Installation Guide

INSTALLATION INSTRUCTIONS FOR FIXTURE #3287-589
ASSEMBLING THE FIXTURE (FIG.
1
)
1. Shut off the power at the fuse box or circuit breaker. If necessary,
remove the existing fixture and its mounting hardware from the ceiling.
2. Carefully remove the new fixture from the carton and check that all
parts are included as shown in the illustration.
3. Thread the nipple (D) into the coupling (E) and secure with hex nut.
4. Put the cap
(C) over the nipple (D) and secure with nut (B) and fixture
loop (A).
5. Adjust the arms (T) to its desired position.
6. Thread the nipple (F) into the coupling (G).
7. Assemble the fabric shade (V) onto the fixture body by tightening the
screw (W) through the holes on the fabric shade (V), bracket (U) and
the bottom end of arm (T).
8. Thread the nipple (I) into the coupling (H) and secure with hex nut.
9. Put the tube (J), tube cover (K), steel washer (L), rubber washer (M),
glass diffuser (N), rubber washer (O), steel washer (P), over the nipple
(I) in order and secure with hex nut (Q).
10. Put the cap (R) over the nipple (I) and secure with finial (S).
11. Install the light bulb in accordance with fixture’s specifications. (DO
NOT EXCEED THE MAXIMUM WATTAGE RATING!) (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
MOUNTING THE FIXTURE (FIG. 2)
12. Thread one end of nipple (S) into the crossbar (P).then place lock
washer (Q) and hex nut (R) over the end of nipple (S) ,then
thread hex
nut (R) until snug.
13. Thread the ceiling loop (T) onto the nipple (S) until snug.
14. Take this crossbar assembly and mount to the ceiling outlet box (V)
using outlet box screws (W). The side of crossbar (P) marked “GND”
must face out.
15.
Use proper chain pliers to open one end link of the chain and connect
to the fixture loop (A). Then close the link.
16. By measuring, determine the correct number of links needed for the
des
ired hanging height. Using the chain pliers, disconnect and discard
the remaining chain.
17. Slip the lock collar (Y) and canopy (U) over the chain (X). Allowing
them to rest onto the fixture loop (A).
18. Open the other end link of the chain (X) and connect to ceiling loop
(T). Then close the link.
19. Carefully lace the fixture wires through the chain (X).
20. Feed the fixture wires through the ceiling loop (T) and nipple (S) and
pull tight.
CONNECTING THE WIRES (FIG. 3)
21. At this point, connect the electrical wires as shown in Fig. 3 making
sure that all wire connections are secured. If your outlet box has a
ground wire (green or bare copper), connect the fixture’s ground wire
to it. Otherwise, connect the fixture’s ground wire directly to the
crossbar (P) using the green screw provided.
22. After the wires are connected, tuck them carefully into the ceiling
outlet box. Raise the canopy (U) to the ceiling, then raise the lock
collar (Y) and thread onto the ceiling loop (T) protruding through the
canopy (U).
Your installatio
n is now complete. Return power to the outlet box and test
the fixture.
Fig.3
Fig. 1
Fig. 2
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Set A#A
-
010
-Crossbar
-Ground Screw
-Mounting screws (2)
Chain #
HCH
2
072
-
589
Gauge 3.80MM
Notice: It is important to use proper chain pliers
(not included) to OPEN and CLOSE the chain
included with this fixture. Do not open them with
other tools that may twist or stress the chain links.
It is important to use proper chain pliers like the
ones shown in the diagram.
**the above drawing is for reference.**