Parts and Instructions Manual SCV 28/32 Rider Scrubber
This manual is furnished with each new MINUTEMAN SCVTM 28/32. This provides the necessary operating and preventive maintenance instructions. Operators must read and understand this manual before operating or servicing this machine. This machine was designed to give you excellent performance and efficiency. For best results and minimal cost, please follow the general guidelines below: · Operate the machine with reasonable care.
Parts and Instruction Manual
Table of Contents Important Safety Instructions ............................................................................................................ 1 For Safety During Operation ........................................................................................................... 1 For Safety When Servicing or Maintaining Machine ........................................................................ 1 Inspection ................................................................................
Scrub Decks ...................................................................................................................................... 14 Cylindrical Scrub Deck .................................................................................................................. 14 Disc Scrub Deck ............................................................................................................................ 15 Scrub Deck Installation .....................................................
Squeegee Mechanism Assembly .................................................................................................. 50 28” Rear Squeegee Assembly ....................................................................................................... 51 28” Rear Squeegee Assembly BOM ............................................................................................. 52 32” Rear Squeegee Assembly .............................................................................................
Important Safety Instructions Operators must read and understand this manual before operating or maintaining this machine. Do not operate this machine in flammable or explosive areas. This machine is designed solely for scrubbing dirt and dust in an indoor environment. Minuteman does not recommend using this machine in any other capacity. The following information below may cause a potential hazard to the operator and equipment. Read this manual carefully and be aware when these conditions can exist.
Inspection Carefully unpack and inspect your SCV Rider Scrubber for shipping damage. Follow unpacking instructions on shipping pallet. Each unit has been tested and thoroughly inspected before shipment. Any damage is the responsibility of the delivery carrier who should be notified immediately. Electrical This machine is battery operated and designed to operate on 36 Volts DC (6) 6-volt batteries. Batteries The recommended batteries are rated 275Ah (Minuteman P.N. 956740).
Machine Overview Front A B C D E F G H I Front Drive Wheel Side Squeegee Accelerator Pedal Steering Tilt Lever Steering Wheel Operator’s Seat Recovery Tank Lid Recovery Tank Control Console Parts and Instruction Manual J K L M N O P Q R Directional Switch Safety Latch Battery Compartment Solution Tank Electrical Panel Rear Squeegee Real Wheel Scrubdeck Roller Bumper Page 3
Machine Overview Rear A B C D E F G H Rear Squeegee Rear Wheel Side Squeegee Accelerator Pedal Solution Tank Steering Tilt Lever Steering Wheel Recovery Tank Lid Parts and Instruction Manual I J K L M N O P Vacuum Filter Access Vac Inlet Assembly Recovery Tank Battery Compartment Clean-Out Cap Recovery Drain Hose Recovery Hose Scrubdeck Page 4
Operator Compartment A B C D E Operator’s Seat Solution Tank Lid Cup Holder Solution Tank Accelerator Pedal Parts and Instruction Manual F G H I Steering Wheel Directional Switch Control Panel Safety Latch Page 5
Control Console For operator ergonomics, the control console houses all the primary function controls in a central area. The key switch and optional headlight and off-aisle wand switches are clustered in the back portion of the console. The directional switch (forward/reverse) is located at the front of the console for easy fingertip operation. The horn button, function selectors, and battery gauge are located in the central part of the console.
Operation Modes 1. Regular Scrub Mode When the machine is running in this mode, the machine will perform all operations. This mode can be used for day-to-day tasks under normal conditions. When the operator sets the directional switch to forward and activates the accelerator pedal, the solution pump will turn on, the brushes will turn on and be lowered to the floor, as well as the rear squeegee.
After double scrubbing, the operator should use the vacuum only mode to recover the dirty solution water from the floor. 4. Vacuum Only Mode When the machine is running in this mode, the machine will only lower the rear squeegee and turn on the vacuum system to recover the dirty solution from the floor. This mode is usually chosen after double scrubbing to recover the dirty solution but it can also be used to pick up spills.
Fault / Diagnostic Codes When an error or fault occurs within the machine, a fault code will appear on the battery gauge represented by a specific number of flashing LEDs. The figure below shows a listing of the different codes.
