Operating and Safety Instructions

Instructions, videos and help
can be found at:
mimosa.co/support
The following additional items are required or
recommended items for proper installation to meet
applicable local or national electrical codes or safety
standards:
• Dual-polarization access point category
antenna - the antenna must be cross-polarized
• Minimum 10 AWG (5.26 mm
2
) ground cable
with pre-terminated ring terminal
• Passive Gigabit Power over Ethernet injector
supplying between 24-57 VDC to device input
• Outdoor shielded CAT6/6A Ethernet cable
• Recommended: One (1) hose clamp pole straps
(if no integrated mount clips on your antenna)
• Recommended: Mastic sealing tape
1. Mounting
Using a hose clamp style pole strap, attach the A5x to
the desired pole by inserting the straps through the
slot in the mounting bracket, and tighten the strap.
Alternatively, attach the device to any antenna which
supports the integrated mounting clips shown below.
2. Grounding
Use minimum 10 AWG (5.26 mm2) ground wire with a
ring terminal style connector and attach to the provid-
ed grounding lug on the A5x. The ground wire should
be no longer than 1 m in length.
Hose
Clamp
Mount
Clips
To ground
3. Antenna Connection
Connect two (2) RP-SMA male type jumper cables
between the chosen antenna and the A5x and tighten
as shown below. It is recommended to optionally seal
the connectors with mastic tape for weatherproong.
4. Connect Ethernet
Connect a shielded CAT6/6A Ethernet cable (not
included) to the device, inserting it through the M25
cable sealing gland components and tighten as
shown in the diagram below. Connect the other end
of the Ethernet cable to a passive PoE power supply
(the A5x supports passive 24-57 VDC PoE input).
b
a
a
b
c
d
Safety, Warranty, & Compliance
Export Control
These commodities, technology, or software were exported from the
United States in accordance with the Export Administration Regulations.
Diversion contrary to U.S. law is prohibited.
Important Safety and Handling Information
Failure to follow any of the safety instructions in this guide, instructions
on any Airspan Networks Inc. (“Airspan”) provided packaging, and
heed WARNINGS (indicated by ), could result in re, electric shock,
other injury or death, and incur damage to this product or other proper-
ty and void the product’s Limited Warranty.
There are no End User serviceable parts inside the equipment.
Read all operating and safety instructions contained herein and accom-
panying the product as provided by Airspan:
Safety Information
Do not operate this product in any location that can be
submerged by water.
Do not install or maintain this product during the presence of an
electrical storm to avoid risk of electric shock from lightning.
Only use plastic (non-metallic) M25 cable sealing glands to
ensure comfortable surface temperature.
Failure to use shielded CAT6/6A Ethernet cabling AND to
ground the device in compliance with local and national
electrical codes could lead to serious injury or death.
This device accepts passive Power over Ethernet 24-57 VDC
powering. Connecting to any power source that does not meet
the voltage, frequency and current requirements listed may
damage the power supply or product, and pose a re hazard.
Maximum ambient operating temperature is +55ºC. Do not
operate this product above +55ºC ambient temperature.
End User Product Warranty
Mimosa products purchased from Airspan are warranted against
defects in material, and workmanship for a period of either (i) twelve
(12) months from the date of activation, or (ii) thirty-six (36) months from
the original date of shipment, whichever is earlier. Please go to www.
mimosa.co/warranty to determine whether your product is in warranty.
The sole responsibility of Airspan under this warranty shall be limited to
the repair or replacement of in-warranty defective product, at Airspan’s
sole option.
Out of warranty products shipped to Airspan will not be returned.
This warranty does not cover costs associated with the removal and/or
reinstallation of the product for repair nor for any parts that are readily
replaced in normal use.
Airspan or its designated partner will repair or replace product found to
be defective during the dened warranty period.
The End User is responsible for delivering defective product in
accordance with the Return Material Authorization (RMA) processes
published at www.mimosa.co/legal/RMA
Limitation of Warranty
The contractual product warranty is invalidated if the product is altered
or otherwise tampered with in a manner that modies the product
from its original shipping conguration and/or form factor, and could
violate the regulatory authority to operate the equipment, unless said
activity was performed by or with the written authorization of a Airspan
representative.
