Installation Guide
N664
Dashcam
Installation Guide
I. What's in the Box
•
Dash cam with front and interior-facing cameras
•
Rear mounting plate with adhesive tape
•
Top cover
•
Cable cap
•
Y-cable
•
OBD-II cable
•
10-pin to open end cable
•
Rear recording camera with cable (selected models only)
II. Product Overview
1
Reset button
9
Emergency recording
indicator/button
2
SIM card slot
q
WIFI/mobile broadband
indicator
3
MicroSD slot
w
Infrared illuminator (x4)
4
Rear camera connector
e
Interior-facing camera
5
Charging/data port
r
Speaker
6
NFC sensor
t
Mounting slot (x3)
7
Camera locking screw
(x2)
y
Front-facing camera
8
Microphone (x2)
III. Device Installation
Precautions and notices
•
For your own safety, do not operate the controls of the
product while driving. Using this product does not exempt
the driver from taking full responsibility for his/her driving
behaviour, which includes observing all trac rules and safety
regulations.
•
Make sure the dash cam is positioned in a way that does not
obstruct the driver’s view or airbag deployment.
•
Make sure that no object is blocking the camera lens and no
reective material appears near the lens. Please keep the
lens clean.
•
Video quality may be degraded if the vehicle’s windscreen is
tinted.
•
If the car’s windscreen is tinted with a reective coating, its
surface may be athermic and impact GPS reception. In this
instance, please mount the device in a “clear area”.
•
The device will automatically calibrate its G-sensor during
start-up. Always turn on the device after it is mounted in place
to avoid G-sensor malfunction.
Mounting the dash cam
•
The dash cam should be placed near the rear-view mirror to
ensure the highest video quality, but never position the device
where the driver’s eld of vision is blocked.
•
When adjusting the dash cam’s viewing angle, make sure
the vehicle is parked on level ground and the camera’s view
is parallel to the ground. The ground to sky ratio should be
approximately 6 to 4.
Note:
l
Cleaning the windscreen with rubbing alcohol before
mounting the dash cam is highly recommended.
l
The double-sided adhesive tape can be replaced if it is no
longer adhering to the windscreen properly.
SIM and memory cards
A MicroSD card (up to 256GB in capacity) and a Nano SIM
card must be inserted prior to mounting the dash cam on the
windscreen.
It is very important to use a MicroSD card specically designed
to be used in dash cameras. It ensures the card will be more
reliable and last longer; the wrong type of card has a greater
chance of failing, even after a short period of time.
To insert a card, hold each card by the edges and gently insert it
into the slot as shown in the illustration. To remove a card, gently
push the top edge of the card inwards to release it and pull it out
of the slot.
1. Route the Y-cable inside the vehicle, leaving the main
connector exposed at where the dash cam is to be installed
on the windscreen and the other end going toward the
vehicle's OBD-II port.
2. Peel the lm o from the back of the rear plate.
3. Ax the rear plate securely onto the windscreen.
4. Attach the dash cam to the rear plate by matching the
positions of the three mounting holes on the back of the
camera with the hooks on the rear plate. Slide the dash cam
to the left to lock it in place.
5. Connect the main connector to the dash cam. If your product
includes a rear recording camera, connect the rear camera
cable to the mini-USB port as shown.
6. Attach the top cover to the dash cam and tighten the screw
with an M2 hex key.
7. Cover exposed cables coming out the dash cam with the
cable cap. The rubber cap can be trimmed to desired length
with a pair of scissors.
8. Plug the OBD-II connector into the vehicle's OBD-II port and
use the following table to connect the colour-coded open
wires:
Colour Connection
Red Accessory (ACC)
Orange Reverse
Yellow Input
Green RS232 TX Out (to vehicle)
Blue Speed pulse
Purple Input
Brown Input
Grey Output
Black Ground
White RS232 TX In (to dash cam)
The following is a complete connection diagram:
9. Adjust the viewing angle of the front and interior facing
cameras by loosening the corresponding locking screw with
an M2 hex key. Tighten the locking screws once the viewing
angles are set.
Rear recording camera
A rear recording camera is included with selected models. Before
installing the rear recording camera, please wipe the surface
clean with rubbing alcohol. Select a suitable location for mounting
the rear recording camera so that the driver's eld of vision is not
obscured.
1
Camera lens
2
Mounting base
3
Micro-USB port
One end of the rear camera cable should already be connected
to the dash cam (see step No. 5 of the installation instructions).