Empty Solution Tank Indicator Once the solution tank has become empty, the battery gauge will blink a solid 9 LEDs at a constant interval to alert the operator that the solution tank needs to be filled. Low Battery Indicator If the battery life is low, the battery gauge bar icon will be flashing to inform the operator that the machine is almost out of power. Once this signal is displayed, all functions will shut off, including transport mode.
Operation of Controls Steering Wheel The steering wheel is adjustable for operator comfort by pulling the tiltsteering lever up and positioning the steering wheel up or down (there are three possible positions). Pulling on the tilt-steering lever and positioning the steering column in an upright position provides the operator with more room when climbing up and down the machine. Accelerator Pedal Located on the right side of the operator compartment on the floor is the accelerator pedal.
Emergency Disconnect Button This button is located in the middle of the electrical panel that is directly underneath the operator’s seat. When the red emergency button is pressed, power will be turned off. Use this button in case of a machine emergency. The red knob needs to be raised in order to run the machine. To reactivate, turn the knob as shown by the arrows on the switch and the button will pop up. All operational settings are retained even when the power is turned off and on.
Battery Connection Diagram Batteries Installed with Spacers Parts and Instruction Manual Page 13
Scrub Decks Minuteman offers two deck types (Cylindrical and Disc) to fit your specific needs. The SCV design is very dynamic wherein the decks are interchangeable in a matter of minutes whenever necessary (removal of four bolts, one hose, and one electrical connection). The cylindrical brush deck has five built-in spray jets to uniformly dispense cleaning solution on the floor and a wet sweeping debris tray to collect loose objects on the floor.
Disc Scrub Deck A B C D E F G Center Deck Cover Side Deck Cover (2) Brush Motor Mounting Plate Solution Feed Hose Power Connector Three Sided Knob (4) Parts and Instruction Manual H I J K L M Bolt (4) Helical Lock Washer (4) Flat Washer (4) Wing Nut for Squeegee Adj. (4) Helical Lock Washer for Squeegee Adj. (4) Flat Washer for Squeegee Adj.
Scrub Deck Installation When installing a cylindrical deck to a machine: 1. Install brushes after the deck has been mounted to avoid flat spots on the brushes. 2. Use a piece of cardboard underneath the deck to prevent scratches to the painted surface when sliding the deck under the machine. 3. Make sure the scrub deck is oriented correctly with the spray jets towards the front of the machine. hen installing a disc scrub deck to a machine: 1.
d. Align the notches on the brush with the drive pins on the hub. e. Push the brush all the way in until it bottoms out. f. Insert the access door hub into the other end of the brush. g. Reinstall the wing nuts and yellow 3 sided knobs and tighten. Important Note when Interchanging Scrub Decks As previously mentioned, the scrub deck brush pressure is computer controlled.
Side Squeegees The side squeegees (left and right) are attached to the scrub decks. These items channel the dirty solution to the rear squeegee, helping contain the water within the machine’s cleaning path. These squeegees are raised when the scrub deck is in the raised position. The side squeegees are pre-adjusted at the factory. Adjustments may be required when replacing worn blades or to achieve optimum performance for different floors and conditions.
Cylindrical Deck Side Squeegee Components A B C D Side Squeegee Blade Black Squeegee Adjustment Knob (2) Yellow Brush Access Knob Side Squeegee Hinge Brush Changes On the Cylindrical Deck In order to change the brushes on the cylindrical deck the side squeegee must be moved in order to access the brush doors. The cylindrical deck was designed so one can change the brushes without having to realign the side squeegees.
Rear Squeegee The rear squeegee is the main element that acts as the conduit that transfers the spent solution into the recovery tank. A daily maintenance check of this component is essential to have optimum machine performance. The rear squeegee assembly is equipped with a universal front blade that allows the operator the option to use a slotted and a non-slotted side for specific applications. Each blade configuration has two usable edges. The rear blade however has four usable edges.
Rear Squeegee Adjustment Ensure that the scrubber is on a relatively flat surface. Turn on the key switch and select the Vacuum only mode. This lowers the squeegee to the floor and turns the vacuum motor on. Move the scrubber one or two feet forward slowly while someone behind the machine checks the rear squeegee blade (item A) for uniform deflection to the floor. If uneven deflection or lay is evident, minor adjustments may be necessary to avoid streaking and uneven wear on the blade.
