User Manual Part 3

ManualsBrandsMipro Electronics ManualsElectronicsTransmitter

FREQ

MODE

SET OFF

SET ON

RF RF

AF AF

BT BT

LOW--CU

MODE

OFF

SET

**NOTE: When program a special frequency via monitoring software;

LCD screen cannot display the number. This is because this special

channel is not in the preset group and channel. Therefore, LCD panel

will look like illustration below.

(1)GR-CH: Displays Information of Group and Channel

B. Operation Guide:

a. Press ''MODE'' and stop on "GR-CH" function, the display showing current group

and channel will be flashing. After 5 seconds, the display will stop flashing.

b. "GR-CH" function is added to display group and channel information. Changing

current group and channel must be done on the receiver.

GR--CH

MODE

"MHz"

A. Operate via MODE Button

(2) FREQ: Displays Information of Transmitter Frequency

A. Operate via MODE Button

B. Operation Guide:

a. Press ''MODE'' and stop on "FREQ" function, the display showing current

frequency will be flashing. After 5 seconds, the display will stop flashing.

B. "FREQ" function is added to display frequency information. Changing current

frequency must be done on the receiver.

**NOTE: To modify transmitter's group, channel and frequency, all

three must be set at the receiver and transmit the new setting to

transmitter via ACT.

(3) LOW-CU: Setup and Change of Low Frequency Cut Off

B. Operation Guide:

A. Operate via MODE Button

a. Press ''MODE'' and stop on "LOW-CU" function, the display showing current state

will be flashing and is ready to be modified.

b. Press ''SET'' button to change to ''ON'' or ''OFF'' as desired.

**NOTE: When the LOW-CU function is ''ON'', the frequency response

below 100Hz will decrease about 4dB with a slope of -6dB/Octave.

DIGITAL WIRELESS BODY PACK TRANSMITTER

Summary of content (4 pages)

PAGE 1
DIGITAL WIRELESS BODY PACK TRANSMITTER DIGITAL WIRELESS BODY PACK TRANSMITTER A. Operate via MODE Button (1)GR-CH: Displays Information of Group and Channel MODE FREQ RF RF B. Operation Guide: BT AF a. BT AF Press ''MODE'' and stop on "FREQ" function, the display showing current frequency will be flashing. After 5 seconds, the display will stop flashing. "FREQ" function is added to display frequency information. Changing current frequency must be done on the receiver. B. 5 A.
PAGE 2
DIGITAL WIRELESS BODY PACK TRANSMITTER DIGITAL WIRELESS BODY PACK TRANSMITTER A. Operate via MODE Button (4) AF-SEN: Setup and Change of Input Sensitivity OFF SET RF RF 10dB MODE RF LIMIT ON SET BT AF BT AF B. Operation Guide: BT AF a. 5 b. A. Operate via MODE Button Press "MODE" and stop on "LIMIT" function, the display showing current state will be flashing and is ready to be modified. Press ''SET'' to change the setting to "ON" or "OFF".
PAGE 3
DIGITAL WIRELESS BODY PACK TRANSMITTER 7. BT: Displays Information of Battery Level DIGITAL WIRELESS BODY PACK TRANSMITTER 4. Cautions 1. BT BT 100% 90% BT BT BT BT 80% 40% 10% 0% 2. When the battery level drops down to 10%, please replace or recharge the battery. If the battery continues to be used at a very lower level, the LCD will display "PO--OFF" and then automatically switch off to avoid over-discharging the battery.
PAGE 4
DIGITAL WIRELESS BODY PACK TRANSMITTER 5. AF Input Connection Methods 6. High Frequency Bypass a. (1) 2-Wire Electret Condenser Microphone Capsule SHIELD AUDIO PIN 1 2 DIGITAL WIRELESS BODY PACK TRANSMITTER b. 4 1 3 2 3 4 When other microphones are in use, some changes may be needed to another microphone before adding it to the system in order to avoid high frequency interference, as illustrated in diagram (1).