...................................................................................................................................... MP10 Configuration Guide v. 1.1-SNAPSHOT Ref: MP10_CG_1.1-SNAPSHOT ......................................................................................................................................
Table of Contents ....................................................................................................................................... 1 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Charger Installation . . . . . . . . . . . . . . . . . . . . . . .
1 I n troduction 1 Introduction ....................................................................................................................................... The Mine Site Technologies MinePhone MP10 is a Voice over Wireless LAN (VoWLAN) phone designed for use in hazardous environments. It is an integral component in the MST ImPact Coal product suite, allowing for two way voice and text communication over underground wireless networks.
2 Charger Installation 2 Charger Installation ....................................................................................................................................... The MinePhone is supplied with a charging block that the handset is placed within to initiate charging. MinePhone MP10 in charging block Correctly setting up a charger for the MinePhone requires consideration of a suitable location, and ensuring power is correctly connected. 2.
3
2 Charger Installation 2.3 Indicators The charger has one LEDs on the top to indicate status.
3 Phone Configuration 3 Phone Configuration ....................................................................................................................................... MinePhones are designed to be deployed as a fleet with centralised management software, which reduces the configuration complexity operators are exposed to. Phones will by default attempt to connect to a TFTP server and download site and device specific configuration files at startup.
3 Phone Configuration 3.2 User Configurable Settings The majority of settings for the phone are site specific and are managed centrally. Users may however adjust volume and screen brightness during operation. 3.2.1 Volume During operation a user may wish to adjust the volume of ringtone and communication. Changing the volume does not require Admin access. If on a call, the volume may be adjusted using the up and down navigation button on the keypad.
3 Phone Configuration Settings configuration option in the main menu Setting Value Notes Backlight Menu select: 10s, 30s, 60s, Always Defines how long the backlight will stay on without input, default is 30s Backlight Brightness Menu select: 5%, 10%, 20%, 40%, 60%, 80%, 100% Controls the brightness of the main display, lover values conserve battery, default is 80% 3.
3 Phone Configuration DHCP Enabled To assist with commissioning of new phones, it is suggested that sites have a Wireless Access Point configured with the above network settings in a convenient location. This allows for new handsets to be turned on in range of this Access Point (AP) and retrieve the mine's specific network settings. 3.
3 Phone Configuration 3.4.1 AP Config The AP Config settings define the wireless network the handset will attempt to connect to.
3 Phone Configuration SIP Register Duration String of up to 5 digits Seconds duration between registrations, default is 120 3.4.2.2 RTP Real-time Transport Protocol settings. This settings here are specific to RTP as used by the Push to Talk functionality, and should be consistent across all phones in a fleet. The phone will require a restart to activate changes to these settings. field Values Notes RTP Port String of up to 5 digits Default is 9090 Codec Setting Menu select: g.711a, g.
3 Phone Configuration Tracker Mode Menu select: Enable, Disable Tracker Server Server name or IP address Default is Enabled 3.4.3 Internet Protocol Allows for the setting of the phone's IP address via either DHCP, or manually.
3 Phone Configuration PTT Status when Keylocked Menu select: Enabled, Disabled Default Settings Defines whether the PTT button will still work if the phone has been keylocked, default is Enabled Select to restore all Advanced settings to defaults 3.4.5 Net Search This will display a list of wireless networks the phone has detected along with current signal strength. Selecting one of the listed networks and selecting Save will autofill the SSID value under the AP Config menu to match. 3.
3 Phone Configuration Set Date and Time Adjust using navigation buttons Date Format Menu select: Y/M/D, M/D/Y, D/M/Y Time Format Menu select: 12h, 24h Default is 12h Language Menu select: English, Chinese Default is English Auto Lock Key Menu select: Enable, Disable Defines whether the keypad will lock after backlight turns off, default is Enabled Backlight Menu select: 10s, 30s, 60s, Always Defines how long the backlight will stay on without input, default is 30s Backlight Brightness Me
4 Maintenance 4 Maintenance ....................................................................................................................................... The MinePhone is an important communication device that is relied upon for safety and productivity. As such it should be treated with care and regularly maintained. 4.1 Pre-Use Inspection Before taking a MinePhone into a hazardous environment, it is the responsibility of the user to ensure that the hardware appears fit for use.
