the non-toxic gas used for air bag inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, rinse the area with cool water. For nose or throat irritation, move to fresh air. If the irritation continues, see your doctor.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 218 218 SAFETY Enhanced Accident Response System Reset Procedure After the event occurs, when the system is active, a message regarding fuel cutoff is displayed. Turn the ignition switch from ignition AVV/START or MAR/ACC/ON/RUN to ignition STOP/OFF/LOCK. Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.
20_BV_OM_EN_US_t.book Page 219 SAFETY Customer Action 6. Place turn signal in neutral state. 7. Turn right turn signal switch ON. 8. Place turn signal in neutral state. 9. Turn left turn signal switch ON. 219 Customer Will See NOTE: Each step MUST BE held for at least two seconds Right turn light BLINKS. Left turn light is OFF. Right turn light is ON SOLID. Left turn light BLINKS. Right turn light is OFF. Left turn light BLINKS. Right turn light is ON SOLID. Left turn light is ON SOLID. 10.
20_BV_OM_EN_US_t.book Page 220 220 SAFETY Maintaining Your Air Bag System WARNING! (Continued) WARNING! • Modifications to any part of the air bag system could cause it to fail when you need it. You could be injured if the air bag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passenger side of the instrument panel.
20_BV_OM_EN_US_t.book Page 221 SAFETY Event Data Recorder (EDR) This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
20_BV_OM_EN_US_t.book Page 222 222 SAFETY Child Restraints Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the United States, and every Canadian province, requires that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Children 12 years or younger should ride properly buckled up in a rear seat, if available.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 224 224 SAFETY Infant And Child Restraints Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and convertible child seats. The infant carrier is only used rear-facing in the vehicle.
20_BV_OM_EN_US_t.book Page 225 SAFETY cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and belt-positioning booster seat are held in the vehicle by the seat belt. WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint.
20_BV_OM_EN_US_t.book Page 226 226 SAFETY child’s squirming or slouching can move the belt out of position. If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly. WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death.
20_BV_OM_EN_US_t.book Page 227 SAFETY Lower Anchors And Tethers For CHildren (LATCH) Restraint System 227 these seating positions, the seat belt must be used with the top tether anchorage to install the child restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle 4 LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
20_BV_OM_EN_US_t.book Page 228 228 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.5 kg) Use the LATCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.5 kg).
20_BV_OM_EN_US_t.book Page 229 SAFETY 229 Frequently Asked Questions About Installing Child Restraints With LATCH Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the rear removed? No head restraints be Never “share” a LATCH anchorage with two or more child restraints.
20_BV_OM_EN_US_t.book Page 230 230 SAFETY Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
20_BV_OM_EN_US_t.book Page 231 SAFETY tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not approved for installing child seats using the LATCH attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position.
20_BV_OM_EN_US_t.book Page 232 232 SAFETY 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “Installing Child Restraints Using the Top Tether Anchorage” for directions to attach a tether anchor. 5. Tighten all of the straps as you push the child restraint rearward and downward into the seat. Remove slack in the straps according to the child restraint manufacturer’s instructions. 6.
20_BV_OM_EN_US_t.book Page 233 SAFETY Installing Child Restraints Using The Vehicle Seat Belt Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. WARNING! Please see the table below and the following sections for more information. Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle • Improper installation or failure to properly secure a child restraint can lead to failure of the restraint.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 235 SAFETY 235 1. Place the child seat in the center of the seating position. For some second row seats, you may need to recline the seat and/or raise the head restraint (if adjustable) to get a better fit. If the rear seat can be moved forward and rearward in the vehicle, you may wish to move it to its rear-most position to make room for the child seat. You may also move the front seat forward to allow more room for the child seat. 6.
20_BV_OM_EN_US_t.book Page 236 236 SAFETY Installing Child Restraints Using The Top Tether Anchorage: WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat.
20_BV_OM_EN_US_t.book Page 237 SAFETY 237 Transporting Pets Air Bags deploying in the front seat could harm your pet. An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a collision. Pets should be restrained in the rear seat in pet harnesses or pet carriers that are secured by seat belts.
20_BV_OM_EN_US_t.book Page 238 238 SAFETY Exhaust Gas WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
20_BV_OM_EN_US_t.book Page 239 SAFETY 239 Air Bag Warning Light Floor Mat Safety Information The Air Bag warning light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN. If the light is either not on during starting, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible. After the bulb check, this light will illuminate with a single chime when a fault with the Air Bag System has been detected.
20_BV_OM_EN_US_t.book Page 240 240 SAFETY WARNING! (Continued) • ALWAYS REMOVE THE EXISTING FLOOR MAT FROM THE VEHICLE before installing any other floor mat. NEVER install or stack an additional floor mat on top of an existing floor mat. • ONLY install floor mats designed to fit your vehicle. NEVER install a floor mat that cannot be properly attached and secured to your vehicle. If a floor mat needs to be replaced, only use a FCA approved floor mat for the specific make, model, and year of your vehicle.
20_BV_OM_EN_US_t.book Page 241 SAFETY Periodic Safety Checks You Should Make Outside The Vehicle Tires Examine tires for excessive tread wear and uneven wear patterns. Check for stones, nails, glass, or other objects lodged in the tread or sidewall. Inspect the tread for cuts and cracks. Inspect sidewalls for cuts, cracks, and bulges. Check the wheel nuts for tightness. Check the tires (including spare) for proper cold inflation pressure.
20_BV_OM_EN_US_t.book Page 242 242 STARTING AND OPERATING STARTING THE ENGINE Proceed as follows: Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat belts. 1. Set the Electric Park Brake (EPB) and put the gear selector in the PARK or NEUTRAL position. WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle.
20_BV_OM_EN_US_t.book Page 243 STARTING AND OPERATING If Engine Fails To Start 243 WARNING! (Continued) WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle. This could result in flash fire causing serious personal injury. If the engine fails to start after you have followed the "Normal Starting" procedure, and has not experienced an extended park condition as identified in "Extended Park Starting" procedure it may be flooded.
