User Guide ACT-50T Bodypack Transmitters All rights reserved. MN 014/07 Do not copy or forward without prior approvals MIPRO. Specifications and design subject to change without notice.
Bodypack Transmitter Bodypack Transmitter Contents 1 Bodypack Controls and Indicators 3 Operating Instructions 4 LCD Display Screen 5 Transmitter Parameters 12 Battery Status 13 MUTE Control Set-Up 15 AF Input Connections 16 Battery Removal and Installation Bodypack Controls and Indicators 1 2 3 4 GRP 5 6 7 CH 07 03 12 13 8 9 10 11 0 1 Audio Input Connector: TA4F mini 4-pin connector accepts any MIPRO lavalier, instrument and headset microphones and cables.
Bodypack Transmitter 3 Antenna: Flexible 1/4 wave transmitting antenna. 4 Transmitter Housing: Holds PCB board and wires. 5 LCD Panel: Display transmitter parameters. 6 SET Button: Parameter selection button. 7 MODE Button: Allows access to 7 available functions displaying in LCD panel. 8 Power Button: Press and hold 2 seconds to power ON or OFF. 9 ACT IR Port: Align and syncs the transmitter and receiver frequency automatically. 10 Battery Compartment: Holds 2 'AA' batteries.
Bodypack Transmitter Bodypack Transmitter LCD Display Screen Transmitter Parameters MODE button ! GRP 07 03 A1 A2 Press “MODE” button to access one of the 7 parameters below. CH AF MUTE A1 LCD Screen A2 AF (audio) MUTE A3 Transmitter Battery Meter SET button ! A3 Press “SET” button then the changeable functions will twinkle. Change to the desired parameters during the above twinkle by pressing “SET” button.
Bodypack Transmitter ! Bodypack Transmitter Frequency Band, Group & Channel and Frequency are factory pre-set, thus, its parameter values are displayed after it is ACT synced. Values cannot be changed. Setting Input Sensitivity Level BAND 8A GRP ! 4 Selectable Sensitivity Levels: LINE、 MIC-L (MICROPHONE-LOW)、 MIC-M (MICROPHONE- MID)、 MIC-H (MICROPHONE-HIGH). ! Press MODE button until AF GAIN mode appears. (Frequency Band) ! Press SET button once to activate function.
Bodypack Transmitter Bodypack Transmitter Setting RF Output Power MUTE MODE ! 2 RF Output Power Levels: RF-LOW and RF-HI. ! ! Press MODE button until RF POWER LOW or RF POWER HIGH mode appears. MUTE MODE: Select from MANUAL and DISABLE. ! Press MODE button until MUTE MODE appears. Press SET button once, the LCD screen starts flashing to denote it is ready to accept mode changes. Press SET button to change between MANUAL and DISABLE in cycle.
Bodypack Transmitter Bodypack Transmitter ERR Message Setting LOCK ! Setting LOCK can be switched to LOCK or UNLOCK mode. ! Press MODE button until SET LOCK mode appears. ! Press SET button to select the desired parameter. ! Press MODE button to confirm and save the change. ! Press SET button twice to remove the LOCK function. ! The LOCK function will be removed automatically when losing power. ! Mute function can still work properly when LOCK.
Bodypack Transmitter Bodypack Transmitter Battery Status MUTE Control Set-Up Indicates the power remaining in the transmitter battery. When the battery has less than 10% power remaining it must be replaced or recharged. If an under voltage condition continues, the LCD will show “OFF...” and the system will shut down to prevent being overly discharged. MUTE control enables audio to be muted or unmuted temporarily. 100% 80% 60% 40% 20% ! Press MUTE button to mute audio temporarily.
Bodypack Transmitter Bodypack Transmitter AF Input Connections External Mute Connector ! External mute connector is a 3.5mm jack. When an external mute switch cable, MJ-70 (optional) is connected, user can manually mute and un-mute the audio temporary.
Bodypack Transmitter Bodypack Transmitter FCC Battery Removal and Installation Pushing down both snap locks on the sides to open battery compartment cover. Take out the two batteries. (Figure 3) THIS DEVICE COMPLIES WITH PART 74 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) This device may not cause interference. Insert two fresh AA batteries (alkaline type is recommended) into the battery compartment according to the correct polarity (- and +) as shown in (Figure 4).
Bodypack Transmitter Bodypack Transmitter WARNING 1. 2. 3. ! IMPORTANT SAFETY INSTRUCTIONS ! FOR OUTDOOR USE: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. UNDER WET LOCATION: Apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as vases should be placed on the apparatus. 4. Follow all instructions. 5.