Operator's Manual

TICK™ TOOL & EQUIPMENT TRACKER
IMPORTANT SAFETY INSTRUCTIONS
WARNING
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result
in electric shock, re and/or serious personal injury.
1. SAVE THESE INSTRUCTIONS - THIS OPERATOR’S MANUAL CON-
TAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS.
2. THIS DEVICE IS DESIGNED TO BE POWERED BY (1) CR2032
BATTERY PROPERLY INSERTED. Do not attempt to use with any
other voltage or power supply.
3. CHEMICAL BURN HAZARD. KEEP BATTERIES AWAY FROM
CHILDREN.
4. THIS DEVICE CONTAINS A LITHIUM BUTTON/COIN
CELL BATTERY. A NEW OR USED BATTERY CAN
CAUSE SEVERE INTERNAL BURNS AND LEAD
TO DEATH IN AS LITTLE AS 2 HOURS IF SWAL-
LOWED OR ENTERS THE BODY. Always secure the
battery cover. If it does not close securely, stop using
the device, remove the batteries, and keep it away from children. If
you think batteries may have been swallowed or entered the body,
seek immediate medical attention.
5. INSTALL BATTERY ACCORDING TO POLARITY (+ / -) DIAGRAMS.
6. PROPERLY DISPOSE OF USED BATTERIES IMMEDIATELY.
7. DO NO INCINERATE OR DISMANTLE BATTERIES.
8. UNDER ABUSIVE CONDITIONS, LIQUID MAY BE EJECTED FROM
THE BATTERY, AVOID CONTACT. IF CONTACT ACCIDENTALLY
OCCURS, FLUSH WITH WATER. IF LIQUID CONTACTS EYES,
ADDITIONALLY SEEK MEDICAL HELP. Liquid ejected from the
battery may cause irritation or burns.
9. DO NOT DISPOSE OF DEVICE OR BATTERIES TOGETHER WITH
HOUSEHOLD WASTE MATERIAL! Appliance and batteries that
have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
SYMBOLOGY
Volts
Direct Current
Read operator's
manual.
SPECIFICATIONS
Cat. No. .......................................................................................ONET
Volts .............................................................................................3VDC
Battery Type ............................................................................ CR2032
Battery Life ..................................................................................... 1 yr
Recommended Ambient Operating Temperature ...........-28°C to 60°C
Signal Range .................................................................≥ 30.5m (100')
Ingress Protection..........................................................................IP67
Impact Protection...........................................................................IK08
GENERAL USE AND CARE
Coincell Battery
Before rst use, remove the plastic tab from between the battery and
contacts. Discard the plastic tab and replace the cap. Remove the clear
protective backing from the back of the TICK™.
If the TICK™ will not be used for a long time, remove the battery as a
protection against corrosion.
1. Open the TICK™ Tracking Device by rotating the cover.
2. Remove the CR2032 coincell battery.
3. Remove the clear protective lm (rst time only).
4. Replace the CR2032 coincell battery, positive (+) side up.
5. Replace cover and rotate to lock.
6. Remove the clear protective backing on the bottom of the Tick (rst
time only).
ONE-KEY™ App / Account Set Up
1. To download the ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
2. Create a Username and Password and log in to a ONE-KEY™
account.
3. Bluetooth and Location Services must be enabled on the mobile device.
4. Location Services must be enabled in the Settings section of the App.
QUICK START GUIDE
OPENING THE TICK
™
ACTIVATING THE TICK
™
Fig. A
ROTATE LID
Fig. B
REMOVE COVER
AND BATTERY
1. Download ONE-KEY
™
app and log in
2. Remove protective cover from battery
and back of TICK
™
3. Add or select item
from app inventory
4. Tap ASSOCIATE TICK
™
button in app and follow
steps to activate TICK
™
5. Attach TICK
™
to item and start tracking
ASSOCIATE TICK
™
Activating the TICK™
1. Select or add a new item in "Inventory" to be tracked using the TICK™.
2. Select the red “Associate Tick” button on the Inventory Item Detail
screen.
3. Follow the instructions on the screen.
4. Select "Start Scan". The App will scan for TICKs in range. If there are
too many in range, move the others at least 90cm away.
5. Once the App has paired a TICK™ with the Inventory Item, tracking
can begin.
NOTE: If the device receives a sharp blow or impact, it may need to
be paired again.
Installing the TICK™
The TICK™ is designed to track tools and equipment using the ONE-
KEY™ App. It will not prevent theft from happening. The TICK™ can
be installed in a variety of orientations. Consider installing the Tick™
to prevent tampering.
Be sure battery door can be removed once installed.
The Tick™ can be installed using the following attachment options
• #8 Pan Head Self Tapping Screw • Glue or Epoxy
• 5/32 Diameter Rivet • Adhesive Backing
• Cable or Zip Tie • Keyring
WARNING! Do not secure in such a way as to impede the safe use
of the product.
Do not attach on or near the following:
• vents • moving parts
• safety notications • guards
• hand holds • switches or controls
• areas exposed to sparks or heat
Before using screws or rivets, ensure the space behind the placement
is clear.
Care
• Clean with a damp, soft cloth.
• Never use aggressive cleaning agents or solvents.
WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
.
Please refer to Australian and New Zealand warranty supplied with tool.
This warranty applies only to product sold in Australia and New
Zealand.
MILWAUKEE
®
prides itself in producing a premium quality product that
is Nothing But Heavy Duty
®
. Your satisfaction with our products is very
important to us! If you encounter any problems with the operation of this
tool, please contact your authorised MILWAUKEE
®
dealer.
For a list of MILWAUKEE
®
dealers, guarantee or service agents please
contact MILWAUKEE
®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 279 624)
or visit www.milwaukeetools.com.au / www.milwaukeetools.co.nz.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Electric Tool Corporation (Australia)
Techtronic Industries (Australia) Pty. Ltd.
Rowville, Victoria, Australia, 3178
Milwaukee Electric Tool Corporation (New Zealand)
Techtronic Industries (New Zealand) Pty. Ltd.
Mangere, Auckland, New Zealand, 2022
Professionally made in China for Milwaukee Electric Tool Corporation
V