20_BV_OM_EN_US_t.book Page 244 244 STARTING AND OPERATING Cold Weather Operation To ensure reliable starting under extreme cold conditions an externally powered electric block heater (if equipped) is required for the 1.3L Turbo engine below -20°F (-29°C) and for the 2.4L engine below -31°F (-35°C) and is recommended for the 2.4L engine below -20°F (-29°C). 2. Place the ignition in the START mode and release it when the engine starts. 3.
20_BV_OM_EN_US_t.book Page 245 STARTING AND OPERATING 245 Stopping The Engine Turbocharger “Cool Down” — If Equipped To shut off the engine with vehicle speed greater than 5 mph (8 km/h), you must push and hold the ignition or push the START/STOP button three times consecutively within a few seconds. The engine will shut down, and the ignition will be placed in the RUN position. This vehicle is equipped with an after-run pump to cool the turbocharger after the engine is shut off.
20_BV_OM_EN_US_t.book Page 246 246 STARTING AND OPERATING mended viscosity and quality grades, refer to “Dealer Service” in “Servicing And Maintenance”. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. You can engage the EPB in two ways; • Manually, by applying the park brake switch. • Automatically, by enabling the Auto Park Brake feature in the customer programmable features section of the Uconnect settings or in “Safe Hold” conditions.
20_BV_OM_EN_US_t.book Page 247 STARTING AND OPERATING foot is on the brake pedal while you apply the EPB, you may notice a small amount of brake pedal movement. The EPB can be applied even when the ignition is in the OFF mode however, it can only be released when the ignition is in the RUN mode. NOTE: The EPB fault lamp will illuminate if the EPB switch is held for longer than 60 seconds in either the released or applied position. The light will extinguish upon releasing the switch.
20_BV_OM_EN_US_t.book Page 248 248 STARTING AND OPERATING WARNING! (Continued) • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the transmission gear selector.
20_BV_OM_EN_US_t.book Page 249 STARTING AND OPERATING In the unlikely event of a malfunction of the EPB system, a yellow EPB fault lamp will illuminate. This may be accompanied by the Brake warning lamp flashing. In this status some EPB functionalities may be deactivated. In this event, urgent service of the EPB system is required. Do not rely on the EPB to hold the vehicle stationary. Auto Park Brake The EPB can be programmed to be applied automatically whenever the vehicle speed is below 1.
20_BV_OM_EN_US_t.book Page 250 250 STARTING AND OPERATING SafeHold can be temporarily bypassed by pushing the EPB Switch while the driver door is open and the brake pedal is pressed. Once manually bypassed, SafeHold will be enabled again once the vehicle reaches 12 mph (20 km/h) or the ignition is cycled to the OFF mode and back to RUN again. Brake Service Mode We recommend having your brakes serviced by your authorized dealer.
20_BV_OM_EN_US_t.book Page 251 STARTING AND OPERATING When brake service work is complete, the following steps must be followed to reset the parking brake system to normal operation: • Ensure the vehicle is at a standstill. • Press the brake pedal with moderate force. • Apply the EPB Switch. NOTE: A dedicated message will appear in the instrument cluster if Brake Service Mode cannot be deactivated. WARNING! You can be badly injured working on or around a motor vehicle.
20_BV_OM_EN_US_t.book Page 252 252 STARTING AND OPERATING To shift the gears, press the clutch pedal to the floor and put the gear selector to the desired position (the diagram for the engagement of the gears is displayed on the handle of the lever). To engage REVERSE gear from the NEUTRAL position, lift the REVERSE ring, located below the knob and simultaneously move the lever to the left and then forward. Shifting Fully press the clutch pedal before shifting gears.
20_BV_OM_EN_US_t.book Page 253 STARTING AND OPERATING NOTE: A certain amount of noise from the transmission is normal. This noise can be most noticeable when the vehicle is idling in NEUTRAL with the clutch engaged (clutch pedal released), but it may also be heard when driving. The noise may also be more noticeable when the transmission is warm. This noise is normal and is not an indication of a problem with your clutch or transmission.
20_BV_OM_EN_US_t.book Page 254 254 STARTING AND OPERATING Maximum Recommended Downshift Speeds CAUTION! Failure to follow the maximum recommended downshifting speeds may cause the engine to overspeed and/or damage the clutch disc, even if the clutch pedal is pressed.
20_BV_OM_EN_US_t.book Page 255 STARTING AND OPERATING vehicle is stopped or moving at low speeds (refer to "Brake/ Transmission Shift Interlock System" in this section). Select the DRIVE range for normal driving. The electronically-controlled transmission adapts its shift schedule based on driver inputs, along with environmental and road conditions. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt.
20_BV_OM_EN_US_t.book Page 256 256 STARTING AND OPERATING CAUTION! • Shift into or out of PARK or REVERSE only after the vehicle has come to a complete stop. • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. in the AutoStick (+/-) position (beside the DRIVE position). In AutoStick mode, the transmission gear (1, 2, 3, etc.) is displayed in the instrument cluster.
20_BV_OM_EN_US_t.book Page 257 STARTING AND OPERATING Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when shifting between these gears. DO NOT depress the accelerator pedal when shifting from PARK or NEUTRAL into another gear range. CAUTION! After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold.
20_BV_OM_EN_US_t.book Page 258 258 STARTING AND OPERATING WARNING! (Continued) • The transmission may not engage PARK if the vehicle is moving. Always bring the vehicle to a complete stop before shifting to PARK, and verify that the transmission gear position indicator solidly indicates PARK (P) without blinking. Ensure that the vehicle is completely stopped, and the PARK position is properly indicated, before exiting the vehicle.
20_BV_OM_EN_US_t.book Page 259 STARTING AND OPERATING CAUTION! 259 NEUTRAL (N) • Before moving the transmission gear selector out of PARK, you must turn the ignition to the ON/RUN mode, and also press the brake pedal. Otherwise, damage to the gear selector could result. Use this range when the vehicle is standing for prolonged periods with the engine running. The engine may be started in this range. Apply the electric park brake and shift the transmission into PARK if you must exit the vehicle.