Modications include:
(a) External surfaces that have been painted, labeled, or otherwise
modied from the original shipping condition.
(b) Modications of the product with third party hardware, rmware,
and/or software.
(c) Any product subjected to abnormal physical or electric stress,
including, but not limited to, lightning strikes, negligence, accident,
or misuse.
(d) Any product damaged due to incorrect installation, including,
but not limited to, mounting, grounding, cabling, connectors, or
connection to power.
(e) Failure induced by connected third party products.
Failure to use minimum grade CAT6/6A shielded Ethernet cable, or
violation of local and national electric code grounding and premises
ESD protection requirements for outdoor installations will void the
product warranty.
FCC
This device complies with part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are de- signed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses, and radiates radio
frequency energy, and if not installed and used in ac- cordance with
the instructions, may cause harmful interference. However, there is no
guarantee that interference will not occur. If this equipment does cause
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to correct
the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different
from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician.
Dipole antennas may only be used indoors.
The installer is responsible for ensuring that systems employing high
gain directional antennas are used exclusively for xed, point-to-point
operations.
Industry Canada
This Class A digital apparatus complies with Canadian CAN ICES-3(A).
This Class B digital apparatus complies with Canadian CAN ICES-3(B).
Cet appareil numérique de la classe B est conforme à la norme NMB-
3(B) Canada.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is
not more than that necessary for successful commu- nication.
Pour réduire le risque d’interférence aux autres utilisateurs, le type
d’antenne
et son gain doivent être choisies de façon que la puissance isotrope
rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour
une communication réussie.
This device complies with Industry Canada licence-exempt RSS stan-
dard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Cet appareil est conforme à la norme RSS Industrie Canada exempts de
licence norme(s). Son fonctionnement est soumis aux deux conditions
suivantes:
(1) Cet appareil ne peut pas provoquer d’interférences et (2) Cet ap-
pareil doit accepter toute interférence, y compris les interférences qui
peuvent causer un mauvais fonctionnement du dispositif.
Operation in the 5150-5250 MHz band is restricted to indoor use.
Maximum antenna gain permitted for the 5725-5850 MHz band shall
be such that the equipment complies with the maximum e.i.r.p. limits
specied for point-to-point and non-point-to-point operation. When
mounting the radio antenna, in accordance with the ICES-3(B) band
requirements in section 6.2.2, the antenna must not exceed elevation
angles skyward that would exceed radiated emissions limits.
Le fonctionnement dans la bande 5150-5250 MHz est limité à une
utilisation en intérieur. Le gain d’antenne maximum autorisé pour la
bande 5725-5850 MHz doit être tel que l’équipement soit conforme
à la valeur e.i.r.p. maximum. limites spéciées pour le fonctionnement
point à point et non point à point. Lors du montage de l’antenne radio,
conformément aux exigences de la bande ICES-3 (B) de la section
6.2.2, l’antenne ne doit pas dépasser des angles d’élévation vers le ciel
qui dépasseraient les limites d’émissions rayonnées.
This radio transmitter 11823A-10000107 has been approved by Innova-
tion, Science and Economic Development Canada to operate with the
antenna types listed below, with the maximum permissible gain indi-
cated. Antenna types not included in this list and having a gain greater
than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
• 14 dBi horn antenna, 50 Ohm impedance
• 5 dBi dipole antenna, 50 Ohm impedance
Cet émetteur radio 11823A-10000107 a été approuvé par Innovation,
Sciences et Développement Économique Canada pour fonctionner
avec les types d’antennes énumérés ci-dessous, avec le gain maximum
autorisé indiqué. Les types d’antennes non inclus dans cette liste et
ayant un gain supérieur au gain maximum indiqué pour ce type, sont
strictement interdits pour une utilisation avec cet appareil.
• 14 dBi horn antenne, 50 Ohm impédance
• 5 dBi dipôle antenne, 50 Ohm impédance
European Compliance Statement
CE Marking on this product represents that this product
complies with all requirements that are applicable to it.
Europe EU Declaration of Conformity
This device can be used in the European Community. A copy of the EU
Declaration of Conformity is available at: http://bit.ly/Airspan-EU
Български (Bulgarian) - Airspan Networks Inc. декларира, че това
Airspan Networks Inc. приспособление е в съответствие със
съществените изисквания и другите приложими правила на
Директива 2014/53/EU.
