DENSITÉ series IRD-3111 SD MPEG Receiver/Decoder with ASI and RF Inputs Guide to Installation and Operation M907-9600-100 18 Jan 2011 Miranda Technologies Inc. 3499 Douglas-B.-Floreani St-Laurent, Québec, Canada H4S 2C6 Tel. 514-333-1772 Fax. 514-333-9828 www.miranda.com © 2011 Miranda Technologies Inc.
GUIDE TO INSTALLATION AND OPERATION Electromagnetic Compatibility This equipment has been tested for verification of compliance with FCC Part 15, Subpart B requirements for Class A digital devices. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
GUIDE TO INSTALLATION AND OPERATION Table of Contents 1 IRD-3111 SD MPEG Decoder with ASI and RF inputs ............................................................ 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 2 Installation .................................................................................................................................. 6 2.1 2.2 2.3 2.4 3 Installation in the Densité frame..........................................................................................................
GUIDE TO INSTALLATION AND OPERATION 4.6 4.7 5 About AFD processing....................................................................................................................... 45 Using the TS Probing Option ............................................................................................................. 49 Specifications ..........................................................................................................................
GUIDE TO INSTALLATION AND OPERATION 1 IRD-3111 SD MPEG Decoder with ASI and RF inputs 1.1 Using this Manual The IRD-3111 comes in three versions: IRD-3111-VQ IRD-3111-DVB-S2 IRD-3111-DVB-S2-CI ATSC Tuner DVB-S2 Tuner DVB-S2 Tuner with Conditional Access Module All three are described in this manual. For convenience, any description that applies to all three variants will use the term IRD-3111.
GUIDE TO INSTALLATION AND OPERATION Conditional Access • DVB-CI common interface slot allow insertion of CAM card • Allow descrambling of multiple programs encrypted by leading DVB Conditional Access Systems • Supports BISS-1 RF Input Monitoring • Automatic detection of RF loss • Convenient auto-scan mode for detection of valid signals • Monitoring of input signal strength, bit error rate (BER) and carrier to noise ratio (CNR) Easy Input and Program Selection • Manual or automatic input selection mode • Au
GUIDE TO INSTALLATION AND OPERATION • • • o Sample rate detection o Bit rate reporting Support for Secondary Audio Program (SAP) Configurable Dolby Digital dynamic range and compression Dolby Metadata embedding on SDI Metadata Extraction, Display and Embedding The following can be extracted from the TS and embedded in the HD/SD-SDI signal: o EIA-608 and EIA-708 closed captioning o WST teletext o SMPTE 12M Time code SMPTE 2016 AFD flag Extensive PSIP data extraction, including: o Time and date and other S
GUIDE TO INSTALLATION AND OPERATION 1.5 Block Diagrams The following block diagrams show the functionality of the IRD-3111. Figure 1.
GUIDE TO INSTALLATION AND OPERATION 1.6 Front Card-edge Interface The front card-edge of the IRD-3111 incorporates two elements: Status LED (see section 3.2) Select Button (see section 3.3) Status The CAM module and tuner are not shown in this view. Select • • IRD-3111 Select Button Status LED Figure 1.2 Front card-edge layout 1.
GUIDE TO INSTALLATION AND OPERATION 2 Installation 2.1 Installation in the Densité frame The IRD-3111 and its associated rear connector rear panel must be mounted in a Densité3 frame. It is not necessary to switch off the frame’s power when installing or removing the card. See the Densité3 Frame manual for detailed instructions for installing cards and their associated rear panels. 2.
GUIDE TO INSTALLATION AND OPERATION • HD/SD OUT 1 & 2 – HD/SD-SDI output The IRD-3111 provides two identical HD/SD SDI video outputs on BNC connectors. The SDI video signals conform to the SMPTE 292M and SMPTE 259M-C standards. HD signals are only available when the Up Conversion option is activated.
GUIDE TO INSTALLATION AND OPERATION 3 Operation 3.1 Control options The IRD-3111 can be controlled in two different ways: • The local control panel and its push-buttons can be used to move through a menu of parameters and to adjust parameter values (see section 3.3). • Miranda’s iControl system can be used to access the card’s operating parameters from a remote computer, using a convenient graphical user interface (GUI). (see section 3.4) 3.
