©2017 Minks Lighting, Inc. Manual design and all Clements of manual design are protected by United States Federal and/or State Law including Patent. Trademark and/or Copyright Laws.
The Minka-Aire® warranty is for from the date of purchase from an authorized Minka-Aire® Lifetime — dealer This warranty is only valid to the original purchaser or user against all defects in material and workmanship {light bulbs excluded] for one {1} full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minks Aire® ceiling fan {excluding wall controls and electrical components), to the original purchaser or user.
Warranty Service Information To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty claim. Replacement is subject to availability of the same model.
SAFETY RULES— — 1 PACKAGE CONTENTS INSTALLING THE FAN HANGING THE FAN ELECTRICAL CONNECTIONS 5 FINISHING THE INSTALLATION ———6 Y ‘Gaffe ui @. 5h millionaire, 1151 W. Bradford Court.
1 SAFETY RULES 1. Before you begin installing the fan, shut power off the circuit breaker of the fuse box 2 Be cautious] Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams 3. Make sure that all electrical connections comply with local codes, ordinance, or National Electrical Codes. Hire a qualified electrician or consult a do-it your self wiring handbook iF you are unfamiliar with installing electrical wiring 4.
ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a limiting device If laming exceeds 75 watts, the ceiling Fan light kit will shut off automatically NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care are factors which can not be built into this product.
2 PACKAGE CONTENTS Unpack your fan and check the contents. You should have the fol lowing items: 1. Hanger bracket {Hanger bracket A. Mounting hardware: support included 10%1x 1.5" Woody screws{2 pes} 2 Canopy 32d5D19 Imm Washer (2 pes) 3. Canopy cover 84-32 box screws (2 pes} 4 Standard down rod assembly (61 Spring washers (2 pes) 5 Coupling cover 8% Star washers (2 pes} 6. Fan motors housing Wire aunts (3 pes) 7 LED Light Kit B. UAXU2Z +5 Motor screws £9 pest 8B.
Tools Required: Philips screw driver. slotted screw driver. step-ladder, wire cutters, electrical tape MOUNTING OPTIONS If there isn't an existing mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers Secure the outlet box directly to the building structure. Use appropriate Fasteners and building materials.
4 HANGING THE FAN WARNING: All of the parts, hardware and components such as the hanger bracket and hanger bal! have been provided for your safety and the proper Installation of your new selling fan. The use of other parts, hardware or components not supplied by Minks Aire® with the fan will cold the Minks Alrs® Warranty. REMEMBER to tum off the power. Follow the steps blow te hang your fan properly: Step 1.
5 ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or breaker box before wiring NOTE: The Ire Contre!® System for this DC motor fans is equipped with a learning frequency function which has 32 code combinations to prevent potential interference from other remote units. The frequency on your Receiver and Transmitter units have been preset at the factory. {Fig. 10) No frequency change is necessary.
Step 1 Motor to House Supply Wires Electrical Connections: Connect the WHITE wire {Neutral} from the outlet box to the WHITE wire marked ‘AC in N' from the motor. Connect the BLACK wire (Hot) from the outlet box to the BLACK wire marked ‘AC in L' from the motor. Secure all wire connections with the plastic wire nuts provided. (Fig. 11} Step 2. if your outlet box has a GROUND Walgreen or Bare Copper) connect this wire to the Hanger Ball and Hanger Bracket Ground wires.
6 FINISHING THE INSTALLATION Step 1. Remove 1 of the 2 screws from the bottom of the hanger bracket and loosen the other one half a turn from the screw head Step 2. Slide the canopy up towards the hunger bracket and place the key hole on the canopy over the screw on the hanger bracket turn canopy until it locks in place at the narrow section of the key holes. (Fig. 12} Step 3.
ATTACHING THE FAN BLADE Notice THIS SIDE UP" label on fan blades The blade are not reversible {Fig.
8 INSTALLING THE LED LIGHT KIT Raise the cap and secure it to the fan by turning the cover clockwise until snug DO NOT OVER TIGHTEN. (Fig.
OPERATING THE REMOTE CONTROL/WALL CONTROL Remote Control only: Install a A23 12 volt battery include. To prevent damage to transmitter remove the battery if not used for long periods of time. Your DC brush less motor is equipped with a self B.
Note: The aura learning function will only mandate within 60 seconds when turning the fan's AC power ON 1. Select desired frequency from the back of transmitter. 2 Press the transmitter's "OFf’ button, and hold the "Off" button for over 10 seconds. Once the receiver has detected the frequency.
Speed settings for warm or cold weather depend on factors such as room size, ceiling height and number of Fans NOTE: ko change the direction of the rotation of the blades the fan must be in operation mode Warm Weather {forward} A DOWNWARD airflow creates a cooling effect as shown in Figure 17. This allows you te set your ais conditioner warmer setting without affecting your comfort.
10 CARBURETOR FAN Here are some suggestions to help maintain your fan 1. Because of the fan's natural movement some connections may become loose. Check the support connections, brackets and blade attachments twice a year. Make sure they are secure. {lt snot necessary to remove fan from the ceiling} 2 Clean your fan periodically to help maintain its new appearance over the year.
TROUBLESHOOTING 11 SYMPTOM SYMPTOM Fan will not start Fan Sounds Noisy SOLUTION SOLUTION # Check to make sure the wall switch is turned on e Allow a 24 hour break in" period Most noises associated » Check circuit fuses or breakers with a new fan will go away during this time. Make sure the * Caution! Make sure the power is turned off before performing the screws that attach the fan blade holder to the motorbikes following steps.
SYMPTOM Fan Wobble SOLUTION ® Mote: All blade sets are grouped by weight. Because wood and plastic blades vary in density. the fan may wobble even though blades are matched # Make sure outlet box is secured to building structure, if necessary use the wood screws provide te further outlet box to joist # Make sure hanger bracket is secure to the outlet box, screws are tight.
SYMPTOM Frequency interference SOLUTION 1. Turn the power off to your ceiling fan 2. Please use a small size tool to change the frequency settings on the control system 3. Return power to the unit.
12 SPECIFICATIONS These are typical readings. Your actual fan may vary They do not include amps and wattage used by the lights] For any additional information about your Minks Aire® Ceiling fan, please write to: 2 o Fan Size Speed Volts Amps WATS RPM NW. GW CF Low 120 006 395 51 618 740 56° 1915 Extra High 120 051 4174 191 kgs kes e.
FAN SPEED AIRFLOW POWER USE AIRFLOW EFFICIENCY (CAMP {watts} {Megawatt) Low 2508 390 643 High 8177 4173 145 Tolling fan airflow ls measured in cubic fest per minute (CF. Power use Ib measured In WATS. Te maximize energy savings: + Chooses a fan with high airflow efficiency {Cravat) * Messaged tortilla + Use DOE -tarnished fighting in your fan.