20_BV_OM_EN_US_t.book Page 260 260 STARTING AND OPERATING DRIVE (D) This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy. The transmission automatically upshifts through all forward gears. The DRIVE position provides optimum driving characteristics under all normal operating conditions.
20_BV_OM_EN_US_t.book Page 261 STARTING AND OPERATING Operation When the gear selector is in the AutoStick position (beside the DRIVE position), it can be moved forward and rearward. This allows the driver to manually select the transmission gear being used. Moving the gear selector forward (-) triggers a downshift, and rearward (+) an upshift. The current gear is displayed in the instrument cluster.
20_BV_OM_EN_US_t.book Page 262 262 STARTING AND OPERATING Transmission Limp Home Mode 5. Restart the engine. Transmission function is electronically monitored for abnormal conditions. If a condition is detected that could result in transmission damage, Transmission Limp Home Mode is activated. In this mode, the transmission may operate only in a fixed gear, or may remain in neutral. The Malfunction Indicator Light (MIL) may be illuminated.
20_BV_OM_EN_US_t.book Page 263 STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock system (BTSI) that holds the transmission gear selector in PARK unless the brakes are applied. To shift the transmission out of PARK, the ignition must be in the RUN mode (engine running or not) and the brake pedal must be pressed.
20_BV_OM_EN_US_t.book Page 264 264 STARTING AND OPERATING Active Drive Control — If Equipped Selec-Terrain Switch The Power Transfer Unit (PTU) is locked to ensure immediate availability of torque to the rear drive axles. This feature is selectable in AUTO mode and automatic in the other driving mode. 4WD LOCK can be enabled by the following ways: • When the 4WD LOCK button is pushed. • When the Selec-Terrain switch is rotated from AUTO to any other off-road modes.
20_BV_OM_EN_US_t.book Page 265 STARTING AND OPERATING 265 Enabling 4WD LOW SELEC-TERRAIN With the vehicle stationary, the ignition in RUN mode or with the engine running, shift the transmission into NEUTRAL and push the button once 4WD LOW. The instrument cluster will display the message "4WD LOW" once the shift is complete. Selec-Terrain combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains.
20_BV_OM_EN_US_t.book Page 266 266 STARTING AND OPERATING operating conditions), the transmission will use second gear (rather than first gear) during launches, to minimize wheel slippage, except for in 4–Low (Trailhawk models only). • SAND: For off-road driving or use on surfaces with poor traction, such as sandy bottoms. The transmission is set to provide maximum traction. This mode allows more wheel spin and higher shift points to help motor through loose areas.
20_BV_OM_EN_US_t.book Page 267 STARTING AND OPERATING ACTIVE GRILLE SHUTTER — IF EQUIPPED Your vehicle may be equipped with Active Grille Shutters, an automatic system with mobile flaps applied in front of the cooling module, whose automatic opening/closing movement aims at improving the vehicle aerodynamic efficiency and thus reducing consumption while ensuring optimal engine operating temperature conditions. When a greater air flow is required for cooling (e.g.
20_BV_OM_EN_US_t.book Page 268 268 STARTING AND OPERATING STOP/START SYSTEM The Stop/Start function was developed to reduce fuel consumption. The system will stop the engine automatically during a vehicle stop if the required conditions are met. Releasing the brake pedal or pressing the accelerator pedal will automatically restart the engine. Automatic Mode The Stop/Start feature is enabled after every normal customer engine start.
20_BV_OM_EN_US_t.book Page 269 STARTING AND OPERATING Possible Reasons The Engine Does Not Autostop Prior to engine shut down, the system will check many safety and comfort conditions to see if they are fulfilled. Detailed information about the operation of the Stop/Start system may be viewed in the instrument cluster display Stop/Start Screen. In the following situations the engine will not stop: • Driver’s seat belt is not buckled. • Driver’s door is not closed.
20_BV_OM_EN_US_t.book Page 270 270 STARTING AND OPERATING To Start The Engine While In Autostop Mode While in a forward gear, the engine will start when the brake pedal is released or the throttle pedal is depressed. The transmission will automatically re-engage upon engine restart. Conditions That Will Cause The Engine To Start Automatically While In Autostop Mode: • The transmission gear selector is moved out of DRIVE except in the PARK and NEUTRAL position. • To maintain cabin temperature comfort.
20_BV_OM_EN_US_t.book Page 271 STARTING AND OPERATING To Manually Turn Off The Stop/Start System 1. Push the Stop/Start OFF switch (located on the switch bank). The light on the switch will illuminate. 271 3. At the next vehicle stop (after turning off the Stop/Start system), the engine will not be stopped. 4. The Stop/Start system will reset itself back to the ON mode every time the ignition is turned off and back on.
20_BV_OM_EN_US_t.book Page 272 272 STARTING AND OPERATING SPEED CONTROL — IF EQUIPPED When engaged, the Speed Control takes over accelerator operations at speeds greater than 20 mph (40 km/h). The Speed Control buttons are located on the right side of the steering wheel. NOTE: • In order to ensure proper operation, the Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time.
20_BV_OM_EN_US_t.book Page 273 STARTING AND OPERATING Setting A Desired Speed Turn the Speed Control on. NOTE: The vehicle should be traveling at a steady speed and on level ground before pushing the SET (+) or SET (-) button. When the vehicle has reached the desired speed, push the SET (+) or SET (-) button and release. Release the accelerator and the vehicle will operate at the selected speed.
20_BV_OM_EN_US_t.book Page 274 274 STARTING AND OPERATING To Decrease Speed Accelerating For Passing When the Speed Control is set, you can decrease speed by pushing the SET (-) button. Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. The driver’s preferred units can be selected through the instrument panel settings. Refer to “Instrument Cluster Display” in “Getting To Know Your Instrument Panel” for further information.
20_BV_OM_EN_US_t.book Page 275 STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED Adaptive Cruise Control (ACC) increases the driving convenience provided by cruise control while traveling on highways and major roadways. However, it is not a safety system and not designed to prevent collisions. Speed Control function performs differently. Please refer to the proper section within this chapter.