GUIDE TO INSTALLATION AND OPERATION 3.3 Local control using the Densité frame control panel 3.3.1 Overview Push the SELECT button on the IRD-3111 card edge (Section 1.6) to assign the local control panel to operate the IRD-3111. Use the control panel buttons to navigate through the menu, as described below. All of the cards installed in a Densité frame are connected to the frame’s controller card, which handles all interaction between the cards and the outside world.
GUIDE TO INSTALLATION AND OPERATION 3.4 Remote control using iControl The operation of the IRD-3111 may be controlled using Miranda’s iControl system. • • This manual describes the control panels associated with the IRD-3111 and their use. Please consult the iControl User’s Guide for information about setting up and operating iControl. In iControl Navigator or iControl Websites, double-click on the IRD-3111 icon to open the control panel. 3.4.
GUIDE TO INSTALLATION AND OPERATION Icon #2 – TS Input status Transport Stream detected and OK.
GUIDE TO INSTALLATION AND OPERATION No signal (gray) Icon #6 – Secondary Audio status OK (green) No audio in program (yellow) No signal (gray) Icon #7 – Audio Sync Locked with Video (green) Free run (yellow) N/A (gray) Icon #8 – TS Limit No errors (green) Errors detected (red) No transport stream (gray) Icon #9 – Reference Locked to external reference (green) • Mouse-over the icon to see a description of the reference in use Reference missing (red) 12 | IRD-3111
GUIDE TO INSTALLATION AND OPERATION Frame sync option disabled (gray) Icon #10 – Color Bars Color bars OFF (green) Color bars ON (yellow) Icon #11 – Metadata Insertion No AFD / Dolby / Timecode / Teletext insertion conflicts (green) AFD / Dolby / Timecode / Teletext insertion conflicts (yellow) Move the mouse over an icon and a status message appears below the icon providing additional information. If there is an error, the error status message appears in the message area without mouse-over.
GUIDE TO INSTALLATION AND OPERATION 3.4.2 The Input panel This panel provides resources for input configuration and monitoring. Input section Use the Desired radio buttons to select the input. Available options are: • ASI1 – ASI input • Tuner – The built-in ATSC or DVB-S/S2 tuner • Ethernet – the data stream arriving on the rear-panel Ethernet port (only available when it is in Input mode) • AUTO – select the first valid input, prioritized as listed here (i.e.
GUIDE TO INSTALLATION AND OPERATION 3.4.3 Tuner panels The Tuner panel that appears will match the tuner type installed in the IRD-3111. 3.4.3.1 The Tuner ATSC panel (IRD-3111-VQ models only) This panel identifies the tuner type and demodulation type, and provides status icons for RF Signal Presence and RF Signal Lock. Incoming signal quality is measured using two parameters: • BER (bit error rate) • CNR (carrier-to-noise ratio) The signal status is indicated by a color-coded bar graph.
GUIDE TO INSTALLATION AND OPERATION Frequency Selected: Nominal frequency for the channel. This value is calculated from the carrier’s published frequency for the desired service on the satellite, and the conversion factor for the LNB (Low Noise Block) downconverter that is in use, and entered into this panel manually (NB. see section on Presets below).
GUIDE TO INSTALLATION AND OPERATION The chart shows what combination of signals results in the application of which input channel to the IRD-3111 inputs: Applied DC voltage Tone 13 V 18V OFF 9.75 MHz / vertical 9.75 MHz / horizontal ON 10.6 MHz / vertical 10.6 MHz / horizontal Voltage: use the pulldown to select the voltage: [OFF, 13V, 18V] Overload: the icon is red when overload exists. Tone: Use the radio buttons to turn the tone ON or OFF.
GUIDE TO INSTALLATION AND OPERATION CA Systems: The CA system that is used with the associated program CAM Interface: The section of the panel allows the user to query the CAM card and set up its operation Click Activate to start the process, and then follow the instructions that appear in the panel.
GUIDE TO INSTALLATION AND OPERATION 3.4.6 The Decoder panel The decoder panel gives the user the resources to select the program that will be decoded by the IRD-3111. Config section: Service Select – use the pulldown to select the service from among those in the transport stream A small lock icon to the left of the service number indicates that the signal is encrypted. Audio1 & Audio 2 – Use the pulldowns to select the audio 1 and 2 PIDs from the available channels.
