Instructions / Assembly

ManualsBrandsMinka Lavery ManualsLightingBirnamwood 6-Light Koa Wood with Pewter Billiard

INSTALLATION INSTRUCTIONS

Item#1067-699 (New. 2019/12/24)

READ AND SAVE THESE INSTRUCTIONS

WARNI NG! S HUT POWE R OFF AT F USE OR CI R CUIT BRE AK ER .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Page:1/1

Fig. 1

Fig. 2

LA-3228E

PREPARATION (Fig. 1)

1. Shut of power at the fuse box or circuit breaker box and remove

the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a

clean area. Take care not to misplace any small parts necessary

for installation.

ASSEMBLING THE FIXTURE WITH CHAIN LOOP

(Fig.1&Fig. 3)

3. Place the arch (J) on the fixture body (L) and secure with screws

(K) pass the wires carefully through arch (J) as you assemble.

4. Secure the metal tube (Z) into the nipple (I) of the arch (J) pass

the wires carefully through each rod as you assemble.

5. Determine the desired hanging height and thread rods (F1, F2

and F3) to the nipple of metal tube (Z). Then attach loop (H1) by

screwing in to rod (F1). Pass the wires carefully through each

rod as you assemble.

6. Attach the quick link (G) connect to loop (H1) and loop (H2) on the

canopy (D), carefully feed the wire over loop (H1), quick link (G)

and loop (H2).

7. Thread screws (A) into the pre-drilled holes in the circular strap

(B) spaced the same distance apart as the holes in the canopy

(D).

8. Attach the circular strap (B) to the Junction box using mounting

screws (C) (Size: #8-32N*L0.5”). The side of the circular strap

marked “GND” must face out.

CONNECTING THE WIRES (Fig. 2)

9. At this point, connect the electrical wires as shown in figure 2,

making sure that all wire connectors are secured. If your outlet

has a ground wire (green or bare copper), connect the fixture’s

ground wire to it. Otherwise, connect the fixture’s ground wire

directly to the circular strap using the green screw provided.

10. Tuck the wire connectors neatly into the ceiling Junction Box and

then raise the canopy all the way to the ceiling.

COMPLETING THE INSTALLATION (Fig. 1)

11. Thread screws (A) into canopy (D), and secure with knurled

knobs (E).

12. Place the candle covers (N) over the sockets (M) of the fixture

body.

13. Install (6) six candelabra base bulbs (O) up to 60 watts each or

CFL or LED equivalent (not included) in accordance with the

fixture specification. — DO NOT EXCEED THE MAXIMUM

WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE

NOMINALE MAXIMALE!)

14. Place the glass shade (P) on the cup (Q).

Your installation is now complete. Return power to the

junction box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for

installation purposes only. It may or may not be

identical to the fixture purchased.

Set# A-020

-Circular Strap

-Ground Screw

-Mounting Screw*2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Rod# W30-1-84B*2(F1)

W30-1-84B*4(F2)

W30-H-84B*2(F3)

Candle cover# CCV24060P-84B