Installation Instructions
S2 Remote Control Switch
• MR40Z •
Configuration Parameter:
Our Products warrants this product to be free from manufacturing defects for a period
of one year from the original date of consumer purchase. This warranty is limited to the
repair or replacement of this product only and does not extend to consequential or
incidental damage to other products that may be used with this product. This warranty
is in lieu of all other warranties, expressed or implied. Some states do not allow
limitations on how long an implied warranty lasts or permit the exclusion or limitation
of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary
from state to state.
Warranty
Scene Control:
This remote supports four scene controls
Spec：
Battery: CR2032*1
Frequency: 908.42MHz
Temperature Range: 32°F~104°F
Indoor use in dry location
S2 Remote Control Switch features：
Z-wave Control
Inclusion/Exclusion Function：
To remove the device
To add the device
Wake up the Device:
Factory reset
Parameter 1 Battery report threshold %
Use it to set battery level for battery reports.
size=1 byte Available range : 1-20
(DEFAULT): 10%
Parameter 2 Low Battery alarm report
Use it to set battery level for low battery reports.
size=1 byte Available range : 5%-20%
(DEFAULT) : 5%
Parameter 4 LED Indicator Color for Second button remote control (Scene 2 activation)
Choose the LED indicator color for Second button remote control triggers
size=1 byte Available settings: 0--6
Value=0 White
Value=1 Purple
Value=2 Orange
Value=3 Cyan
Value=4 Red
Value=5 Green
Value=6 Blue
(DEFAULT) : 1
Parameter 5 LED Indicator Color for Third button remote control (Scene 3 activation)
Choose the LED indicator color for Thrid button remote control triggers
size=1 byte Available settings: 0--6
Value=0 White
Value=1 Purple
Value=2 Orange
Value=3 Cyan
Value=4 Red
Value=5 Green
Value=6 Blue
(DEFAULT) : 2
Parameter 6 LED Indicator Color for Fourth button remote control (Scene 4 activation)
Choose the LED indicator color for Fourth button remote control triggers
size=1 byte Available settings: 0--6
Value=0 White
Value=1 Purple
Value=2 Orange
Value=3 Cyan
Value=4 Red
Value=5 Green
Value=6 Blue
(DEFAULT) : 3
Parameter 7 LED Indicator Brightness
Choose the LED indicator Brightness level
size=1 byte Available settings: 0--10
Value=0 LED off
Value=1 10% Brightness
Value=2 20% Brightness
Value=3 30% Brightness
Value=4 40% Brightness
Value=5 50% Brightness
Value=6 60% Brightness
Value=7 70% Brightness
Value=8 80% Brightness
Value=9 90% Brightness
Value=10 100% Brightness
(DEFAULT) : 5
Parameter 3 LED Indicator Color for First button remote control (Scene 1 activation)
Choose the LED indicator color for First button remote control triggers
size=1 byte Available settings: 0--6
Value=0 White
Value=1 Purple
Value=2 Orange
Value=3 Cyan
Value=4 Red
Value=5 Green
Value=6 Blue
(DEFAULT) : 0
1. Follow the instructions for your Z-Wave certified controller to adding device
from the Z-Wave network.
2. Once the controller is preparing to add your device, press the FIRST BUTTON(ONLY)
5 times, LED flashing in blue during inclusion and LED stays on green for 2 seconds
after inclusion successfully. If LED flashing purple for 3 seconds, please reset the
device. LED will stay on red for 2 seconds after inclusion failed.
1. Follow the instructions for your Z-Wave certified controller to remove a device
from the Z-Wave network.
2. Once the controller is preparing to remove your device, press the SECOND
BUTTON(ONLY) 5 times, LED flashing in purple during exclusion and the LED stays on
green for 2 seconds after exclusion successfully. LED will stay red for 2 seconds after
exclusion failed.
Press the THIRD buttom 5 times quickly, LED will stay solid on blue when awake and
will turn off when device goes back to sleep mode.
Manual: Press the Fourth button 5 times, LED flashing red 5S while press 5 times again,
LED will stays red for 2 seconds then off.
Scene 1 : First Button 1-Tap/2-Tap/3-Tap/Held/Released
Scene 2 : Second Button 1-Tap/2-Tap/3-Tap/Held/Released
Scene 3 : Third Button 1-Tap/2-Tap/3-Tap/Held/Released
Scene 4 : Fourth Button 1-Tap/2-Tap/3-Tap/Held/Released
Association Group:
This remote supports 9 Association Group controls
Support group number: 9
Each group max. Support 10 devices
Group 1 Lifeline
Group 2 First button press 1x send basic set 0xff, Second button press 1x send basic
set 0x00.