20_BV_OM_EN_US_t.book Page 276 276 STARTING AND OPERATING WARNING! • Adaptive Cruise Control (ACC) is a convenience system. It is not a substitute for active driving involvement. It is always the driver’s responsibility to be attentive of road, traffic, and weather conditions, vehicle speed, distance to the vehicle ahead; and, most importantly, brake operation to ensure safe operation of the vehicle under all road conditions.
20_BV_OM_EN_US_t.book Page 277 STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation The Speed Control buttons (located on the right side of the steering wheel) operate the ACC System. 277 NOTE: Any chassis/suspension or tire size modifications to the vehicle will affect the performance of the Adaptive Cruise Control and Forward Collision Warning System. To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button.
20_BV_OM_EN_US_t.book Page 278 278 STARTING AND OPERATING will turn off and the instrument cluster display will read “Adaptive Cruise Control (ACC) Off.” Activating Adaptive Cruise Control (ACC) The minimum set speed for the ACC system is 20 mph (32 km/h). When the system is turned on and in the ready state, the instrument cluster display will read “ACC Ready.” When the system is off, the instrument cluster display will read “Adaptive Cruise Control (ACC) Off.
20_BV_OM_EN_US_t.book Page 279 STARTING AND OPERATING To Set A Desired ACC Speed To Cancel When the vehicle reaches the speed desired, push the SET (+) button or the SET (-) button and release. The instrument cluster display will show the set speed. The following conditions cancel the system: NOTE: ACC cannot be set if there is a stationary vehicle in front of your vehicle in close proximity. • An Anti-Lock Brake System (ABS) event occurs. Remove your foot from the accelerator pedal.
20_BV_OM_EN_US_t.book Page 280 280 STARTING AND OPERATING To Turn Off To Vary The Speed Setting The system will turn off and clear the set speed in memory if: To Increase Speed • The Adaptive Cruise Control (ACC) on/off button is pushed. • The Normal (Fixed Speed) Cruise Control on/off button is pushed. • The ignition is placed in the OFF position. • You switch to Four-Wheel Drive Low.
20_BV_OM_EN_US_t.book Page 281 STARTING AND OPERATING 281 Metric Speed (km/h) • If the button is continually pushed, the set speed will continue to decrease in 5 mph decrements until the button is released. The decrease in set speed is reflected in the instrument cluster display. • If the button is continually pushed, the set speed will continue to increase in 5 km/h increments until the button is released. The increase in set speed is reflected in the instrument cluster display.
20_BV_OM_EN_US_t.book Page 282 282 STARTING AND OPERATING • If equipped with a manual transmission, it is possible to make gear changes during the normal operation of ACC that will allow the driver to engage the appropriate gear with respect to the set speed in order to keep the feature activated. It is canceled when the clutch pedal is held down, or when placing the gearbox in NEUTRAL for a certain maximum time.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 284 284 STARTING AND OPERATING If there is no vehicle ahead, the vehicle will maintain the set speed. If a slower moving vehicle is detected in the same lane, the instrument cluster display will show the “Sensed Vehicle Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
20_BV_OM_EN_US_t.book Page 285 STARTING AND OPERATING A Proximity Warning will alert the driver if ACC predicts that its maximum braking level is not sufficient to maintain the set distance. If this occurs, a visual alert “BRAKE!” will appear in the instrument cluster display and a chime will sound while ACC continues to apply its maximum braking capacity.
20_BV_OM_EN_US_t.book Page 286 286 STARTING AND OPERATING Adaptive Cruise Control Ready Display Warnings And Maintenance When ACC is activated but the vehicle speed setting has not been selected, the display will read “Adaptive Cruise Control Ready.
20_BV_OM_EN_US_t.book Page 287 STARTING AND OPERATING 287 If weather conditions are not a factor, the driver should examine the sensor. It may require cleaning or removal of an obstruction. The sensor is located in the center of the bumper. When the condition that deactivated the system is no longer present, the system will return to the “Adaptive Cruise Control Off” state and will resume function by simply reactivating it.
20_BV_OM_EN_US_t.book Page 288 288 STARTING AND OPERATING The “ACC/FCW Limited Functionality Wipe Front Windshield” message can sometimes be displayed while driving in adverse weather conditions. The ACC/FCW system will recover after the vehicle has left these areas. Under rare conditions, when the camera is not tracking any vehicles or objects in its path this warning may temporarily occur.
20_BV_OM_EN_US_t.book Page 289 STARTING AND OPERATING 289 Offset Driving Turns And Bends ACC may not detect a vehicle in the same lane that is offset from your direct line of travel, or a vehicle merging in from a side lane. There may not be sufficient distance to the vehicle ahead. The offset vehicle may move in and out of the line of travel, which can cause your vehicle to brake or accelerate unexpectedly.
20_BV_OM_EN_US_t.book Page 290 290 STARTING AND OPERATING Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in your lane. Depending on the speed, vehicle load, traffic conditions, and the steepness of the hills, ACC performance may be limited. ACC may not detect a vehicle until it is completely in the lane in which you are traveling.
20_BV_OM_EN_US_t.book Page 291 STARTING AND OPERATING 291 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead. ACC does not react to stationary objects and stationary vehicles.
20_BV_OM_EN_US_t.book Page 292 292 STARTING AND OPERATING General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: FCC ID: RX2TCUFCA025N IC: 4983A-TCUFCA02SN This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
20_BV_OM_EN_US_t.book Page 293 STARTING AND OPERATING Normal (Fixed Speed) Cruise Control Mode In addition to Adaptive Cruise Control mode, a Normal (Fixed Speed) Cruise Control mode is available for cruising at fixed speeds. The Normal (Fixed Speed) Cruise Control mode is designed to maintain a set cruising speed without requiring the driver to operate the accelerator. Speed Control can only be operated if the vehicle speed is above 20 mph (32 km/h).
20_BV_OM_EN_US_t.book Page 294 294 STARTING AND OPERATING To Vary The Speed Setting To Increase Speed When the Normal (Fixed Speed) Cruise Control is set, you can increase speed by pushing the SET (+) button. The driver's preferred units can be selected through the instrument panel settings. Refer to ”Instrument Cluster Display” in “Getting To Know Your Instrument Panel” for more information. The speed increment shown is dependent on the speed of U.S. (mph) or Metric (km/h) units: U.S.
