Product Requirement Specification 2.
Product Requirement Specification Revision History Version Date Authors Comments 1.0 6/24/2015 LiteOn, Reza, David Stiff Final 1.0 after Mimosa and LiteOn final review. Note: This is a living document and will be updated as product development proceeds. Author: LiteOn, Reza Reviewed and Approved by: LiteOn: Stanley Wang (6/24/15) Mimosa: David Stiff, Reza Golshan (6/24/15) Editor: David Stiff Project Leader: Reza Golshan Approval: Vice President, Product Management Mimosa Networks, Inc.
Product Requirement Specification Table of Contents 1 Product Overview ................................................................................................................................................. 4 1.1 Deployment Applications ........................................................................................................................... 5 1.2 Operational Description& Modes ...................................................................................................
Product Requirement Specification 1 Product Overview The POE Wi-Fi Router is a wall wart plug-in wireless access point with full router and multi-mode operational capabilities. It has two GigE ports one for WAN and one for LAN interface. The WAN port has as a POE injector (passive) for connecting to Mimosa devices (C5/C5c/C5i). It can be configured as a WiFi Router, Wi-Fi Extender, Range Extender, or POE pass-through.
Product Requirement Specification 1.1 Deployment Applications The deployment model of the PoE Wi-Fi Router is to provide the in-home, “final leg” portion of a Mimosa fixed wireless solution typically deployed by Wireless Internet Service Providers (WISPs). It provides the necessary WAN routing, Wi-Fi and LAN connections to bring the Internet into the home. It’s designed to be part of a complete Mimosa solution that provides easy installation and automated configuration from the Mimosa Cloud NMS.
Product Requirement Specification 1.2 Operational Description& Modes The advanced PoE Wi-Fi Router is designed to be used inside a home/small office to provide PoE power to a Mimosa C5, C5c or C5i CPE wireless device and Internet connectivity via Wi-Fi and a LAN connection. There are 4 operational modes that provide the following features and function: PoEWi-Fi Router: This mode powers the Mimosa C5/C5c/C5i CPE and provides everything needed for in-home Internet access via Wi-Fi or LAN.
Product Requirement Specification signal form the in-house main router and rebroadcasts it to create a second network (it receives, then retransmits each packet using the same radio on the same channel and with the same SSID.). It bridges the gap between the main router and the second network. The throughput loss will be more than 50%. Wi-Fi Extender: This mode is designed to extend the reach of Wi-Fi for homes/small offices with in-house LAN wiring.
Product Requirement Specification 2 Deliverables The Plug-In Wi-Fi Router with PoE and embedded software User Documentation o Quick Start Guide o Warranty/SLA o Registration card o Regulatory flyer RJ45 blocker (installed into RJ45 connector) LiteOn-designed brown box Mimosa-design giftbox (covering over brown box) One clip to each correspong SKU totally 4 SKUs Country USA, Canada, Mexico, and Japan Europe, and Russia (except UK & Ireland) UK, Ireland, Malta, Malaysia & Singapore Australia, New Zealan
Product Requirement Specification 3 Hardware requirements 3.1 Main Components Processor: MT7620A o MIPS24KEc (580 MHz) with 64KB I-cache, 32KB D-cache o 2.4GHz 802.11 b/g/n 2T×2R, 2 spatial streams Flash: 8MB SPI NOR o SDRAM: 64MB 16-bit DDR2 PoE non-standard passive PSE on WAN port at 10W 3.2 Wired Networking Interfaces 2xRJ45 o 1x10/100/1000BaseT LAN o 1×10/100/1000BaseT PoE PSE WAN port, o PoE non-standard passive PSE on WAN port at 10W 3.3 Wireless Interface IEEE802.11 b/g/n 2.
Product Requirement Specification o Antenna Gain: -4dBi or higher over 60% of all directions. Typically omnidirectional pattern, intended to radiate into a room or through a wall behind the device. o Frequency of operation at least as wide as paragraph 2.
Product Requirement Specification MCS1 15 -83 MCS2 15 -82 MCS3 15 -77 MCS4 14 -75 MCS5 14 -72 MCS6 12 -70 MCS7 12 -68 MCS8 15 -82 MCS9 15 -81 MCS10 15 -79 MCS11 15 -75 MCS12 14 -73 MCS13 14 -70 MCS14 12 -68 MCS15 12 -66 17(aggregated) -66 3.5 Other Interfaces Console: 4-pin pin header UART GPIO Test Points 3.6 Power Supply AC to DC Converter o Input Voltage: 100~240VAC, 50/60Hz o Input Current: 0.6A (RMS)@ 120VAC, 0.
Product Requirement Specification Europe, and Russia (except UK & Ireland) UK, Ireland, Malta, Malaysia & Singapore Australia, New Zealand, Type C Type G (plastic ground) Type I – 2 pin (insulated) Note: I. II. III. For the EU plug type, need the CEE 7/16 For type I socket to cover all countries we require insulated per Australia standard. Surface finish: VDI No.36 3.
Product Requirement Specification The connection bewteen the power board and the main board are two 1x4 pin headers(one for 48VDC, another for 12VDC) 3.7.1 Power Board AC to 48VDC/12VDC Converter PCB Dimensions: 83.5mm x 47.5mm x 1mm Two 1x4 pin receptacle connector to connect to the main board Two pads for interchangeable AC Clips 3.7.2 Main Board All circuit except AC/DC converter are on this board PCB dimensions: 83.5mm x 47.5mm x 1mm Two 1x4 pin header connectors to connect to the power board 3.