Group 3 Third button press 1x send basic set 0xff, Fourth button press 1x send basic
set 0x00
Group 4
First button hold more than 0.5s send SWITCH_MULTI-
LEVEL_START_LEVEL_CHANGE(Dim Up)
First button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE
Second button hold more than 0.5s send SWITCH_MULTI-
LEVEL_START_LEVEL_CHANGE(Dim Down)
Second button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE
Group 5
Third button hold more than 0.5s send SWITCH_MULTI-
LEVEL_START_LEVEL_CHANGE(Dim Up)
Third button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE
Fourth button hold more than 0.5s send SWITCH_MULTI-
LEVEL_START_LEVEL_CHANGE(Dim Down)
Fourth button release send SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE
Group 6 First button press 1x to toggle on/off (send basic set 0xff or 0x00).
Group 7 Second button press 1x to toggle on/off (send basic set 0xff or 0x00).
Group 8 Third button press 1x to toggle on/off (send basic set 0xff or 0x00).
Group 9 Fourth button press 1x to toggle on/off (send basic set 0xff or 0x00).
Command Class
Generic Device Class: 0x07-GENERIC_TYPE_SENSOR_NOTIFICATION
Specific Device Class: 0x01-SPECIFIC_TYPE_NOTIFICATION_SENSOR
Command Classes:
0x5E-COMMAND_CLASS_ZWAVEPLUS_INFO
0x85-COMMAND_CLASS_ASSOCIATION
0x8E-COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
0x59-COMMAND_CLASS_ASSOCIATION_GRP_INFO
0x31-COMMAND_CLASS_SENSOR_MULTILEVEL
0x55-COMMAND_CLASS_TRANSPORT_SERVICE
0x86-COMMAND_CLASS_VERSION
0x72-COMMAND_CLASS_MANUFACTURER_SPECIFIC
0x5A-COMMAND_CLASS_DEVICE_RESET_LOCALLY
0x73-COMMAND_CLASS_POWERLEVEL
0x80-COMMAND_CLASS_BATTERY
0x9F-COMMAND_CLASS_SECURITY_2
0x71-COMMAND_CLASS_NOTIFICATION
0x87-COMMAND_CLASS_INDICATOR
0x30-COMMAND_CLASS_SENSOR_BINARY
0x70-COMMAND_CLASS_CONFIGURATION
0x84-COMMAND_CLASS_WAKE_UP
0x6C-COMMAND_CLASS_SUPERVISION
0x7A-COMMAND_CLASS_FIRMWARE_UPDATE_MD
This device complies with part 15 of the FCC and Industry Canada license-exempt RSS standard(s).
Operation is subjected to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
To comply with the FCC RF exposure compliance requirements, no change to
the antenna or the device is permitted. Any change to the antenna or the device could result in the
device exceeding the RF exposure requirements and void user’s authority to operate the device.
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
FCC / IC
FCC NOTE:
NOTE:
Important note:
Please contact us if you have any questions:
ask@minoston.com
www.minoston.com
Note:
Install the custom device handler to access the right functions
if you’re using the SmartThings hub. Please visit our website:
www.minoston.com or email us: ask@minoston.com.
1.Please read this the online guidels at support Minosto.com/Z-wave remote carefully
2.Do not use it in location with direct water contact.
3.Contains small parts keep away from children.
1.Use by hand open the remote cap,and push in to separate the 2 halves
2.Remove the battery tabs
3.Your Z-wave remove Immediately should flash LED to indicate it is powered.
1.Power by battery,no need wires needed.Note the ± direction of the battery
2.Control other Z-wave devices and enable scenes with a click of a button
3.The device with S2 and SmartStart support
Program button:
Battery：CR2032*1
Mounting plate
Face plate
Magets
Hang wallplate
Press 5x: Add Z-Wave Network
Press 5x: Remove Z-Wave Network
Press 5x: Wake-up Device
Reset :Press 5x while hold 5s,then press 5x again
Battery position
Note:DSK Code can be foucd on packaging.
Do not remove or damage them.
Open and access the battery
Choose your hub into and scan the QR code with your phone's camera and
add to Smartstar
Adding Device To your hub and Z-Wave Network for QR code
Screws x2
Screws x2
RGB LED Indicator:
Inclusion: flashing blue
Exclusion: flashing purple
Wake up :stay solid blue
Reset :flashing red
SIZE: 220 x 280 mm
材质：80G 书写纸
拆法：风琴页 55 x 70 mm 成品
正面
背面
背面
Power the device