The SCV Rider This machine was designed with total operator comfort and ease of use in mind. All machine components have been designed as a total system to efficiently clean dirty floors. The SCV has four available scrub head types and sizes to fit specific applications. Please contact your Minuteman representative for specific recommendations for the correct scrub head type, size, and brush type and chemical applications.
Machine Operation Follow the instructions in preparing the machine for use as described in this manual. 1. While seated on the machine, adjust the steering wheel to desired position using the tilt lever. 2. Turn the Key switch ON (I). The Battery Gauge will light up and display the Remaining Battery Life. 3. Select one of the five available Modes on the Control Console for the required task. Refer to the Operation Modes section of this manual for a complete description of the functions. 4.
1. To stop scrubbing, select the Transport mode. This will automatically stop the Solution Flow, raise the Scrub deck, and raise the Rear squeegee (there is a 15 second delay for the vacuum motor). 2. Drive the SCV to a designated dirty water disposal area and empty the Recovery tank. To empty, remove the Drain hose from its storage hanger. Unscrew the plug and hold the hose end above the water level in the tank to avoid sudden, uncontrolled flow of dirty water.
Maintenance Schedule Daily Charge Batteries Weekly Check Each Battery Cell(s) Water Level Check/Clean Tanks & Hoses Check/Clean/Rotate the Brushes/Pads Check/Clean the Squeegee Inspect Scrub Housing Skirts Inspect and Clean Solution Filter Check Foot/Parking Brake for Wear & Adjustment Clean Spray jets on Cylindrical System Check/Clean Vacuum Shut-Off Float Check/Clean the Vacuum Motor Foam Filter Clean Hopper on Cylindrical System Monthly Lubrication – Grease Fittings, chains, etc.
General Machine Troubleshooting Problem Poor water pick-up Possible Cause Worn or torn squeegee blades Squeegee out of adjustment Recovery tank full Recovery tank drain hose leak Recovery tank lid gasket leak Debris caught in squeegee Vacuum hose clogged Using too much solution Poor scrubbing performance Inadequate solution flow or no solution to the floor Vacuum hose to squeegee or recovery tank disconnected to squeegee or damaged Worn brushes Wrong brush or cleaning chemical Debris caught on scrub bru
No FWD/REV drive Drive system speed controller. Emergency stop switch tripped Recovery tank full Excessive foaming in recovery tank. Check error fault codes (See page 15) Reset machine: Turn key switch off and restart. Activate switch by turning as indicated by arrows. Empty recovery tank Empty recovery tank. Use less or change chemical. Vacuum motor does not turn on Five LEDs flashing on Battery Gauge Use defoaming agent. Check for motor overload.
Exploded Views Main Assembly I Parts and Instruction Manual Page 28
Main Assembly I BOM ITEM 1 2 3 4 5 6 7 8 9 9A 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART NO.
Main Assembly II Parts and Instruction Manual Page 30
Main Assembly II BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 PART NO.
ITEM 1 2 3 4 5 6 7 8 9 PART NO. 281101 281468 281469 281470 711242 711515 711546 281201E 282301E BILL OF MATERIAL REQ'D DESCRIPTION 1 MAINFRAME WMT, 28" SCRUBBER 1 FRICTION STRIP 9.50" 1 FRICTION STRIP 14.25" 1 FRICTION STRIP 18.00" 4 BLT-HEX 3/8 -16X1.00 ZP 4 WSR-FLAT .406 X .812 X .
Mainframe Assembly II Parts and Instruction Manual Page 33
Mainframe Assembly II BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 PART NO.
Front Drive Assembly Parts and Instruction Manual Page 35
Front Drive Assembly BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 PART NO. 281054 281057 281252 281254 281260 281267 281268 281276 281279 281282 383074 383075 383076 383077 383078 383250 383277 383364 430051 710858 710991 711352 711524 711546 711588 711594 711713 711807 712113 713043 740099 744016-1 748010 748010-3 748049 748122 809148 809247 Parts and Instruction Manual BILL OF MATERIAL - 281251 REQ'D DESCRIPTION 1 CHAIN, STEERING No.