GUIDE TO INSTALLATION AND OPERATION 3.4.7.1 AFD tab Mode Use the AFD Mode pulldown to select the operating mode • Auto • Manual Config Use the Insertion pulldown to select whether AFD information will be inserted in the output. • OFF • AFD Insertion Line: The Insertion line is used to select on which line in the VANC the AFD packet (SMPTE 2016) will be inserted. It is not necessary to specify the detection line since the card will automatically detect the incoming packet.
GUIDE TO INSTALLATION AND OPERATION 3.4.7.2 Metadata / Metadata tab This panel provides the resources to configure metadata processing on this IRD-3111. Closed Caption Section: Closed Caption • ON • OFF Note: for CVBS output, CC is always on, and not affected by this control V-Chip Mode Use the pulldown to select how V-Chip data will be processed in the IRD-3111: • Replace: Will use the PSIP information to replace any existing XDS data. Use this option if you know you want to use the PSIP advisory.
GUIDE TO INSTALLATION AND OPERATION 3.4.7.3 Metadata / Dolby tab This tab provides resources for configuring Dolby metadata insertion in the output SDI data stream. Inserter Config Insertion – use the pulldown to turn Dolby metadata insertion ON or OFF Insertion Line – use the pulldown to select the insertion line.
GUIDE TO INSTALLATION AND OPERATION 3.4.7.5 CVBS tab This tab contains controls to configure the analog video output signal. Blanking Mode Use the pulldown to select whether the blanking on the output signal will be narrow or wide Luma Range Use the pulldown to choose whether to restrict the Luma signal range to normal limits, or to allow super whites and blacks (i.e. a much expanded range).
GUIDE TO INSTALLATION AND OPERATION 3.4.9 The Audio Config panel This panel provides controls for configuring the Dolby AC3 decoder and analog audio outputs, and for monitoring some audio parameters 3.4.9.
GUIDE TO INSTALLATION AND OPERATION 3.4.9.2 Status tab This tab contains text boxes and status icons that indicate the current status of the IRD-3111’s audio processing. Audio 1 and Audio 2 are shown in separate columns • • • • • Audio presence (status icon) Audio PID Audio Type Sample Rate Output Mode AC3 Audio Status (BSI) • Service (bsmod) • Coding Type (acmod) • Bit Rate • LFE presence (status icon) • Dialnorm 3.4.
GUIDE TO INSTALLATION AND OPERATION 3.4.11 The Reference panel NOTE: The OPT-FS option must be purchased in order to enable this panel. Otherwise the reference is always taken from the input signal. The IRD-3111 output signals should always be genlocked to some reference source. The genlock source is selected in the Reference control panel.
GUIDE TO INSTALLATION AND OPERATION 3.4.12 The Probing panel 3.4.12.1 Structure tab Shows the structure of the transport stream Click on the nodes in the tree to expand it to examine areas of interest, Figure 3.20 Probing panel – Structure tab 3.4.12.2 TR 101 290 tab This tab shows the results of the tests against the TR 101 290 standard. Click in the checkbox at the bottom to enable or disable display updating (about once per second).
GUIDE TO INSTALLATION AND OPERATION 3.4.12.3 Unref_PID tab This tab provides a list of all unreferenced PIDs found in the incoming service. Figure 3.22 Probing panel – Unref_PID tab 3.4.12.4 Pie Chart tab This tab displays the incoming service in the form of a pie chart, with color-coded segments representing the various elements in the service. • This representation illustrates the bandwidth distribution within the service.
GUIDE TO INSTALLATION AND OPERATION 3.4.12.5 PSIP tab This tab is an information-only tab that documents various aspects of the incoming service (Shown for ATSC input via the ASI input only; tab will not be available when DVB-S2 from the tuner input is selected) Figure 3.24 Probing panel – PSIP tab 3.4.13 The Test panel Use the Color Bars checkbox to turn the Test function ON or OFF • When checked, the output signal is replaced by Color Bars.
GUIDE TO INSTALLATION AND OPERATION 3.4.14 The Network Settings panel Settings tab ETH Port Status The status of the ethernet link is shown by the icons: • Link is down (red) • Link is OK (green) NOTE: This is the equivalent to the green LED on the rearpanel ETH connector. ETH Port Direction Use the pulldown to select the Ethernet port functionality.
