Installation Guide

INSTALLATION INSTRUCTIONS
For Model #1007-PL
READ AND SAVE THESE INSTRUCTIONS
WAR N I N G ! S H U T P O W E R O F F AT F U S E O R CI R C U I T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
NOTE
Turn off the main power at the circuit breaker before installing
the fixture, in order to prevent possible shock.
GENERAL
All electrical connections must be in accordance with local
and national electrical code (N.E.C) standards. If you are
unfamiliar with proper electrical wiring connections obtain the
services of a qualified electrician.
Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to lose any small parts necessary
for installation.
ASSEMBLY AND INSTALLATION
1. Turn off the power.
2. Remove the Wire Cover (10) by loosening the screw and
snapping the Wire Cover (10) with your finger.
3. Pull the supply wires and house ground wire out from the
Outlet Box (1)
4. Install the Canopy (2) to the Outlet Box (1) by using two
Mounting Screw (4) (Size: #8-32*0.5"L) (Note: The side
of the Canopy marked "GND" must face out.)
5. Position your fixture over the Outlet Box (1). Mark the
location of the two Slot Holes (7) located on the fixture
body. Remove the fixture body from the ceiling. Drill the
two Holes (5) using the appropriately sized drill bit. Insert
the provided ceiling Anchors (6) into the holes.
6. Make the wiring connections: Connect the house ground
wire to the fixture ground wire; connect the white supply
wire to the white fixture wire; connect black supply wire to
the black fixture wire using wire connectors. Carefully
tuck all wires back into the Outlet Box (1). (See Fig.4)
7. Attach the Fixture Pan (15) to the Canopy (2) through the
two Downward Screws (3) and tight it with two Nuts (8)
8. Feed the two Anchor Screws (9) through the Slot Holes
(7). Tighten the Anchor Screws (9) into the ceiling
Anchors (6) until the fixture body is flush with the ceiling.
9. Follow the drawing #3 to install the wire cover. Snap the
wire cover with your hands, then secure to the fixture
body with screw. (See Fig. 3 )
10. Install the Tube (11). Please follow the wattage label
located on the fixture body. Do not exceed the
recommend wattage. (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE) (Simultaneously
insert the pins into both ends of the fixture and rotate the
bulb until you hear and feel them lock into place)
11. Follow drawing #2 to install the Acrylic Lens (12). Hook
the Clips (14) of the lens to the curve edge of the Fixture
Pan (15) (See Fig. 2 )
12. The color correlated Temperature (CCT) for
replacing the recommended lamp is (3500K).
INSTALLATION IS NOW COMPLETED
The ballast in each of these models can be replaced by a
qualified electrician without cutting of wires and without
damage to the housing, trim, decorative elements or
carpentry to which the fixture is attached. See installation
steps for more detail.
Fig. 4
Use screw driver to loosen
the ballast screw and take it
out of fixture pan.
Insert the Ballast to the triangle
hole and then secure it by the
screw on the other end.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
LIMITED 3 YEAR WARRANTY
This Fixture is covered by a Limited 3 year Warranty from the Manufacturer,
effective from the date of purchase. This fixture is warranted against defects in
the quality of the housing, trims, diffuser, shades, and electrical components.
Fixture finishes and/or lamps (bulbs) are expressly excluded from this
warranty; refer to bulb manufacturer for lamp warranty.