Steering Assembly Parts and Instruction Manual Page 37
Steering Assembly BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PART NO. 66-138-A 70-516-16 363-816 281047 281328 281331 281484 281989 282302 282303 282309 282310 383098 383152 383277 430051 710153 711374 711380 711506 711521 712102 712301 712310 748013-1 809148 340742MCH 712099PLT Parts and Instruction Manual BILL OF REQ'D 2 4 1 1 1 1 1 1 1 1 1 2 1 1 4 1 4 4 2 4 2 1 2 1 1 5 4 2 MATERIAL - 282301E DESCRIPTION BEARING, 3/4" BLT-CAR 5/16-18 X 1.
Solution Tank Assembly / Seat Assembly Parts and Instruction Manual Page 39
Solution Tank Assembly / Seat Assembly BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 BILL OF MATERIAL - 281012E, 281365 PART NO.
Electrical Panel ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO. 281402 281412 281910 281982 710202 710380 711206 711372 711501 711502 711505 711541 711544 711599 712822 742350 742748 748012 748014 748015 748032 748152 748153 748174 281449 806006 830557 Parts and Instruction Manual REQ'D 1 1 1 1 1 10 2 6 1 4 12 1 12 3 3 1 1 1 1 1 1 1 1 1 2 3' 11.
Console Assembly ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 281005 281372 281373 281375 281499 710204 711161 711301 711541 712320 715455 742927 747011-1 747020 747025 747027 748047 748151 748154 809874 281378S P 281497S P Parts and Instruction Manual BILL OF M ATERIAL REQ'D DES CRIP TION 1 SCV 28/32 CONSOLE 1 GASK ET - IGNITION SW ITCH PANE L 1 GASK ET - M EM BRA NE SW ITCH 1 GASK ET - DIRECTION SW ITCH 1 BKT, CONTROLS, SCV 2832 2 SCR-M C 6-32 X .
Recovery Tank Assembly I Parts and Instruction Manual Page 43
Recovery Tank Assembly I BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 BILL OF MATERIAL - 281010E PART NO. REQ'D DESCRIPTION 70-516-16 2 BLT-CAR 5/16-18 X 1.00 241060 1 SCREENED FLOAT 241433 1 RECOVERY TANK SAFETY STRAP, SCV 24/26 260203 1 WIRE GRIP HOSE CLAMP 260579 1 TOOL CLIP, 1.5" HOSE 281006 1 LID - FIXED 2800 RECOVERY TANK 281007 1 LID-MOVABLE 2800 RECOVERY TANK 281018 1 GASKET, NEO 6.00 X 4.
Recovery Tank Assembly II ITEM 1 2 3 4 5 6 7 8 9 BILL OF MATERIAL - 281010E PART NO. REQ'D DESCRIPTION 281019 1 DEFLECTOR 281490 1 VAC INLET WMT, SCV2832 281951 1 VAC INLET GASKET 450221 1 Q.C. COUPLING (FEMALE) 450223 1 FITTING BRASS 1/8 FPT - 1/8 BARB 711161 4 SCR-HI/LO 10 X 3/4 STL BLK ZINC 711515 2 WSR-FLAT .406 X .812 X .
Battery Box Assembly BILL OF MATERIAL - 281014 ITEM PART NO. REQ'D DESCRIPTION 1 281004 1 BATTERY TRAY - 2800 2 281059 1 BATTERY BOX STIFFENER WM'T 3 281671 2 BRACKET, U CHANNEL SPACER 4 281672 2 BKT, BATTERY STOP, SCV2832 5 711229 9 BLT-HH 5/16-18 x .875 6 711374 9 NUT-NYLOC 5/16-18 7 711507 9 WSR-FLAT .37 X 1.12 X .
Pump Assembly Parts and Instruction Manual Page 47
Pump Assembly BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART NO.
BILL OF MATERIAL - 281201E ITEM PART NO. REQ'D DESCRIPTION 1 380-632-20 2 3/16 COTTER PIN 2 281202 1 REAR AXLE WMT 3 281210 2 REAR WHEEL ASSY 4 281213 4 RING & BUSHING ISOLATOR 5 281460 2 AXLE CASTING, REAR - SCV 28/32E 6 383194 4 BEARING CONE 7 711169 8 SCR-1/2-20 X 1.25 SOCKET FH W/ PATCH 8 711450 2 NUT-SLOTTED, 1-14 UNS 9 711514 2 WSR-FT 1.0 ID X 2.
