User Manual MiVue M760D N594 DVR Driving Recorder
For more information ......................................................................18 Caring for your device ..............................................................18 About GPS ...............................................................................19 Regulatory information .............................................................19 Safety precautions....................................................................21 About the charger ............................................
Precautions and notices • Never attempt to disassemble, repair or make any modifications to your device. Disassembly, modification or any attempt at repair could cause damage to the device and will void any warranty. • If you see or smell smoke from the device, stopping charging immediately. • Keep the device away from the chemical substances or detergents. They could be corrosive and cause damage to the surface of the device.
• Do not expose the wires or connectors to avoid malicious damage. • The installation illustrations are for your reference only. The placement of the components may vary depending on the vehicle model. If you encounter any problems during installation, please contact a skilled installer (for example, the service personnel of the vehicle) for assistance.
GPS multi-function control box ❶ ❹ ❷ ❸ ❶ GPS receiver ❷ Button 1, red indicator ❸ Microphone ❹ Button 2, blue indicator Using a memory card You have to insert a memory card before you can start recording. Your device supports Class 10 memory cards with up to 128 GB capacity. 1. Use a suitable screwdriver. Loosen the 2 screws securing the cover of the memory card slot, and remove the cover. 2. Hold the card (MicroSD) by the edges and gently insert it into the slot as shown in the illustration.
To remove a card, gently push the top edge of the card inwards to release it, and pull it out of the slot. 3. Replace the cover of the memory card slot, and secure it with 2 screws. ✎ • You should use separate MicroSD cards for recording and for regular data storage. • The memory card slot is not hot-swappable. Insert the memory card before powering on your Mio. DO NOT remove the memory card during recording. Turn the device off before removing the memory card.
Installing the cameras Clean the installation surface with rubbing alcohol and make sure that the installation area is free of dust, oil and grease. Secure the camera with the double-sided tape or cable tie. To adjust the angle of the camera lens: ❷ ❶ ❹ ❸ 1. Loosen the screw on the side of the camera holder (❶). 2. You can adjust the camera lens by rotating up and down (❷) and left and right (❸). Adjust the angle of the camera lens by checking the the camera's live view via the MiVue Pro app.
3. Tighten the screw to secure the camera (❹). Caution: When tightening the screw, do not use excessive force (no more than 2 kgf of torque) to avoid damage to the product. Cable connections Caution: Make sure that water will NOT flow down to your Mio's main unit along the cables. You are advised to tape the cables together, cover and secure them inside the motorbike to avoid damage or abnormal sound.
Connecting the main unit and waterproof power cable 1. Check and confirm the vehicle's voltage (12 V) by using the electrical tester as battery voltages varies by vehicle. 2. Choose one of the following connections: • Use the electrical tester to locate the fuse from which the power is not supplied when the vehicle is turned off. Connect the red wire (ACC) to the fuse. Use the electrical tester to locate the fuse from which the power is supplied even when the vehicle is turned off.
❶ ❷ ❸ ❶ Black wire (GND) Connect to the metal part and the negative battery terminal of the vehicle. ❷ Yellow wire (B+) Connect to the fuse from which the power is supplied even when the vehicle is turned off. ❸ Red wire (ACC) Connect to the fuse from which the power is not supplied when the vehicle is turned off. 4. Connect the power cable to the main unit. Arrange and secure the cable to the vehicle. Avoid exposing the long cable. 5.
• During installation, do not damage and keep the connectors dry to avoid short circuits and electric shocks. • For safety purposes, properly secure your Mio and the waterproof power cable to the vehicle. Store the cables properly so that they cannot be pulled or hooked easily. • During installation, do not cause friction and damage to the surface of the wires to avoid fire or short circuits. • The status of the vehicle's battery will affect the voltage value and may cause it to malfunction.
MiVue Pro app The MiVue Pro app allows you to view, share and back up the videos recorded on a MiVue via WIFI. You can also change the settings of your Mio via the MiVue Pro app. Search for "MiVue Pro" in Apple App Store or in Google Play Store to download the app for free. ✎ • The MiVue Pro app is compatible with iOS 9.0 (and above) and Android 5.0 (and above) devices. MiTAC does not guarantee the product's compatibility with smartphones from all manufacturers.
Recording Continuous recording The system will automatically begin continuous recording shortly after start-up. The blue indicator on the GPS multi-function control box will glow, indicating that recording is in progress. ✎ The recording may be divided into several video clips (approximately every minute for each video clip); recording will not stop between video clips. To stop recording, press Button 2 on the GPS multi-function control box.
Event recording You can start an event recording during the continuous recording by pressing Button 1 on the GPS multi-function control box. The blue indicator on the GPS multifunction control box will flash rapidly within every second. Within 15 seconds of the event recording, you can extend the recording for 10 seconds by pressing Button 1 once. The recording can last up to 60 seconds. Event recordings will not be replaced by continuous recordings.
Speed Stamp Displays the driving speed on the recorded video. Date / Time Sets the system date and time. By default, your Mio will acquire correct date and time settings after getting a GPS fix. Distance Unit Sets the preferred distance unit. Format SD Card Formats a memory card. (All data will be erased.) Restore to Defaults Restores the system settings to the factory defaults. MiVue Manager™ MiVue Manager is a tool for you to view the videos recorded on a Mio.
• You can select the file type to display: Event / Normal / Parking. (Your Mio model may not support the "Parking" file type.) • To display all files in the current folder, click All. To return to the calendar view, click Calendar. 3. Double-click the desired file on the file list to start playback. 4. The playback controls are described as follows: ❶ ❷❸ ❹ ❺ ❻ ❼ ❶ Skips to the previous / next file on the list. ❷ Starts or pauses the playback.
6. The tool bar allows you to do the following: ❶ ❷ ❸ ❹ ❺ ❻ ❼ ❽ ❶ Selects the folder that stores the recording files. ❷ Previews and prints the current video image. ❸ Saves the selected files to the specified location on your computer. ❹ Captures and saves the current video image to the specified location on your computer. ❺ Opens the Settings Menu. The Settings items are described as follows: • Change Language: Sets the display language of MiVue Manager.
Resetting your Mio Occasionally, you may need to perform a hardware reset when your Mio stops responding; or appears to be "frozen" or "locked-up." To reset your Mio, press and hold Button 1 and Button 2 on the GPS multi-function control box at the same time for about 5 seconds. 5 sec For more information Caring for your device Taking good care of your device will ensure trouble-free operation and reduce the risk of damage. • Keep your device away from excessive moisture and extreme temperatures.
• Never clean your device with it powered on. Use a soft, lint-free cloth to wipe the exterior of your device. • Never attempt to disassemble, repair or make any modifications to your device. Disassembly, modification or any attempt at repair could cause damage to your device and even bodily injury or property damage and will void any warranty. • Do not store or carry flammable liquids, gases or explosive materials in the same compartment as your device, its parts or accessories.
you are inside a tunnel or building, GPS positioning is not available. Signal reception can be affected by situations such as bad weather or dense overhead obstacles (such as trees, tunnels, viaducts and tall buildings). • The GPS positioning data is for reference only. Regulatory information For regulatory identification purposes, this device is assigned a model number of Products N594.
Declaration of conformity Hereby, MiTAC declares that this N594 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. WEEE This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE – 2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement: This device complies with ISED’s licence-exempt RSSs.
www.mio.