DIGITAL COLOR PRINTER MODEL CP9000DW OPERATION MANUAL POWER DOOR OPEN ALARM PAPER/INK RIBBON DATA READY CANCEL COOLING FEED&CUT THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. This digital color printer complies with the requirements and other relevant provisions of the EC Directive 89/336/EEC, 73/23/EEC, 93/68/EEC and 1999/ 5/EC.
INFORMATION This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Use the included AC power cord so as not to interfere with radio and television reception. If you use other cables, it may cause interference with radio and television reception.
CAUTION CAUTION : TO REDUCE THE RISK OF ELECTRIC PRECAUTIONS RISK OF ELECTRIC SHOCK DO NOT OPEN SHOCK, DO NOT REMOVE COVER (OR BACK) REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The “Caution, hot surface” symbol indicates that the marked item may be hot and should not be touched.
WARNING: In the USA or Canada, use the AC power cord according to the recommendations as below, in order to comply with UL60950 and CAN/CSA C22.2 No. 60950-00. Case 1. Connect to the 120V receptacle of the room or the host equipment. The AC power cord should be UL or CSA approved and consist of type SJT or SVT, size 16 or 18AWG, length 2.5m or shorter cord with IEC320/C13 type, 125V 10A or higher rating connector and NEMA 5-15 type, 125V 10A or higher rating plug. Case 2.
CONTENTS PRECAUTIONS CONTENTS 1 2-4 5 6 7-8 FEATURES Contents ................................................................................................ Safety precautions ................................................................................ Special features .................................................................................... Unpacking ............................................................................................. Features and functions ....................
SAFETY PRECAUTIONS In the interest of safety, please observe the following precautions: POWER REQUIREMENT This Digital Color Printer is designed to operate on 120V AC 50/60Hz in U.S.A. and Canada, 220V-240V AC 50/60Hz in Europe. Never connect to any outlet or power supply having a different voltage or frequency. WARNING : THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT: CET APPAREIL DOIT ETRE MIS A LA TERRE. PROTECTIVE MEASURES IF ABNORMALITIES ARISE, .....
INSTALLATION LOCATIONS PRECAUTIONS MAINTAIN GOOD VENTILATION Ventilation slots and holes are provided on the rear and both sides of this unit. Place the unit on a hard and level surface and locate at least 10cm (4 inches) from walls to insure proper ventilation. When putting the unit on the system rack, take a space between the unit and the back and sides of the rack. UNSUITABLE LOCATIONS Avoid shaky places or hot-springs areas where hydrogen sulfide and acidic ions are likely to be generated.
SAFETY PRECAUTIONS OTHER CAUTIONS Dust or other foreign matter adhering to the print paper or the ink cassette, or deformation resulting from exposure to extremely low or high temperatures could cause loss of color, uneven color or lines, or wrinkles in the print images. NOTE: YOUR UNDERSTANDING IS REQUESTED FOR THE LOSS OF IMAGES IN MEMORY DUE TO THE SUDDEN OCCURRENCE OF A MALFUNCTION. As for Print paper and ink ribbon, refer to “PAPER / INK RIBBON SET”.
SPECIAL FEATURES PRECAUTIONS SPECIAL FEATURES TWO PRINT SIZES ARE AVAILABLE DEPENDING ON THE PURPOSE Two printing sizes, 9x13 (3.5x5”) (max.89 x 127 mm) and 10x15 (4x6”) (max.102 x 152 mm), are selectable. HIGH SPEED PRINTING Normal printing speed is approx.15 seconds (in 9x13 (3.5x5”) print). Use of roll paper shortens the time for installing and removing. FEATURES LARGE CAPACITY PRINTING Maximum of 680 prints per roll for 9x13 (3.5x5”) is offered.
UNPACKING UNPACKING Take the printer out of the box by the following procedures. Make sure to check the accessories. 1Open the top of the box. 2Remove the accessories together with upper cushions. 3Hold the handles of the cardboard and pull it up carefully to take the printer together with the lower cushions out of the box. Make sure to pull the cardboard straight up. 4Separate the printer from the cushions. Make sure to keep the printer horizontally. 5Unwrap the packing.
FEATURES & FUNCTIONS 6 4 POWER ALARM PAPER / INK RIBBON DOOR OPEN DATA READY CANCEL 10 COOLING 11 FEATURES 5 9 8 7 PRECAUTIONS FRONT PANEL 12 FEED&CUT 13 3 2 1 POWER BUTTON 9DATA INDICATOR 2 DUST BOX A READY INDICATOR Use to switch the power ON and OFF. Press to turn on power. Press again to turn off power. Holds the paper chips. When shipping, the dust box is attached to the unit with packed in a plastic bag. Take it out and mount it to the unit as the figure shows.
FEATURES & FUNCTIONS SIDE AND REAR PANEL 1 4 3 2 3 5 5 AC LINE 6 (LEFT SIDE) 1 USB TERMINAL (REAR) 2 SCSI ID SWITCH 4 DIP SWITCHES 5 HANDLE FOR TRANSPORTING 3 SCSI PORT 6 POWER SOCKET (AC LINE) Use to connect the USB cable. For setting, see page 10. Use to set the SCSI ID number of the connected device. See page 9. Use to connect this unit to a device with the SCSI interface such as personal computers. See page 9. 8 Use to set various functions of this unit. See page 11.
CONNECTIONS PRECAUTIONS CONNECTION WITH SCSI DATA SIGNAL EQUIPMENT 2 CONNECTING TO PERSONAL COMPUTER (EXAMPLE) FEATURES 1 Press the POWER button to turn on the power. 2 Press the DOOR OPEN button to open the door. 3 Set the input select switch inside this unit to SCSI. 4 Press the POWER button to turn off the power. 5 Connect the unit and the personal computer with a SCSI cable. Close the door. CONNECTIONS PREPARATION Input select switch Connect this unit to a personal computer as shown below.