Squeegee Mechanism Assembly ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO.
28” Rear Squeegee Assembly Parts and Instruction Manual Page 51
28” Rear Squeegee Assembly BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO. 241721 241745 281074 281075 281732 281734 281736 281738 281740 281763 281764 430325 710530 711026 711367 711507 711515 711546 711550 711560 711563 712091 808829 832015 Parts and Instruction Manual BILL REQ'D 1 2 1 1 1 1 1 1 1 1 1 2 7 5 2 6 2 2 4 2 2 2 2 2 OF MATERIAL - 241740 DESCRIPTION SQUEEGEE WMT ASS'Y, SCV 24/26 WING BOLT 3/8-16 X 1.
32” Rear Squeegee Assembly Parts and Instruction Manual Page 53
32” Rear Squeegee Assembly BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PART NO. 241743 241745 281074 281075 281740 281781 281782 281783 281784 281785 281786 430325 710530 711026 711367 711507 711515 711546 712091 808829 832015 Parts and Instruction Manual REQ'D 1 2 1 1 1 1 1 1 1 1 1 2 7 5 2 6 2 2 2 2 2 BILL OF MATERIAL DESCRIPTION SQUEEGEE WMT ASSY, 32" WING BOLT 3/8-16 X 1.
Squeegee Lift Mechanism BILL OF MATERIAL ITEM PART NO. REQ'D DESCRIPTION 1 241057 1 KNOB,3/8-16 X 1-3/4 FOUR PRONG. 2 241751-1 1 REAR SQUEEGEE MOUNT PLATE WMNT, SCV 24/26 3 711367 2 NUT- WING 3/8-16 ST PL 4 711506 2 WSR-FLT .344 X .690 X .062 STL ZINC 5 711524 1 WSR-WAVE .52 X .87 X .01 6 711569 1 WSR-FLT .390 X .880 X .062 NYL 7 711671 1 CLEVIS PIN .31X2.13 11-10 8 711713 1 RETAINING RING - "E" TYPE EXT .
28” Cylindrical Scrub Deck Parts and Instruction Manual Page 56
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PART NO. REQ'D 210118 4 241544 1 241546 1 281023 2 281036 2 281038 1 281040 3 281041 5 281053 2 281058 2 281519 2 281544 2 281548 2 281550 2 281557 1 281558 1 281598 8 281606 1 281675 2 281676 2 281681 2 281684 2 281851 1 281857 1 281866 2 281868 1 281869 1 281832 1 281901 1 320264 1 361252 2 383551 2 383558 4 430051 2 450122 2 BILL OF MATERIAL DESCRIPTION ITEM PART NO.
32” Cylindrical Scrub Deck Parts and Instruction Manual Page 58
ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PART NO. 210118 241544 241546 281023 281036 281038 281040 281041 281053 281058 281519 281544 281548 281550 281557 281558 281598 281606 281675 281676 281681 281684 281851 281857 281866 281868 281869 281892 281906 320264 361252 383551 383558 430051 450122 REQ'D 4 1 1 2 2 1 3 5 2 2 2 2 2 2 1 1 8 1 2 2 2 2 1 1 2 1 1 1 1 1 2 2 4 2 2 BILL OF MATERIAL DESCRIPTION ITEM PART NO.
28” Disc Scrub Deck Parts and Instruction Manual Page 60
28” Disc Scrub Deck BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PART NO.
32” Disc Scrub Deck Parts and Instruction Manual Page 62
32” Disc Scrub Deck BOM ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PART NO.
Cylindrical Scrub Deck Side Squeegee (Left Hand Side) ITEM 1 2 3 4 5 6 7 PART NO. 241679 281855 281856 281859 281860 710154 711622 Parts and Instruction Manual BILL OF MATERIAL - 281851 REQ'D DESCRIPTION 1 LONG RETAINER, SIDE SQ SCV2426 1 BACKER BLADE, LONG SCV 2832 1 SHORT RETAINER, SIDE SQ SCV2426 1 SIDE SQUEEGEE BLADE LINATEX, SCV 2832 1 DISK SQUEGEE BRKT WMT LH,SCV 28/32 6 SCR-MC TR HD 10-32 X .