Once the rear camera is mounted in the appropriate location,
connect the other end of the cable to the rear camera's micro-
USB port.
IV. LED Indicators
Recording/emergency recording LED:
Behaviour Indication
Red, always on Normal recording in progress
Red, blinking slowly Emergency recording in progress
Red, blinking rapidly Memory card error
WIFI/mobile broadband LED:
Behaviour Indication
Cyan System initializing
Green, always on WIFI connected
Blue, always on Mobile broadband connected
Blue, blinking Mobile broadband disconnected
V. For more information
Caring for your device
l
Taking good care of your device will ensure trouble-free
operation and reduce the risk of damage.
l
Keep your device away from excessive moisture and
extreme temperatures.
l
Avoid exposing your device to direct sunlight or strong
ultraviolet light for extended periods of time.
l
Do not place anything on top of your device or drop objects
on your device.
l
Do not drop your device or subject it to severe shock.
l
Do not subject your device to sudden and severe
temperature changes. This could cause moisture
condensation inside the unit, which could damage your
device. In the event of moisture condensation, allow the
device to dry out completely before use.
l
Never attempt to disassemble, repair or make any
modications to your device. Disassembling, modifying or
any attempt to repair could cause damage to your device,
may inict bodily harm or damage to property and will void
any warranty.
l
Do not store or carry ammable liquids, gases or explosive
materials in the same compartment as your device, its parts
or accessories.
l
To discourage theft do not leave the device and accessories
in plain view in an unattended vehicle.
l
Overheating may damage the device.
About GPS
l
GPS (Freq=1575.42MHZ) is operated by the United States
government, which is solely responsible for the performance
of GPS. Any change to the GPS system can affect the
accuracy of all GPS equipment.
l
GPS satellite signals cannot pass through solid materials
(except glass). When you are inside a tunnel or building,
GPS positioning is not available. Signal reception can
be affected by situations such as bad weather or dense
overhead obstacles (e.g. trees, tunnels, viaducts and tall
buildings).
l
The GPS positioning data is for reference only.
Regulatory Information
For regulatory identication purposes, the device is assigned a
model number of N664 / Dashcam.
Federal Communication Commission Interference
Statement
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution: Any changes or modications not expressly
approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes : 1) L’appareil ne doit pas produire
de brouillage; 2) L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This device has been tested and meets applicable limits for
Radio Frequency (RF) exposure. This equipment should be
installed and operated with minimum distance 30 cm between
the radiator and your body.
USA Contact Information
Magellan
279 E Arrow Highway San Dimas, CA 91773 USA
+1 909-394-5000
http://www.magellangps.com
CE
Products with the CE marking comply with Radio Equipment
Directive (Directive 2014/53/EU) - issued by the Commission of
the European Community.
Compliance with these directives implies conformity to the
following European Standards:
• EN 301 489-1 V2.2.3 (2019-11)
• EN 301 489-3 V2.1.1 (2019-03)
• EN 301 489-17 V3.1.1 (2017-02)
• EN 301 489-19 V2.1.1 (2019-04)
• Draft EN 301 489-52 V1.1.0 (2016-11)
• EN 55032:2015+AC:2016, Class B
• EN 55035:2017
• EN 50498:2010
• ISO 7637-2:2004
• EN 300 328 V2.2.2
• EN 300 440 V2.1.1; 2017
• IEC60950-1(ed.2); am1; am2
• IEC62368-1:2014 (EN62368-1:2014/A11:2017)
The manufacturer cannot be held responsible for modications
made by the User and the consequences thereof, which may
alter the conformity of the product with the CE Marking.
Declaration of conformity
Hereby, MiTAC declares that this N664 is in compliance with the
essential requirements and other relevant provisions of Directive
2014/53/EU.
Maximum power for each band
• LTE-FDD: B1/ B2/ B3/ B4/ B5/ B7/ B8/ B20/ B28 (25dBm)
• LTE-TDD: B38/ B39/ B40/ B41 (25dBm)
• WCDMA: B1/ B2/ B4/ B5/ B8 (25dBm)
• GSM/EDGE: 850/900/1800/1900MHz (32dBm)
About WIFI
• Frequency: 2412 – 2472MHZ
• Max. power = 18dbm
About BT
• Max. power = 11dBm
WEEE
This product must not be disposed of as normal household
waste, in accordance with the EU directive for waste electrical
and electronic equipment (WEEE – 2012/19/EU). Instead, it
should be disposed of by returning it to the point of sale, or to a
municipal recycling collection point.