Česky (Czech) - Společnost Airspan Networks Inc. tímto prohlašuje, že
tento Airspan Networks Inc. zařízení je ve shodě se základními poža-
davky a dalšími příslušnými ustanoveními směrnice 2014/53/EU.
Dansk (Danish) - Undertegnede Airspan Networks Inc. erklærer herved,
at følgende udstyr Airspan Networks Inc. enhed overholder de væsent-
lige krav og øvrige relevante krav i direktiv 2014/53/EU.
Deutsch (German) - Hiermit erklärt Airspan Networks Inc., dass sich das
Airspan Networks Inc. Gerät in Übereinstimmung mit den grundlegen-
den Anforderungen und den übrigen einschlägigen Bestimmungen der
Richtlinie 2014/53/EU benden.
Eesti (Estonian) - Käesolevaga kinnitab Airspan Networks Inc., et see
Airspan Networks Inc. seade vastab direktiivi 2014/53/EU põhinõuetele
ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English - Hereby, Airspan Networks Inc. declares that this Airspan Net-
works Inc. device is in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU.
Español (Spanish) - Por medio de la presente Airspan Networks Inc.
declara que este Airspan Networks Inc. dispositivo cumple con los
requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 2014/53/EU.
Ελληνικά (Greek) - Mε την παρούσα, η Airspan Networks Inc. δηλώνει
ότι αυτή η συσκευή Airspan Networks Inc. συσκευή συμμορφώνεται
προς τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της
Οδηγίας 2014/53/EU.
Français (French) - Par la présente Airspan Networks Inc. déclare que ce
Airspan Networks Inc. appareil est conforme aux exigences essentielles
et aux autres dispositions pertinentes de la directive 2014/53/EU.
Islenska (Icelandic) - Airspan Networks Inc. lýsir því hér með yr að
þetta Airspan Networks Inc. tæki fullnægir lágmarkskröfum og öðrum
viðeigandi ákvæðum Evróputilskipunar 2014/53/EU.
Italiano (Italian) - Con la presente Airspan Networks Inc. dichiara
che questo Airspan Networks Inc. dispositivo è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
2014/53/EU.
Latviski (Latvian) - Ar šo Airspan Networks Inc. deklarē, ka šī Airspan
Networks Inc. ierīce atbilst Direktīvas 2014/53/EU būtiskajām prasībām
un citiem ar to saistītajiem noteikumiem.
Lietuvių (Lithuanian) - Šiuo „Airspan Networks Inc.“ deklaruoja, kad šis
Airspan Networks Inc. atitinka esminius reikalavimus ir kitas 2014/53/
EUB Direktyvos nuostatas.
Magyar (Hungarian) - Alulírott, Airspan Networks Inc. nyilatkozom,
hogy a Airspan Networks Inc. eszköz megfelel a vonatkozó alapvetõ
követelményeknek és az 2014/53/EU irányelv egyéb elõírásainak.
Malti (Maltese) - Hawnhekk, Airspan Networks Inc., jiddikjara li dan
Airspan Networks Inc. tagħmir jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm d-Dirrettiva 2014/53/EU.
Nederlands (Dutch) - Hierbij verklaart Airspan Networks Inc. dat dit
Airspan Networks Inc. toestel in overeenstemming is met de essentiële
eisen en de andere bepalingen van richtlijn 2014/53/EU.
Norsk (Norwegian) - Airspan Networks Inc. erklærer herved at dette
Airspan Networks Inc. apparatet er i samsvar med de grunnleggende
kravene og øvrige relevante krav i EU-direktivet 2014/53/EU.
Polski (Polish)- Niniejszym Airspan Networks Inc. oświadcza, że ten
Airspan Networks Inc. urządzenie są zgodne z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 2014/53/EU.
Português (Portugese) - Airspan Networks Inc. declara que este Airspan
Networks Inc. dispositivo está em conformidade com os requisitos
essenciais e outras disposições da Directiva 2014/53/EU.
A5x
Flexible PTMP Access Point with
GPS/GLONASS Spectrum Reuse Sync
UNLOCK REQUIRED
This device requires
unlocking prior to
use. For all unlocking
instructions and
options prior to onsite
installation, please
visit:
mimosa.co/start