M18 FCHS Original instructions
M18FHCS Original instructions Originalbetriebsanleitung Notice originale Istruzioni originali Manual original Manual original Oorspronkelijke gebruiksaanwijzing Original brugsanvisning Original bruksanvisning Bruksanvisning i original Alkuperäiset ohjeet Algupärane kasutusjuhend Πρωτότυπο οδηγιών χρήσης Оригинальное руководство по эксплуатации Orijinal işletme talimatı Původním návodem k používání Оригинално ръководство за експлоатация Pôvodný návod na použitie Instrucţiuni de folosire originale Instrukcją
I II III IV V VI VII VIII IX Technical Data, Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
1 3 4 2 6 5 7 8 9 10 11 12 13 14 15 16 2 17 18
1. 2. I 1. 2.
78-100 % I 55-77 % 33-54 % 10-32 % <10 % 4
64 1394 : NP PAS 1. II 2. 3. 2 1 2 4.
PAS III 1. 2. + 3. 4. 6 - 3 mm 5.
1. 2. 10 min 3. IV 4.
V Insulated gripping surface 8
Start V 1 2 3 4 Carry out a test cut 9
Stop 2 V 1 3 4 10
1. 2.
VI 1/3 2 2/3 1 1 12 2/3 2 1/3
VI 1 2 3 13
VI 2 1 min 50 mm 2 1 45° 1/3 14 3 2/3
1. 2. VII 3.
94 : NP PAS 1. 1 VIII 2 2. 3.
94 : NP PAS 4. VIII 5. A 5.
TECHNICAL DATA Chain saw Production code IX M18 FCHS No-load chain speed Bar length max. Usable cutting length Battery voltage Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 12,0 Ah) Recommended Ambient Operating Temperature Recommended battery types Recommended charger Chain oil tank capacity Noise information Measured values determined according to EN 60745.
When cutting a limb that is under tension, be alert for spring back. When the tension in the wood fibres is released the spring loaded limb may strike the operator and /or throw the chain saw out of control. Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance. Carry the chain saw by the front handle with the chain saw switched off and away from your body.
Do not put pressure on the saw at the end of the cut.Be ready to take on the weight of the saw as it cuts free from the wood.Failure to do so could result in possible serious personal injury. Do not stop the saw in the middle of a cutting operation. Keep the saw running until it is already removed from the cut.Do not fix the on/off switch in the „on“ position when using the saw hand-held. Remove the battery pack before starting any work on the appliance.
SAFETY DEVICES WARNING! Consequences of improper maintenance, removal or modification of safety features like the chain brake, ignition switch, hand guard (front and back), spiked bumper, chain catcher, guide bar, low kick-back saw chain may cause the safety features to not function correctly, thus increasing the potential for serious injury. Low kick-back saw chain A low-kick-back saw chain helps to reduce the possibility of a kickback event.
Removing buttress roots A buttress root is a large root extending from the trunk of the tree above the ground. Remove large buttress roots prior to felling. Make the horizontal cut into the buttress first, followed by the vertical cut. Remove the resulting loose section from the work area. Follow the correct tree felling procedure after you have removed the large buttress roots. Limbing a tree Limbing is removing the branches from a fallen tree.
RISK REDUCTION • It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness, and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms.
Keep the reservoir more than ¼ full to ensure sufficient oil is available for the job. Note It is recommended to use a vegetable based chain oil when pruning trees. Mineral oil may harm trees. Never use waste oil automotive oil, or very thick oils. These could damage the chain saw.Clear surface around the oil cap to prevent contamination. 1. Unscrew and remove the cap from the oil tank. 2. Pour the oil into the oil tank and monitor the oil level gauge. 3. Put the oil cap back on and tighten it up.
BATTERY PACK PROTECTION Maintenance schedule Daily check Bar lubrication Chain tension Chain sharpness For damaged parts For loose fasteners Chain brake function Guide Bar Complete saw Chain Brake Before each use Before each use and frequently Before each use, visual check Before each use Before each use Before each useInspect and clean Before each use After each use Every 5 hours of operation In extremely high torque, binding, stalling and short circuit situations that cause high current draw, t
GB-DECLARATION OF CONFORMITY We declare as the manufacturer under our sole responsibility that the product described under „Technical Data“ fulfills all the relevant provisions of the following Regulations S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended), S.I.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
