Assembly Instruction

ManualsBrandsMistana ManualsCeiling LightsFerris 6 - Light Kitchen Island Linear Pendant

1of3

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Mounting Ball

Ceiling

Canopy

Fixture Chain

Quick Link

Upper

Assembly

Fixture Body

STEP 2 Install Nipple to Crossbar-

A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the

Lock Washer (BB) over the Nipple (DD) and then thread the Nipple

(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”

above the Crossbar (AA).

B. Place the Ceiling Canopy (HH) over the Nipple (DD) against the

ceiling to determine the correct position of the Nipple (DD). Thread

the Lock Ball (EE) onto the Nipple (DD). Adjust the Nipple (DD) to

allow the Ceiling Canopy (HH) to rest against the ceiling when held

in place by the Lock Ball (EE).

C. Remove the Ceiling Canopy (HH) and then tighten the Hex Nut (CC)

against the Crossbar (AA) to secure in place.

Figure 2

(6)CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Glass Panel

Lock Screw

x12

Rubber Washer

x12

STEP 1 - Install the Crossbar to the junction box

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug.

Figure 1

Outlet Box

Outlet Box Screw

(not included)

Assembly Instruction Sheet

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (6) Candelabra Base Bulbs 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 3 - Install Upper Assembly to Fixture Body STEP 5 - Attach the Lanyard A. Unlock the screw on the hook until there is enough space for the loop end of the side rod. Attach the end of the side rod to the hook on the top of the Fixture Body (B) and tight the screw on the hook to prevent the side rod slip out of the hook. A. The purpose of the lanyard is to provide a means to support the fixture hands free from the junction box while connecting the electrical wires. B.
PAGE 3
STEP 8 - Install Glass Panels and Bulbs A. Align holes on the Glass Panel (D) to mounting holes on the frame of the Fixture Body (C). Place the Rubber Washer (F) onto the Lock Screw (E) and thread Lock Screws with Rubber Washers into the mounting holes on the frame to secure the Glass Panel (D). Hand tighten until snug. B. Insert bulbs onto sockets and screw snugly into place. Bulb (not supplied) C F Your fixture is now assembled and ready to use.