User Guide ACT-72T Bodypack Transmitter All rights reserved. Do not copy or forward without prior approvals MIPRO. Specifications and design subject to change without notice.
Bodypack Transmitter Bodypack Transmitter Contents 1 Bodypack Controls and Indicators 3 Operating Instructions 4 LCD Display Screen 5 Transmitter Parameters 11 Battery Status 13 Setting MUTE 15 AF Input Connections 16 Battery Removal and Installation Bodypack Controls and Indicators 1 2 3 4 FREQUENCY 5 12 718.275MHz 6 7 8 ON MODE SET 13 9 10 11 1 0 1 Audio Input Connector: TA4F mini 4-pin connector accepts any MIPRO lavalier, instrument and headset microphones and cables.
Bodypack Transmitter 2 MUTE Button: To mute and un-mute the audio signal temporary. 3 Antenna: Flexible 1/4 wave transmitting antenna. 4 Transmitter Housing: Holds PCB board and wires. 5 LCD Panel: Display transmitter parameters. 6 SET Button: Parameter selection button. 7 MODE Button: Allows access to 6 available functions displaying in LCD panel. 8 Power Button: Press and hold 2 seconds to power ON or OFF. 9 ACT IR Port: Align and syncs the transmitter and receiver frequency automatically.
Bodypack Transmitter Bodypack Transmitter LCD Display Screen Transmitter Parameters MODE button ! Press “MODE” button to access one of the six parameters below. FREQUENCY A1 775.275MHz A2 AF MUTE A1 LCD Screen A2 AF (audio) MUTE A3 Transmitter Battery Meter SET button ! A3 Press “SET” button then the changeable functions will twinkle. Change to the desired parameters during the above twinkle by pressing “SET” button. FREQUENCY 775.
Bodypack Transmitter ! Bodypack Transmitter Group & Channel and Frequency are factory preset, thus, its parameter values are displayed after it is ACT synced. Values cannot be changed. GRP CH 01 01 (Group and Channel) FREQUENCY 775.275MHz (Frequency) Setting Input Gain Level ! Selectable AF GAIN between 12dB to -18dB with 6dB parameter up or down selection. ! Press MODE button until AF GAIN mode appears. ! Press SET button once to activate function.
Bodypack Transmitter Bodypack Transmitter Setting RF Output Power MUTE MODE ! 2 RF Output Power Levels: RF-LOW and RF-HI. ! ! Press MODE button until RF POWER mode appears. MUTE MODE: Select from MANUAL and DISABLE. ! Press MODE button until MUTE MODE appears. Press SET button once, the LCD screen starts flashing to denote it is ready to accept mode changes. Press SET button to change between MANUAL and DISABLE in cycle.
Bodypack Transmitter Setting LOCK Bodypack Transmitter Battery Status ! Setting LOCK can be switched to LOCK or UNLOCK mode. ! Press MODE button until SET LOCK mode appears. ! Press SET button to select the desired parameter. ! Press MODE button to confirm and save the change. ! Press SET button twice to remove the LOCK function. ! The LOCK function will be removed automatically when losing power. ! Mute function can still work properly when LOCK.
Bodypack Transmitter ERR Message ! Bodypack Transmitter Setting MUTE When “ERR” appears in the display it indicates that an operational error has occurred. Please refer to the following codes to diagnose which error you are experiencing. ERR no01 EEPROM is not being programmed or internal data error. ERR no02 For testing only. ! Press MUTE button to enter MUTE mode. ! Under MUTE mode, press MUTE button to exit MUTE mode. ! MUTE button is operable when SET LOCK mode is LOCK.
Bodypack Transmitter AF Input Connections External Mute Connector ! Bodypack Transmitter External mute connector is a 3.5mm jack. When an external mute switch cable, MJ-70 (optional) is connected, user can manually mute and unmute the audio temporary.
Bodypack Transmitter Battery Removal and Installation Disassemble the Belt Clip ! Pushing down both snap locks on the sides to open battery compartment cover. Take out the two batteries. (Figure 3) ! Insert two fresh AA batteries (alkaline type is recommended) into the battery compartment according to the correct polarity (- and +) as shown in (Figure 4). Then close the battery compartment cover tightly.
Bodypack Transmitter Bodypack Transmitter & IC - ID Assemble the Belt Clip ! THIS DEVICE COMPLIES WITH PART74 OF THE FCC RULES AND RSS-123 ISSUE 2 OF CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: Turn the bodypack transmitter to the back side. Put the belt clip to the right direction and aim the one side of the belt clip to the slot of the bodypack transmitter like the right diagram. (1) This device may not cause interference.