20_BV_OM_EN_US_t.book Page 295 STARTING AND OPERATING • If the button is continually pushed, the set speed will continue to decrease in 5 mph decrements until the button is released. The decrease in set speed is reflected in the instrument cluster display. Metric Speed (km/h) • Pushing the SET (-) button once will result in a 1 km/h decrease in set speed. Each subsequent tap of the button results in a decrease of 1 km/h.
20_BV_OM_EN_US_t.book Page 296 296 STARTING AND OPERATING To Resume Speed REAR PARKSENSE — IF EQUIPPED To resume a previously set speed, push the RES button and release. Resume can be used at any speed above 20 mph (32 km/h). The Rear ParkSense system provides visual and audible indications of the distance between the rear fascia and a detected obstacle when backing up (e.g. during a parking maneuver). Refer to “ParkSense System Usage Precautions” for limitations of this system and recommendations.
20_BV_OM_EN_US_t.book Page 297 STARTING AND OPERATING 297 Rear ParkSense Sensors Chime The four Rear ParkSense sensors, located in the rear fascia/ bumper, monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approximately 12 inches (30 cm) up to 59 inches (150 cm) from the rear fascia/bumper in the horizontal direction, depending on the location, type and orientation of the obstacle.
20_BV_OM_EN_US_t.book Page 298 298 STARTING AND OPERATING Detection Distances If the sensors detect more obstacles, only the obstacle with the shortest distance is taken into account. Instrument Cluster Display Rear ParkSense is displayed on the instrument cluster only if you have selected "Sound and Display" within the "Safety And Driving Assistance" menu of the Uconnect system.
20_BV_OM_EN_US_t.book Page 299 STARTING AND OPERATING Rear ParkSense will remember the previous state when the ignition is placed in the OFF position. CAUTION! After turning OFF the ignition, the Rear ParkSense remains in this setting until the next ignition cycle, even in the case of changing the setting of starting RUN to OFF and then again in RUN.
20_BV_OM_EN_US_t.book Page 300 300 STARTING AND OPERATING ParkSense System Usage Precautions NOTE: • Ensure that the outer surface and the underside of the rear bumper is clean and clear of snow, ice, mud, dirt or other obstruction to keep the Rear ParkSense system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of Rear ParkSense. • Clean the Rear ParkSense sensors regularly, taking care not to scratch or damage them.
20_BV_OM_EN_US_t.book Page 301 STARTING AND OPERATING CAUTION! • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.
20_BV_OM_EN_US_t.book Page 302 302 STARTING AND OPERATING ParkSense is active when the gear selector is shifted to REVERSE or to a forward gear and an obstacle is detected, as long as the system is on. When the gear selector shifted to NEUTRAL (or PARK in case of automatic gearbox), the system becomes inactive. When the vehicle is moving forward, the system will remain active until the vehicle speed remains below approximately 11 mph (18 km/h).
20_BV_OM_EN_US_t.book Page 303 STARTING AND OPERATING ParkSense Warning Display ParkSense Display The ParkSense Warning screen will only be displayed if “Sound and Display” is selected from the Customer Programmable Features section of the Uconnect System. Refer to "Uconnect Settings” in “Multimedia” for further information. Rear Park Assist The ParkSense Warning screen is located within the instrument cluster display.
20_BV_OM_EN_US_t.book Page 304 304 STARTING AND OPERATING If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the audible chime will increase as the objects get closer to the vehicle.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 307 STARTING AND OPERATING 307 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
20_BV_OM_EN_US_t.book Page 308 308 STARTING AND OPERATING Front Park Assist The ParkSense warning screen will be displayed when the gear selector is in the DRIVE position and an obstacle is detected, as long as the vehicle speed is below approximately 11 mph (18 km/h). The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle.
20_BV_OM_EN_US_t.book Page 309 STARTING AND OPERATING 309 If an obstacle is detected in the left and/or right front region, the display will show a single flashing arc in the left and/or right front region. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the audible chime will increase as the objects gets close to the vehicle.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 311 STARTING AND OPERATING 311 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
20_BV_OM_EN_US_t.book Page 312 312 STARTING AND OPERATING Front Park Assist Audible Alerts Enabling And Disabling ParkSense ParkSense will turn off the Front Park Assist audible alert (chime) after approximately three seconds when an obstacle has been detected, and the vehicle is stationary. If the obstacle has been detected within less than 12 inches (30 cm), then the Parksense will not turn off the Front Park Assist audible alert.
20_BV_OM_EN_US_t.book Page 313 STARTING AND OPERATING 313 Service The ParkSense Park Assist System Cleaning The ParkSense System When the ParkSense System has detected a faulted condition, the instrument cluster display will actuate a single chime, and it will show the "PARKSENSE UNAVAILABLE WIPE REAR SENSORS", "PARKSENSE UNAVAILABLE WIPE FRONT SENSORS", or the "PARKSENSE UNAVAILABLE SERVICE REQUIRED" message for five seconds. Under this condition, ParkSense will not operate.
20_BV_OM_EN_US_t.book Page 314 314 STARTING AND OPERATING • Clean the ParkSense sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The ParkSense system might not detect an obstacle behind or in front of the fascia/bumper, or it could provide a false indication that an obstacle is behind or in front of the fascia/ bumper.
20_BV_OM_EN_US_t.book Page 315 STARTING AND OPERATING CAUTION! • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.
20_BV_OM_EN_US_t.book Page 316 316 STARTING AND OPERATING Arcs-Right Continuous Tone/Flashing Arcs Distance (inches/cm) Arcs-Left WARNING ALERTS Less than 12 inches (30 cm) Flashing 12–65 inches (30–60 cm) Flashing WARNING ALERTS Flashing Flashing Audible Alert Chime Continuous Radio Volume Reduced Audible chime increases as the objects within the vehicle’s path get close to the vehicle.