GUIDE TO INSTALLATION AND OPERATION This is the port on which the signal is present. This is valid for either transmitting or receiving. If this port does not correspond to the source, no signal will be received. Enter the new values directly into the data boxes. The changed data will show in red. • Press Apply to apply the new values, or Cancel to leave the current values unchanged. Encapsulation Select the IP protocol to use to stream packets.
GUIDE TO INSTALLATION AND OPERATION 3.4.15 The Factory/Presets panel This panel provides resources for saving, restoring and transferring the configuration settings of this IRD-3111. Load Factory The IRD-3111 maintains a “Factory Default” alignment in its memory, to which it can be restored at any time. • Click the Load Factory button to restore the card to its Factory default alignment. User Presets The User Preset controls allow the user to save and recover all configuration settings on the card.
GUIDE TO INSTALLATION AND OPERATION Copy Profile From: This section shows this IRD-3111 card, and identifies it by App server, Densité frame and slot number, card type and firmware version. The Profile column has a pulldown that allows you to select which profiles you will work with, and gives these choices: • Current, User1, User2, User3, User4, User5, ALL The Select column includes a checkbox, preselected as checked, to confirm that you want to work with the current card Figure 3.
GUIDE TO INSTALLATION AND OPERATION Copy profile to section This line shows other IRD-3111 cards that are available on the iControl network, each identified by App server, Densité frame and slot number, card type and firmware version. The Profile column shows the same information as is shown for the current card in the Copy profile from line, i.e.
GUIDE TO INSTALLATION AND OPERATION Up Conversion option This option enables up-conversion (SD-to-HD) functionality on the IRD-3111. To activate this option, you must: • Obtain a licence key from Miranda Technologies Inc. • Type the licence key in the box • Click on ENABLE OPTION to enable the option’s features. The information window beneath the key entry box indicates whether the option is activated (green) or not (gray). Figure 3.
GUIDE TO INSTALLATION AND OPERATION TS Probing option This option activates the Transport Stream probing functions of the IRD-3111. To activate this option, you must: • Obtain a licence key from Miranda Technologies Inc. • Type the licence key in the box • Click on ENABLE OPTION to enable the option’s features. The information window beneath the key entry box indicates whether the option is activated (green) or not (gray). Figure 3.36 Options panel – TS Probing Dolby 5.
GUIDE TO INSTALLATION AND OPERATION ETH option This option enables the ethernet port on the rear panel of the IRD-3111. To activate this option, you must: • Obtain a licence key from Miranda Technologies Inc. • Type the licence key in the box • Click on ENABLE OPTION to enable the option’s features. The information window beneath the key entry box indicates whether the option is activated (green) or not (gray). Figure 3.38 Options panel - ETH 3.4.
GUIDE TO INSTALLATION AND OPERATION Levels associated with these alarms: The pulldown lists may contain some or all of the following options: The alarm makes no contribution (black icon) The alarm is of minor importance (yellow icon) The alarm is of major importance (orange icon) The alarm is of critical importance (red icon) The alarm exists but has no effect (used for text and composite alarms) Shortcut: if you click in one of the Set All boxes beside a section heading, you will open a pulldown that lets
GUIDE TO INSTALLATION AND OPERATION Copy to other cards Click this button to open a panel that allows the alarm configuration set for this card to be copied into another IRD-3111 card. • Select one or more destination cards from the list in the window by clicking in the checkboxes, or all of them by clicking in the All checkbox • Note that when you do a Copy Profile for this card (see Sect.3.4.15), the alarm configuration is copied along with all the other settings. Figure 3.
GUIDE TO INSTALLATION AND OPERATION 3.4.18 The Info panel 3.4.18.1 Info tab When the IRD-3111 is included in an iControl environment, certain information about the card should be available to the iControl system. The user can enter labels and comments that will make this card easy to identify in a complex setup. This information is entered via the Info control panel. This panel also shows other information about the card.
GUIDE TO INSTALLATION AND OPERATION • Remote System Administration – opens the Joining Locators data box, which lists remote lookup services to which this IRD-3111 is registered. Add: Force the iControl service for this IRD-3111 to register itself on a user-specified Jini lookup service, using the following syntax in the data box: jini:// where <ïp_address> is the ip address of the server running the lookup service, e.g.: Figure 3.