Cylindrical Scrub Deck Side Squeegee (Right Hand Side) ITEM 1 2 3 4 5 6 7 PART NO. 241679 281855 281856 281859 281864 710154 711622 Parts and Instruction Manual BILL OF MATERIAL - 281857 REQ'D DESCRIPTION 1 LONG RETAINER, SIDE SQ SCV2426 1 BACKER BLADE, LONG SCV 2832 1 SHORT RETAINER, SIDE SQ SCV2426 1 SIDE SQUEEGEE BLADE LINATEX, SCV 2832 1 SQUEEGEE BRK'T WMNT RH, SCV 28/32 6 SCR-MC TR HD 10-32 X .
Disc Scrub Deck Side Squeegee (Left Hand Side) ITEM 1 2 3 4 5 6 7 PART NO. 241679 281855 281856 281859 281880 710154 711622 Parts and Instruction Manual BILL OF MATERIAL - 281878 REQ'D DESCRIPTION 1 LONG RETAINER, SIDE SQ SCV2426 1 BACKER BLADE, LONG SCV 2832 1 SHORT RETAINER, SIDE SQ SCV2426 1 SIDE SQUEEGEE BLADE LINATEX, SCV 2832 1 DISK SQUEGEE BRKT WMT LH,SCV2426 6 SCR-MC TR HD 10-32 X .
Disc Scrub Deck Side Squeegee (Right Hand Side) ITEM 1 2 3 4 5 6 7 PART NO. 241679 281855 281856 281859 281877 710154 711622 Parts and Instruction Manual BILL OF MATERIAL - 281875 REQ'D DESCRIPTION 1 LONG RETAINER, SIDE SQ SCV2426 1 BACKER BLADE, LONG SCV 2832 1 SHORT RETAINER, SIDE SQ SCV2426 1 SIDE SQUEEGEE BLADE LINATEX, SCV 2832 1 SQUEEGEE BRK'T WMNT RH, SCV 2426 6 SCR-MC TR HD 10-32 X .
Cylindrical Scrub Deck and Roller Bumper Mounting Parts and Instruction Manual Page 68
SCV28CQP & SCV32CQP BOM’s ITEM 1 2 2A 2B 2C 2D 2E 2F 3 4 5 6 7 8 9 10 ITEM 1 2 2A 2B 2C 2D 2E 2F 3 4 4A 5 6 7 8 9 10 PART NO. 66-436-A 281520 281521 281522 281525 281526 281527 281529 281831 281955 360017 711242 711515 711546 713042 3400661 BILL OF MATERIAL - SCV28CQP REQ'D DESCRIPTION 2 RUBBER ROLLER 2 BRUSH, CYL 28" .022 NYLON 2 BRUSH, CYL 28" .028 NYL 2 BRUSH, CYL 28" .
Disc Scrub Deck and Roller Bumper Mounting Parts and Instruction Manual Page 70
SCV28DQP & SCV32DQP BOM’s ITEM 1 2 3 4 5 6 7 8 9 9A 9B 9C 9D 9E 9F 10 PART NO. 66-436-A 281870 281955 360017 711242 711515 711546 713042 3313135 3313125 3313127 3313131 3313133 3315494 3315386 3400661 BILL REQ'D 2 1 1 2 10 13 14 4 2 2 2 2 2 2 2 2 OF MATERIAL - SCV28DQP DESCRIPTION RUBBER ROLLER DISK SCRUBDECK ASSEMBLY, 28" NO BRUSHES FRONT ROLLER MOUNT BRKT WMT 3/4" X 4.50 CLEVIS PIN BLT-HEX 3/8 -16X1.00 ZP WSR-FLAT .406 X .812 X .
Plumbing Diagram Parts and Instruction Manual Page 72
Wiring Diagrams TRIO Connections Parts and Instruction Manual Page 73
P3 TRIO Connections Parts and Instruction Manual Page 74
P2 TRIO Connections 75 Parts and Instruction Manual Page 75
Wire Colors / Codes Parts and Instruction Manual Page 76
Minuteman International Made Simple Commercial Limited Warranty Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in workmanship and materials under normal use. Minuteman will, at its option, repair or replace without charge, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals.