CONNECTIONS CONNECTION WITH USB DATA SIGNAL EQUIPMENT 2 CONNECTING TO PERSONAL COMPUTER (EXAMPLE) 1 Press the POWER button to turn on the power. 2 Press the DOOR OPEN button to open the door. 3 Set the input select switch inside this unit to USB. Close the door. 4 Press the POWER button to turn off the power. 5 Connect the unit and the personal computer with a USB cable. Input select switch Connect this unit to a personal computer as shown below.
2 SETTING DIP SWITCHES OFF ON FEATURES 12345678 All the switches are set to OFF at the time of shipment from the factory. Turn off the power before changing the DIP switch settings. PRECAUTIONS SETTING OF DIP SWITCHES CONNECTIONS PREPARATION Switch No. Setting Function 1 OFF Auto feed & cut mode When the door is closed after the print paper or a ink cassette is installed with this unit powered on, this unit automatically carries out paper feed & cut operation.
BEFORE OPERATION Before printing, 1 Install the print paper to this unit. (pages 12-13) 2 Install the ink ribbon to this unit. (page 14-15) PAPER / INK RIBBON SET When using this unit, make sure to use the following types of the paper / ink ribbon set. 2 PAPER / INK RIBBON SET Product name Print size Number of prints Application CK9035 CK9046 9x13 (3.
PRECAUTIONS 2 Press the POWER button to turn on the power. FEATURES 3 Press the DOOR OPEN button to open the door. CONNECTIONS PREPARATION 4 Install the print paper into the unit. Make sure to install the print paper firmly. NOTE Install the print paper into the unit slowly. If it is dropped along the ditches, the unit or accessories may be damaged. TROUBLESHOOTING Paper ... as shown right. • Remove the sticker before inserting the print paper between rollers.
BEFORE OPERATION INSTALLATION OF INK RIBBON 2 INSTALLING THE INK RIBBON Before installing the ink cassette into this unit, load the ink ribbon in the ink cassette. NOTE • • Place the ink cassette on a flat surface, when loading the ink ribbon. Place the ink cassette on a flat surface, when loading the ink ribbon. • Make sure that the shafts of the ink ribbon fit into the ink cassette firmly. 1 Load the ink ribbon in the ink cassette as shown below. • Make sure to set load it in the correct position.
2 Push up the ink cassette as the arrow shows until you hear a click. PRECAUTIONS Hold the handle of the ink cassette and raise the cassette. Then put the roller ends into the ditches. Make sure to put the ivory ink ribbon roller firmly into the ditches shown by the arrows point. NOTE 1 to 2 to replace the print paper and the FEATURES If the ink ribbon is used up, repeat the steps ink ribbon. CONNECTIONS PREPARATION 3 Close the door. NOTE • • When closing the door, push it until a click is heard.
BEFORE OPERATION USAGE AND STORAGE OF PAPER / INK RIBBON SET 2 BEFORE PRINTING • • Fingerprints or dust on the paper’s printing surface may degrade the print quality and cause paper jams. If the FEED & CUT procedure is not completed when replacing the print paper, two or three prints may be printed with blank parts due to hand oil or dust.
PRECAUTIONS INSTALLATION OF PRINTER DRIVER 2 The printer driver is required to print the data from the personal computer connected with this unit. The printer driver for Windows® is supplied with this unit.
ERROR MESSAGES & COUNTERMEASURES INDICATIONS ON THE FRONT PANEL AND COUNTERMEASURES 2 If, for some reason, printing is not possible or an error occurs during printing, the indicators on the front panel will illuminate or blink. In this case, follow the procedure described below.
OVERCOMING PAPER JAMS PRECAUTIONS 1 Press the DOOR OPEN button to open the door. Make sure that the power is turned on before opening the door. If the door does not open, turn off the power and turn it on again. Then press the DOOR OPEN button again. Push down the ink cassette as shown by the arrow FEATURES 2 Remove the ink cassette. 1 and pull it out. CONNECTIONS PREPARATION 2 1 3 Take out the print paper. TROUBLESHOOTING 4 Cut off the defective part of the print paper with scissors.
ERROR MESSAGES & COUNTERMEASURES BEFORE CALLING FOR SERVICE For the following symptoms, check the unit again before calling for service. Symptom Check & Remedy The power is not turned on. Is the power cord plug disconnected from the outlet? → Connect the power cord plug to the outlet firmly. → The protective circuit may be working. Turn off the power and wait for about two minutes. Then turn on the power again. Is the image data transferred? The Door does not close. → Check the status.
CLEANING Cleaning as indicated below will help maintain stable printer operation and extend the printer’s life. A small amount of alcohol PRECAUTIONS Preparations Alcohol (isopropyl alcohol) Tissue paper (Fold in half about four times, and use the folded side to clean.) Cotton buds Cleaning part How to fold tissue paper Other : Cleaner pen (option)* 1 Press the POWER button to turn on the power. 2 Press the DOOR OPEN button to open the door. FEATURES * Please ask the dealer about options.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. 9351 Jeronimo Road, Irvine, CA 92618, U.S.A. Phone 949-465-6000 Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Herts. AL10 8XB, England, U.K. Phone (0) 1707 276100 FAX (0) 1707 278755 German Branch Gothaer Strasse 8, 40880 Ratingen ; Postfach 1548, 40835 Ratingen ; Germany Phone 02102/ 486-9250 FAX 02102/ 486-7320 French Branch 25, Boulevard des Bouvets - 92741 NANTERRE cedex Phone (01) 55.68.55.00 FAX (01) 55.68.57.