Product Requirement Specification Scratches when installing the AC clip are acceptable.
Product Requirement Specification Long Side View – Stackup Analysis Mimosa Confidential Page 15
Product Requirement Specification Short Side View: Outline Dimensions (length) Long Side View: Outline Dimensions (length) Mimosa Confidential Page 16
Product Requirement Specification 3.9 LED Indicators The functions of each LED shall be implemented in software. The table below WAN (green/red) Link on RJ45 WAN C5 CPE status LAN (green/red) Link on R45 LAN Wi-Fi (blue) Link on 11n 2.4G Wi-Fi System Status During Boot 3.9.1 Green Yellow Red Green Yellow Passthrough Range Extender NOTE: No LEDs on the RJ-45 Ethernet connectors Wi-Fi Extender LEDs Description – 3 LEDs Wi-Fi Router defines the functions of each LED.
Product Requirement Specification 3.10 Reset Button The reset button can be accessed through a pinhole with a paperclip or sharp object. Press and release the reset button to reboot the router.
Product Requirement Specification 4 SW Features Version 1.6 – May 22, 2015 David Stiff, Mimosa Networks ʔ Interface Use Case Diagram (diagram 1) This table describes the basic connection description and requirements for the ports on the PoE Wi-Fi Router.
Product Requirement Specification Mimosa Confidential Page 20
Product Requirement Specification This table describes the four operational modes for the PoE Wi-Fi Router and what functions are enabled for each mode.
Product Requirement Specification ʔ Router and auto-configured as Wi-Fi Extension. I.e.: Plug is once to configure as Wi-Fi Extension and then power on again w/out connecting to main router. Configured manually via GUI Enable Wi-Fi as repeater WAN Router (NAT/DHCP) OFF Bridge traffic to LAN if connected Bridge traffic to the main Wi-Fi router ʔ Wireless Extension and Repeater Use Case (diagram 2) This table describes the minimum viable feature set for the PoE Wi-Fi Router.
Product Requirement Specification Closed Network Guest SSID ʔ Option to hide SSID, configurable per SSID Option to make an SSID a Guest SSID Create Guest SSID as WPA/WPA2 with default (no captive portal) Default SSID = GuestXYZ (last 3 digits of serial number) WPA passphrase = guestXYZ (last 3 digits of serial number) Range Extender (repeater) Site Survey Security Authentication Allow option to enable client isolation to only allow Guest Wi-Fi traffic to go to internet (WAN) Site Survey Mode to disco
Product Requirement Specification Rate Limiting on WAN Static routes DHCP Server for LAN and Wireless clients PPPoE client For Authentication Route Name, Destination IP, IP Subnet Mask, Gateway IP Address Domain Name, Start IP, End IP, Lease Time (hours: default 24 Hr, range options 1-900 Hr) MAC Address based static assignment (Name, IP address, MAC Address) Check if IP in use before assigning to prevent duplicate IP addresses DHCP Lease Display Table PPP username/password Authentication options: Auto
Product Requirement Specification Statistics SNMP Wireless ACL DHCP Failover IP assignment if no DHCP response (IP, Netmask, Gateway, DNS1, DNS2) Statistics of wired, wireless associated stations accessible MIBII (survey throughput, data statistics, location) SNMP Community String RO setting Based on MAC address (White List & Black List individual MAC Addresses) via Web UI Firmware upgrade System log Internal (WebUI) and External (Syslog) Set External Syslog server IP Ping, Traceroute Diagnostics C
Product Requirement Specification Fail = no ping response Internet Access (TCP) TCP connectivity (tcping) to well known global web sites: mimosa.co google.com youtube.com facebook.com independent.co.uk buzzfeed.com upsocl.com scribd.com ask.fm diply.com baidu.com Success = successful tcp connection to any of above sites. Fail = failed tcp connection to all sites Internet Access (DNS) DNS Server availability. Successful DNS lookup for above names. This is the DNS server from the WAN side of the router.
Product Requirement Specification Mimosa Confidential Page 27
Product Requirement Specification 5 Environmental Operating: o Temp: 0° C to +40° C (32° F to +104° F) o Humidity: 5% to 95% non-condensing Storage and Transportation Temperature Range: o Temp: -25° C to +65° C (-13° F to +149° F) Mimosa Confidential Page 28
Product Requirement Specification 6 Reliability MTBF: >50,000 hours Mimosa Confidential Page 29
Product Requirement Specification 7 Regulatory and Certifications EN55022/24 Class B EN 300 328 EN 301 489 Part 1 EN 301 489 Part 17 UL/cUL/IEC/EN 60950 IC RSS247 CE Marked SAA/RCM with RCM logo marked FCC Part 15B+15C TUV (EN60950-1 + EN61984) RoHS Compliance Wi-Fi Alliance Wi-Fi CERTIFIED™ Mimosa Confidential Page 30
Product Requirement Specification FCC WARING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Product Requirement Specification IC WARING STATEMENT RSS-Gen Issue 4 8.4 This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Product Requirement Specification IC Radiation Exposure Statement: mobile device This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition de rayonnement de la IC RSS-102 rf déterminées pour un environnement non contrôlé.