20_BV_OM_EN_US_t.book Page 317 STARTING AND OPERATING 317 Activation — Deactivation Operation With A Trailer The system can operate only after driving a short distance and if the vehicle speed is between 0 and 11 mph (0 and 18 km/h). The system can be activated/deactivated via the "Settings" menu of the Uconnect system. If the ParkSense System is deactivated via the ParkSense Hard switch then the side distance warning system will automatically be deactivated.
20_BV_OM_EN_US_t.book Page 318 318 STARTING AND OPERATING • Clean the ParkSense sensors regularly, taking care not to scratch or damage them. The sensors must not be covered with ice, snow, slush, mud, dirt or debris. Failure to do so can result in the system not working properly. The ParkSense system might not detect an obstacle behind or in front of the fascia/bumper, or it could provide a false indication that an obstacle is behind or in front of the fascia/ bumper.
20_BV_OM_EN_US_t.book Page 319 STARTING AND OPERATING CAUTION! • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not detected at all. Obstacles located above or below the sensors will not be detected when they are in close proximity. • The vehicle must be driven slowly when using ParkSense in order to be able to stop in time when an obstacle is detected.
20_BV_OM_EN_US_t.book Page 320 320 STARTING AND OPERATING Enabling And Disabling The ParkSense Active Park Assist System • Touching the steering wheel during active steering guidance into the parking space. The ParkSense Active Park Assist system can be enabled and disabled with the ParkSense Active Park Assist switch, located on the switch panel below the Uconnect display. • Pushing the ParkSense Front and Rear Park Assist switch.
20_BV_OM_EN_US_t.book Page 321 STARTING AND OPERATING The ParkSense Active Park Assist system will only operate and search for a parking space when the following conditions are present: • Gear position is in DRIVE. • Ignition is in the RUN position. • ParkSense Active Park Assist switch is activated. • Driver's door is closed. • Rear liftgate is closed. • Vehicle speed is less than 15 mph (25 km/h).
20_BV_OM_EN_US_t.book Page 322 322 STARTING AND OPERATING • When seeking for a parking space, the driver should drive as parallel or perpendicular (depending on the type of maneuver) to other vehicles as possible. • The feature will only indicate the last detected parking space (example: if passing multiple available parking spaces, the system will only indicate the last detected parking space for the maneuver).
20_BV_OM_EN_US_t.book Page 323 STARTING AND OPERATING Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands from the steering wheel. 323 Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed to place the gear selector into the REVERSE position.
20_BV_OM_EN_US_t.book Page 324 324 STARTING AND OPERATING When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete. Check Surroundings — Wait For Steering To Complete The system will then instruct the driver to check their surroundings and move backward.
20_BV_OM_EN_US_t.book Page 325 STARTING AND OPERATING NOTE: • It is the driver's responsibility to use the brake and accelerator during the semi-automatic parking maneuver. 325 When the vehicle has reached the end of its backward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly.
20_BV_OM_EN_US_t.book Page 326 326 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will be instructed to place the gear selector into the DRIVE position. Check Surroundings — Shift To Drive When the driver places the gear selector into the DRIVE position, the system may instruct the driver to wait for steering to complete.
20_BV_OM_EN_US_t.book Page 327 STARTING AND OPERATING The system will then instruct the driver to check their surroundings and move forward. 327 When the vehicle has reached the end of its forward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. 5 Check Surroundings — Move Forward Check Surroundings — STOP NOTE: It is the driver's responsibility to use the brake and stop the vehicle.
20_BV_OM_EN_US_t.book Page 328 328 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will be instructed to place the gear selector into the REVERSE position. When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete.
20_BV_OM_EN_US_t.book Page 329 STARTING AND OPERATING The system will then instruct the driver to check their surroundings and move backward. 329 Your vehicle is now in the parallel park position. The "Active ParkSense Complete - Check Parking Position" message will be momentarily displayed. When the maneuver is complete, the driver will be instructed to check the vehicle's parking position. If the driver is satisfied with the vehicle position, they should shift to PARK.
20_BV_OM_EN_US_t.book Page 330 330 STARTING AND OPERATING Perpendicular Parking Space Assistance Operation/ Display When the ParkSense Active Park Assist system is enabled, the “Active ParkSense Searching - Press or to Switch Maneuver” message will show in the instrument cluster display. The arrow buttons on the left side of the steering wheel can be used to switch parking maneuvers. You may switch to parallel parking, or Parallel Park Exit, if you desire.
20_BV_OM_EN_US_t.book Page 331 STARTING AND OPERATING When an available parking space has been found, and the vehicle is not in position, you will be instructed to move forward to position the vehicle for a perpendicular parking sequence. 331 Once the vehicle is in position, you will be instructed to stop the vehicle’s movement and remove your hands from the steering wheel.
20_BV_OM_EN_US_t.book Page 332 332 STARTING AND OPERATING Once the vehicle is at a standstill with your hands removed from the steering wheel, you will be instructed to place the gear selector into the REVERSE position. When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete.
20_BV_OM_EN_US_t.book Page 333 STARTING AND OPERATING The system will then instruct the driver to check their surroundings and move backward. 333 NOTE: • It is the driver's responsibility to use the brake and accelerator during the semi-automatic parking maneuver. • When the system instructs the driver to remove their hands from the steering wheel, the driver should check their surroundings and begin to back up slowly.
20_BV_OM_EN_US_t.book Page 334 334 STARTING AND OPERATING When the vehicle has reached the end of its backward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Check Surroundings — STOP NOTE: It is the driver's responsibility to use the brake and stop the vehicle. The driver should check their surroundings and be prepared to stop the vehicle either when instructed to, or when driver intervention is required.
20_BV_OM_EN_US_t.book Page 335 STARTING AND OPERATING When the driver places the gear selector into the DRIVE position, the system may instruct the driver to wait for steering to complete. 335 The system will then instruct the driver to check their surroundings and move forward.
20_BV_OM_EN_US_t.book Page 336 336 STARTING AND OPERATING When the vehicle has reached the end of its forward movement, the system will instruct the driver to check their surroundings and stop the vehicle’s movement. Once the vehicle is in a standstill condition, the driver will be instructed to place the gear selector into the REVERSE position. Check Surroundings — STOP Check Surroundings — Shift To Reverse NOTE: It is the driver's responsibility to use the brake and stop the vehicle.