GUIDE TO INSTALLATION AND OPERATION When you click the button, you will be presented with a dialog allowing you to confirm your decision to reset, or to cancel the reset.
GUIDE TO INSTALLATION AND OPERATION 4 User Reference Guide 4.1 Decoding MPEG Transport Streams The user can input DVB-ASI signals up to 80Mbps on either ASI input connector. Alternatively, the Ethernet can be configured to receive an IP stream (see section 3.4.14). To select an input, go to the Input Menu into Input Selection. Once a valid transport stream signal enters the decoder, the first valid service found is decoded automatically if no selection was previously made.
GUIDE TO INSTALLATION AND OPERATION The following audio coding formats are currently supported: • • • • AC3 audio up to 5.1 channels MPEG1 Layer II MPEG2 Audio AAC audio (2 CH only) The first audio can be embedded as 5.1 discrete channels (the Dolby option is required to get discreet channels; otherwise you get 2 down-mixed channels) while the second audio is always output as 2 channels. Downmix mode can be selected between Lt/Rt or Lo/Ro modes independently for both audios.
GUIDE TO INSTALLATION AND OPERATION Replace: Will use the PSIP information to replace any existing XDS data. Use this option if you know you want to use the PSIP advisory. Pass: If XDS data is already present, it is left untouched. In this mode, no V-CHIP is generated if no XDS data is present. Note that the PSIP RTT tables are not extracted. The rating information comes from the standard MPAA and other North American rating systems.
GUIDE TO INSTALLATION AND OPERATION In any case, the embedded AFD flag at the output follows any transformation that might have occurred. Therefore should the picture be rescaled, the embedded AFD reflects the actual status of the picture at the output. For example, an MPEG signal in full 16:9 (AFD code 8) down converted to SD 4:3 in letterbox will have the AFD flag 10 inserted to signal letterbox. Some restrictions apply to firmware revisions less than 211.
GUIDE E TO INSTALL LATION AND OPERATION N Inp put signal 4:3 Output sign nal 1 16:9 4 Full frame im 4:3 mage in a 4:3 frame f 4:3 3 Full frame im mage in a 4:3 fra ame 4:3 Pillar-box imag ge in 16:9 fram me (4:3_8) 4:3 Full frame im 4 mage in a 4:3 frame f (use preferred 4:3_8 4 code instead) ( (4:3_8) 4:3 3 Full frame im mage in a 4:3 fra ame (16 6:9_9) 4:3 Pillar-box imag ge in 16:9 fram me ( (4:3_9) (16 6:9_9) (4:3_9) 1 16:9 Letterbox image in 4:3 fra ame 16 6:9 Letterbox im mage in 4:3 fra
GUID DE TO INSTA ALLATION AN ND OPERATIION Input signal s 4:3 3 Ou utput signal 16:9 16:9 Full F frame imag ge in a 16:9 fra ame (use preferred p 16:9_ _8 flag instead) 16:9 Le etterbox image e in 4:3 frame 16:9 Fulll frame image in a 16:9 frame e (16:9 9_2) 14:9 Pillar-box P imag ge in a 16:9 fram me (use e preferred 16:9 9_11 flag inste ead) (4:3_10) etterbox image e in a 4:3 frame e 14:9 Le 2) (16:9_2 14:9 Pillar-box image in a 16:9 frame e (16:9 9_3) > 16:9 9 Letterbox (ce enter) image in a 1
GUIDE E TO INSTALL LATION AND OPERATION N Inp put signal 4:3 Output sign nal 1 16:9 4:3 Pillar-box im 4 mage Shoot and protect 1 14:9 in a 16:9 frrame 4:3 3 Image shoot and protect 14 4:9 in a 4:3 3 frame 14:9 9 Pillar-box ima age in a 16:9 frrame ( (16:9_13) 16:9 Image sho 1 oot and protect 14:9 in a 1 16:9 frame (4 4:3_13) 14 4:9 Letterbox im mage in a 4:3 frrame (16 6:9_11) 16:9 9 Image shoot and protect 14 4:9 in a 16:9 9 frame ( (16:9_14) 16:9 Image sho 1 oot and protect 4:3 in a 1 16:9 fram
GUIDE TO INSTALLATION AND OPERATION 5 Specifications 8VSB/QAM INPUT (IRD-3111-VQ only) Quantity/connector: Tuning range: Input level: One input with F-type connector, 75 ohm 51 MHz-858 MHz -27 dBmV to +33 dBmV QPSK/8PSK INPUT (IRD-3111-DVB-S2 only) Quantity/connector: One input with F-type connector, 75 ohm Demodulation: DVB-S (QPSK) ETSI EN 300 421 DVB-S2 (QPSK/8PSK) ETSI EN 302 307 Tuning range: 940 to 2150 MHz (in 0.
