Installation Guide

ManualsBrandsMinka Lavery ManualsLightingHarbor View 2-Light Sand Coal Outdoor Wall Lantern Sconce with Clear Seeded Glass

INSTALLATION INSTRUCTIONS

Model# 71262-66

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and remove the

old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear

area. Take care not to misplace any small parts necessary for

installation.

3. Screw the mounting screws (C) into mounting plate (B) ensuring they

are spaced the same distance apart as the holes in the back plate (G).

4. Attach mounting plate (B) using outlet box screws (F) to the outlet box

(A) (not supplied). The side of mounting plate marked "GND" must

face out. (Fig 1)

CONNECTING THE WIRES (Fig. 2)

5. Connect the electrical wires as shown in Fig 2. with connectors (E),

making sure that all wire connectors are secured. If your outlet box has

a ground wire (green or bare copper), connect the fixture’s ground wire

to it. Otherwise, connect the fixture’s ground wire directly to the

mounting plate (B) using the green screw (D) provided. After the wires

are connected, carefully tuck them inside the outlet box.

FINISHING THE INSTALLATION (Fig. 1)

6. Place the back plate (G) over mounting screws (C), follow by rubber

gasket (Q), then secure to wall using cap nuts (H). (Fig 1)

7. To prevent moisture from entering the outlet box (A) and causing a

short, use clear silicone sealant to outline the outside of fixture back

plate (G) where it meets the wall leaving a space at bottom to allow

moisture a means to escape. (Fig.3)

8. To replace the glass, remove gaskets (M,8pcs) and loosening the

screws (L,8pcs) to remove cover (K). Insert the new glass (J) into the

fixture frame from the bottom. Secure the lower cover (K) by screwing

screws (L,8pcs) until tight and reinstalling gaskets (M,8pcs) on the

lower cover (K).

9. Install (2) two candelabra base bulbs (I) up to 40 Watts, or CFL or LED

equivalent (not included), in accordance with the fixture specification.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

10. This fixture is ETL listed for wet location applications.

Your installation is now complete. Return power to the outlet box and test

the fixture.

Fig. 1

BAR E COPPER( GROUN D)

Fig.2

FIXTU RE

WIR ES

WHI T E

BLA C K

(HO T )

WIRES

HOU SE

GRE E N OR

WHI TE

(NE UTRAL)

WIR ES

HOUSE

(GROU N D)

COP PE R

BAR E

FIXTU R E

WIRES

BLACK

WIRES

FIX T U RE

GREEN OR

HOU SE

WIR E S

Fig

Caulking

Backplate

Mounting plate (1) (Part#A-020)

Ground screw (1)

Mounting screws (2)

Candle cover:CCV21069P-66

“CAUTION-RISK OF FIRE CONSULT A QUALIFIED

ELECTRICIAN TO ENSURE CORRECT BRANCH

CIRCUIT CONDUCTOR”

ATTENTION – RISQUE D’INCENDIE, CONSULTER UN

ÉLECTRICIEN QUALIFIÉ POUR VOUS ASSURER QUE LES

CONDUCTEURS DE LA DÉRIVATION SONT ADÉQUATS.