20_BV_OM_EN_US_t.book Page 337 STARTING AND OPERATING When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete. 337 The system will then instruct the driver to check their surroundings and move backward.
20_BV_OM_EN_US_t.book Page 338 338 STARTING AND OPERATING Your vehicle is now in the perpendicular park position. When the maneuver is complete, the driver will be instructed to check the vehicle's parking position. If the driver is satisfied with the vehicle position, they should shift to PARK. The "Active ParkSense Complete - Check Parking Position" message will be momentarily displayed.
20_BV_OM_EN_US_t.book Page 339 STARTING AND OPERATING Exiting The Parking Space NOTE: The function does not work for exiting a perpendicular parking space, but only exiting parallel parking spaces. Activation To activate this function, push the Active ParkSense hard switch and then use the steering wheel arrow buttons to select the Parallel Park Exit feature.
20_BV_OM_EN_US_t.book Page 340 340 STARTING AND OPERATING Selection Of The Maneuver Side Use the right and left arrow buttons on the steering wheel to select between parallel or perpendicular parking mode. Then use the direction indicators (turn signals) to choose the direction that you want to perform the maneuver. During the maneuver, the system asks to shift to REVERSE, select the direction indicator in the direction you want to exit.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.
20_BV_OM_EN_US_t.book Page 346 346 STARTING AND OPERATING End Of Maneuver The semi-automatic maneuver ends when the display shows the message of a completed maneuver. At the end of the maneuver, the system gives back the vehicle control to the driver. Important Information • If the sensors undergo impact which alters their position, the system operation could be greatly affected.
20_BV_OM_EN_US_t.book Page 347 STARTING AND OPERATING • The sensors may not detect objects of a particular shape or made from particular materials (very thin poles, trailer beams, panels, nets, bushes, anti-parking posts, pavements, rubbish bins, motor vehicles, etc.). Always take great care to check that the vehicle and its path are actually compatible with the parking place identified by the system.
20_BV_OM_EN_US_t.book Page 348 348 STARTING AND OPERATING LANESENSE — IF EQUIPPED LaneSense Operation The LaneSense system is operational at speeds above 37 mph (60 km/h) and below 112 mph (180 km/h). The LaneSense system uses a forward looking camera to detect lane markings and measure vehicle position within the lane boundaries.
20_BV_OM_EN_US_t.book Page 349 STARTING AND OPERATING 349 To turn the LaneSense system off, push the LaneSense button once (LED turns on). NOTE: The LaneSense system will retain the last system state on or off from the last ignition cycle when the ignition is changed to the RUN position. LaneSense Warning Message The LaneSense system will indicate the current lane drift condition through the instrument cluster display.
20_BV_OM_EN_US_t.book Page 350 350 STARTING AND OPERATING • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes from white to gray, the left thin line remains solid white and the LaneSense telltale changes from solid white to flashing yellow. Left Lane Departure — Both Lanes Detected • When the LaneSense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected.
20_BV_OM_EN_US_t.book Page 351 STARTING AND OPERATING • When the LaneSense system senses a lane drift situation, the left thick lane line and the left thin line turn solid white. The LaneSense telltale changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. For example: If approaching the left side of the lane, the steering wheel will turn to the right.
20_BV_OM_EN_US_t.book Page 352 352 STARTING AND OPERATING NOTE: The LaneSense system operates with similar behavior for a right lane departure. Premium Instrument Cluster Display — If Equipped When the LaneSense system is on, the lane lines are gray when both of the lane boundaries have not been detected and the LaneSense telltale is solid white.
20_BV_OM_EN_US_t.book Page 353 STARTING AND OPERATING 353 Left Lane Departure — Both Lanes Detected • When the LaneSense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The LaneSense telltale is solid green when both lane markings have been detected and the system is “armed” to provide visual warnings in the instrument cluster display and a torque warning in the steering wheel if an unintentional lane departure occurs.
20_BV_OM_EN_US_t.book Page 354 354 STARTING AND OPERATING • When the LaneSense system senses a lane drift situation, the left thick lane line and left thin line turn solid yellow. The LaneSense telltale changes from solid green to solid yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. For example: If approaching the left side of the lane the steering wheel will turn to the right.
20_BV_OM_EN_US_t.book Page 355 STARTING AND OPERATING 355 Changing LaneSense Status The LaneSense system has settings to adjust the intensity of the torque warning and the warning zone sensitivity (early/ late) that you can configure through the Uconnect system screen. Refer to “Uconnect Settings” in “Multimedia” for further information. NOTE: • When enabled the system operates above 37 mph (60 km/h) and below 112 mph (180 km/h). 5 • Use of the turn signal suppresses the warnings.
20_BV_OM_EN_US_t.book Page 356 356 STARTING AND OPERATING When the vehicle is shifted out of REVERSE, a touchscreen "X" button is overlapped to the camera image in order to disable the visualization earlier than 10 seconds. When enabled, active guide lines are overlaid on the image to illustrate the width of the vehicle and its projected backup path based on the steering wheel position. Different colored zones indicate the distance to the rear of the vehicle.
20_BV_OM_EN_US_t.book Page 357 STARTING AND OPERATING 357 ADDING FUEL The Capless Fuel System uses a flapper placed at the filler pipe of the fuel tank; it opens and closes automatically upon insertion/extraction of the fuel nozzle. The Capless Fuel System is designed so that it prevents the filling of an incorrect type of fuel. Opening The Door For filling proceed as follows: 1. Open the door, by pushing and releasing on the indentation point indicated by the arrow. 5 Fuel Filler Door 2.
20_BV_OM_EN_US_t.book Page 358 358 STARTING AND OPERATING Emergency Refueling Procedure If the vehicle is out of fuel proceed as follows: • Open the liftgate and remove the emergency fuel fill funnel located in the cargo area. Filling Procedure 3. Before removing the nozzle, wait at least 10 seconds to allow the fuel to flow inside of the tank. 4. Pull the nozzle from the filler pipe and then close the door.
