Disclaimer Notes A105 Series User Manual
en Welcome Thank you for purchasing a Mio product. This Quick Start Guide guides you through the successful setup of your device and familiarizes you with the basic skills of using the device. Knowing your device 1. LED indicator 1 (Barcode reader status) 2. LED indicator 2 (Battery charge status) 3. Barcode reader 4. POWER button 5. Barcode reader button 6. Speaker 7. Rear camera 8. Flash 9. Front camera 10. Microphone 11. Micro-USB port 12. HD connector 13. Dock connector (selected models only) 14.
en Getting started Charging the battery Your device has an internal battery that may not be fully charged when you purchase it. You should charge the battery for at least 8 hours before you start using it for the very first time. To charge the battery, plug the home charger cable into the Micro-USB connector on the bottom of your device and the mains power charger into the power socket.
en Performing the initial start-up 1. Press and hold the POWER button until the device turns on. 2. The Home screen will be displayed and the device is in Lock mode by default. 3. To unlock the device, drag the Lock icon ( ) to the right. You can now use your device.
en Installing the memory card 1. Open the cover on the left side of the device to locate the memory card slot. 2. Hold the microSD card by the edges and gently insert it into the slot with the label facing the back of your device. CAUTION! Do not apply pressure to the centre of the memory card. 3. To remove a card, gently push the top edge of the card inwards to release it, and pull it out of the slot. IMPORTANT! Before removing the memory card, you are recommended to unmount it from the system.
en Operating basics Using the POWER button • Turning on the device Press and hold the POWER button until the device turns on. • Switching on/off the screen Your device will automatically switch off the screen after 1 minute (by default) of inactivity. You can manually switch off the screen by pressing the POWER button briefly. To turn the screen on, press the POWER button briefly and then unlock the device by dragging the Lock icon ( ) to the right.
en Navigating on the screen To operate your device, touch the screen with your fingertip. You can perform the following actions: • Tap Touch the screen once with your fingertip to open items or select onscreen buttons or options. • Tap and hold Tap and hold on the desired item to open the pop-up menu that contains the available options for the item. • Drag Tap and hold on the item and then move it to the target position without releasing your fingertip.
en Home screen The Home screen is your starting place for tasks, providing quick access to frequently used applications and settings. Tip: To display the Home screen, tap the HOME button at any time.
en Customising your device You can customize the device through the Settings menu, including personalising the Home screen, changing the display and sound settings, configuring the connection settings, and more. Accessing the Settings menu From the desktop, do one of the following to access the Settings menu: • Tap the All Applications button ( • Tap ) > Settings. from the Quick Launcher. Getting connected Your device can access the Internet through wireless networks.
en 4. When your device is connected to a wireless network, the WLAN icon ( ) will appear in the Status Bar indicating the signal strength (number of bands that light up). The next time your device connects to a previously accessed secured wireless network, you will not be prompted to enter the WEP key again, unless you reset your device to its factory default settings. • Bluetooth Bluetooth on your device operates in three different modes: • Off: (default) Bluetooth is turned off.
en Configuring the barcode reader From the desktop, do one of the following to access the Barcode reader configuration utility: • Tap the All Applications button ( • Tap ) > Barcode Reader Config. from the Quick Launcher. By using the configuration utility, you can: • Tap the CONFIG tab and then enable/disable the barcode reader of the device by selecting/ clearing the Enable option. • Tap the CONFIG tab and then set up the barcode reader functions, including: Key Message, Read Mode, and Read Time.
en For more information Support For initial support, contact your IT department or your local authorized dealer. Occasionally, Mio may offer free system updates to improve user experience. Please regularly check the website http://miocare.mio.com/ for more information. Federal Communication Commission Interference Statement Note: For regulatory identification purposes, MioCARE A105 is assigned a model number of N406. This device complies with part 15 of the FCC Rules.
en The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves.
en Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
Disclaimer Specifications and documents are subject to change without notice. Mio Technology does not warrant this document is error-free. Mio Technology assumes no liability for damage incurred directly or indirectly from errors, omissions, or discrepancies between the device and the documents. Notes Not all models are available in all regions. Depending upon the specific model purchased, the color and look of your device and accessories may not exactly match the graphics shown in this document.