Installation Guide

INSTALLATION INSTRUCTIONS
Item#2240 (New. 06/20/2013)
READ AND SAVE THESE INSTRUCTIONS
WARNING ! SHUT PO WER OFF AT FUSE OR CI R C U I T B R E AKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
LA-2291E
PREPARATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the
mounting hardware.
2. Carefully remove the fixture from the carton and check
that all parts are included as shown in the illustration.
3. Secure arms (Q) and metal ring (O) on fixture body (J)
with cap nuts (P).
ASSEMBLING THE FIXTURE (Fig. 2)
4. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the nipple (I) of the fixture body (J).
Pass the wires carefully through each rod as you
assemble. Then attach loop (H1) by screwing in to rod
(F1). Note: remove the nipple if installing with one 6”
rod only.
5. Attach the quick link (G) to loop (H1) and loop (H2) on
the canopy (D). Carefully feed the wire over loop (H1),
quick link (G) and loop (H2).
6. Thread screws (A) into the pre-drilled holes in the
circular strap (B) spaced the same distance apart as
the holes in the canopy (D).
7. Attach the circular strap (B) to the junction box using
mounting screws (C) (Size: #8-32N*L0.5”). The side of
the circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
8. At this point, connect the electrical wires as shown in
figure 3, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or bare
copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to
the circular strap using the green screw provided.
9. Tuck the wire connectors neatly into the ceiling Junction
Box and then raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
10. Thread screws (A) into canopy (D), and secure with
knurled knobs (E).
11. Place the glass shade (L) over the socket (K), then
fasten with the socket ring (M).
12. Secure metal ring (R, S) on arms (Q) with cap nuts
(T). (Confirm that larger holes on metal ring (R) are
facing upward.)
13.Install the light bulb(s) (N) (not included) in accordance
with the fixture’s specifications. (DO NOT EXCEED
THE MAXIMUM WATTAGE RATING!) (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!).
Your installation is now complete. Return power to the
junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Set# A-020
-Circular Strap
-Ground screw
-Mounting Screw*2
Rod# W30-1-281*1(F1)
W30-1-281*2(F2)
W30-H-281*1(F3)
Or: # W30-1-77*1(F1)
W30-1-77*2(F2)
W30-H-77*1(F3)
Socket ring # SKT-RING-26
B
C
E
H1
M
N
I
F3
F2
O
Q
J
K
L
P
R
S
T
A
F1
D
G
H2