GUIDE TO INSTALLATION AND OPERATION Supported formats: Embedded audio: Return loss: Jitter: SD: 480i59.94, 576i50 HD: SMPTE 274M: 1080i59.94, 1080i50 HD: SMPTE 296M: 720p59.94, 720p50 SMPTE-299M, SMPTE-272M >15 dB up to 1.5 GHz <0.2 UI as per SMPTE-259M-C for SD output <0.
GUIDE TO INSTALLATION AND OPERATION ANNEX 1 – Local Control Panel User Interface IRD-3111 LEV 1 LEV 2 LEV 3 LEV 4 Settings CARD STATUS DEVICE STATUS NO REAR, WRONG REAR, SYS OK (the items in this part of the menu are for information only, and will cycle through the display if the user does not use the control panel buttons) SELECTED INPUT DVB-ASI1, DVB-ASI2*, ETHERNET*, TUNER* TUNER STATUS SIGNAL CHANNEL: FREQ: xxxxMHz MOD: 8-VSB, e.g. BER: X.
GUIDE TO INSTALLATION AND OPERATION and will cycle through the display if the user does not use the control panel buttons) SERVICE TYPE LOAD USER 1 ,USER 2, USER 3, USER 4, USER 5 SAVE USER 1 ,USER 2, USER 3, USER 4, USER 5 INPUT SELECTION ASI/SSI1, ASI/SSI2, ETHERNET, AUTO SELECT AUTO SWITCH DEL. 0, 1, 2, 3,4, 5, … 15 sec USER PRESET INPUT MENU RF MENU SERV SELECT MODE MANUAL, AUTO SERVICE SELECT (PGM xxxxx) CLOCK RECOVERY OFF, FROM PCR SELECT CHANNEL AVAIL.
GUIDE TO INSTALLATION AND OPERATION EMBEDDING AUTO, GENERATION DIALNORM OVERRIDE, PROGRAM 1, PROGRAM 2 GENERATOR PROGRAM 1, PROGRAM 2 ACTIVATION ON, OFF AES 1 Source L1/R1/AC3 1, C1/Lfe1, Ls1/Rs1, L2/R2 AES 2 Source L1/R1/AC3 1, C1/Lfe1, Ls1/Rs1, L2/R2 AES 3 Source L1/R1/AC3 1, C1/Lfe1, Ls1/Rs1, L2/R2 AES 4 Source L1/R1/AC3 1, C1/Lfe1, Ls1/Rs1, L2/R2 AV SYNC QUALITY NORMAL, BEST AV SYNC OFFSET 0, 1, 2, 3, ……, 100 ms AC3 COMPRESSION LINE MODE, RF MODE AC3 DRC OFF, ON ANALOG AUDIO SRC
GUIDE TO INSTALLATION AND OPERATION TEST ALARM MENU OFF, ON NO TS INPUT NO VIDEO SIGNAL NO AUDIO SIGNAL NO REFERENCE REF MISMATCH PROGRAM SYNCHRO TS LIMITS VERSION IRD-31x1: xxxB;xxx SERIAL NUMBER OPTIONS FACTORY DEFAULT ALARM LEVEL OFF, YELLOW, RED, FLASH RED ALARM REPORT NONE, GPI ALARM LEVEL OFF, YELLOW, RED, FLASH RED ALARM REPORT NONE, GPI ALARM LEVEL OFF, YELLOW, RED, FLASH RED ALARM REPORT NONE, GPI ALARM LEVEL OFF, YELLOW, RED, FLASH RED ALARM REPORT NONE, GPI ALARM LEVE
GUIDE TO INSTALLATION AND OPERATION ANNEX 2 – Dolby Metadata Profiles The chart shows the metadata parameter values that are available as Profiles 1 through 4 in the Generator Configuration section of the Metadata / Dolby tab in the Video Output iControl panel. See page 22.