20_BV_OM_EN_US_t.book Page 359 STARTING AND OPERATING 359 5 Emergency Fuel Fill Funnel – If Equipped With Full Size Spare Tire • Open the fuel door. • Insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. Fueling With Emergency Fuel Fill Funnel • Remove the emergency fuel fill funnel, and close the door. • Store the emergency fuel fill funnel in the cargo area.
20_BV_OM_EN_US_t.book Page 360 360 STARTING AND OPERATING WARNING! (Continued) • Do not approach the neck of the tank with open flames or lit cigarettes its an extreme fire hazard. Also, avoid close contact with the filler pipe with your face, do not inhale harmful vapors. • Do not use your mobile phone in the vicinity of the pump fuel nozzle, it can be a possible risk of fire.
20_BV_OM_EN_US_t.book Page 361 STARTING AND OPERATING 361 Tire Size Loading The tire size on the Vehicle Certification Label represents the actual tire size on your vehicle. Replacement tires must be equal to the load capacity of this tire size. The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.
20_BV_OM_EN_US_t.book Page 362 362 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver, passengers, cargo and tongue weight.
20_BV_OM_EN_US_t.book Page 363 STARTING AND OPERATING 363 Gross Axle Weight Rating (GAWR) Frontal Area The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR. Refer to “Vehicle Loading” in “Starting And Operating” for further information. The frontal area is the maximum height multiplied by the maximum width of the front of a trailer.
20_BV_OM_EN_US_t.book Page 364 364 STARTING AND OPERATING Weight-Distributing Hitch A weight-distributing system works by applying leverage through spring (load) bars. They are typically used for heavier loads to distribute trailer tongue weight to the tow vehicle's front axle and the trailer axle(s). When used in accordance with the manufacturer's directions, it provides for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety.
20_BV_OM_EN_US_t.book Page 365 STARTING AND OPERATING 365 Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Class Trailer Hitch Classification Definitions Class I - Light Duty Max.
20_BV_OM_EN_US_t.book Page 366 366 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. (See Note) 2.4L 2,000 lbs (906 kg) 200 lbs (90 kg) 1.3L Turbo 2,000 lbs (906 kg) Refer to local laws for maximum trailer towing speeds.
20_BV_OM_EN_US_t.book Page 367 STARTING AND OPERATING Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
20_BV_OM_EN_US_t.book Page 368 368 STARTING AND OPERATING WARNING! (Continued) • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the tow vehicle. Put the tow vehicle transmission in PARK. Always block or "chock" the trailer wheels. • GCWR must not be exceeded.
20_BV_OM_EN_US_t.book Page 369 STARTING AND OPERATING Towing Requirements — Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes.
20_BV_OM_EN_US_t.book Page 370 370 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. NOTE: • Disconnect trailer wiring connector from the vehicle before launching a boat (or any other device plugged into vehicle’s electrical connect) into water. • Be sure to reconnect after clear from water area.
20_BV_OM_EN_US_t.book Page 371 STARTING AND OPERATING 371 Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic. Automatic Transmission — If Equipped Select the DRIVE range when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, if frequent shifting does occur while in DRIVE, you can use the AutoStick shift control to manually select a lower gear.
20_BV_OM_EN_US_t.book Page 372 372 STARTING AND OPERATING AutoStick Cooling System • When using the AutoStick shift control, select the highest gear that allows for adequate performance and avoids frequent downshifts. For example, choose “5” if the desired speed can be maintained. Choose “4” or “3” if needed to maintain the desired speed. To reduce potential for engine and transmission overheating, take the following actions: • To prevent excess heat generation, avoid continuous driving at high RPM.
20_BV_OM_EN_US_t.book Page 373 STARTING AND OPERATING 373 RECREATIONAL TOWING Towing This Vehicle Behind Another Vehicle TOWING CONDITION Flat Tow Dolly Tow On Trailer WHEELS OFF THE GROUND FRONT WHEEL DRIVE (FWD) REAR NOT ALLOWED ALL BEST METHOD NONE FRONT NOT ALLOWED OK FOUR-WHEEL DRIVE (4WD) NOT ALLOWED NOT ALLOWED NOT ALLOWED OK NOTE: • When towing your vehicle, always follow applicable state and provincial laws.
20_BV_OM_EN_US_t.book Page 374 374 STARTING AND OPERATING Recreational Towing Models With Front-Wheel Drive (FWD) Recreational towing is allowed ONLY if the front wheels are OFF the ground. This may be accomplished using a tow dolly (front wheels off the ground) or vehicle trailer (all four wheels off the ground). If using a tow dolly, follow this procedure: • Properly secure the dolly to the tow vehicle, following the dolly manufacturer's instructions. • Drive the front wheels onto the tow dolly.
20_BV_OM_EN_US_t.book Page 375 STARTING AND OPERATING DRIVING TIPS On-Road Driving Tips Utility vehicles have higher ground clearance and a narrower track to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them a higher center of gravity than conventional passenger cars. An advantage of the higher ground clearance is a better view of the road, allowing you to anticipate problems.
20_BV_OM_EN_US_t.book Page 376 376 STARTING AND OPERATING Flowing Water Driving In Snow, Mud And Sand If the water is swift flowing and rising (as in storm run-off) avoid crossing until the water level recedes and/or the flow rate is reduced. If you must cross flowing-water, avoid depths in excess of 9 inches (22 cm). The flowing water can erode the streambed causing your vehicle to sink into deeper water. Determine exit point(s) that are downstream of your entry point to allow for drifting.
20_BV_OM_EN_US_t.book Page 377 STARTING AND OPERATING of the engine to help regulate your speed. If the brakes are required to control vehicle speed, apply them lightly and avoid locking or skidding the tires. WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle. Always back straight down a hill in REVERSE gear carefully.
20_BV_OM_EN_US_t.book Page 378 378 STARTING AND OPERATING After Driving Off-Road Off-road operation puts more stress on your vehicle than does most on-road driving. After going off-road, it is always a good idea to check for damage. That way you can get any problems taken care of right away and have your vehicle ready when you need it. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and exhaust system for damage.
