M18 BLTRC Original instructions
M18 BLTRC Original instructions Originalbetriebsanleitung Notice originale Istruzioni originali Manual original Manual original Oorspronkelijke gebruiksaanwijzing Original brugsanvisning Original bruksanvisning Bruksanvisning i original Alkuperäiset ohjeet Algupärane kasutusjuhend Πρωτότυπο οδηγιών χρήσης Оригинальное руководство по эксплуатации Orijinal işletme talimatı Původním návodem k používání Оригинално ръководство за експлоатация Pôvodný návod na použitie Instrucţiuni de folosire originale Instrukc
I II III IV V VI VII Technical Data,Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
M8 M6 I M8 M6 M12 M10 M10 2 M12
II 1. 2. 3. 4. 5. 6.
78-100 % III 55-77 % 33-54 % 10-32 % <10 % 4
1. 2. III 1. 2.
1. 2. 90° min 50 mm IV 3. START 2 1 6 4.
1. 2. IV 90° mm min 10 3. START 4.
1. 2. 2 V START 1 STOP 1 2 3. 4.
VI Ident-Nummer: 4932 4713 72 9
TECHNICAL DATA Threaded Rod Cutter Production code Battery voltage Cutting range Steel Cutting range Stainless steel Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah...12,0 Ah) Recommended Ambient Operating Temperature Recommended battery types VII M18 BLTRC 4775 24 02... ... 000001-999999 18 V M6x1 M 8 x 1,25 M 10 x 1,5 M 12 x 1,75 M6x1 M 8 x 1,25 M 10 x 1,5 3,9 kg…5,0 kg M18B... M18HB... M12-18...
To avoid injury and damage, prevent accidental starting of the device. Never hold the tool in the area of jaws and cutting dies. Before using, always check the dies and jaws for cracks and other signs of wear. Only use the threaded rod cutter, battery pack and charger if they are in perfect technical condition. Have damage repared immediately by an authorised workshop. Remove the battery pack before starting any work on the appliance. Do not use tool without dies installed.
Reverse Button If the cutting jaws need to be opened without completing the cutting cycle: 1. Release the trigger. 2. Press the reverse button . The button light will turn ON. 3. Pull the trigger and hold the tool firmly until the cutting jaws open fully. NOTE: The tool will only enter reverse mode if the jaws are NOT fully open. Jammed Cutting Dies Dirt and debris can cause the cutting dies to become jammed together after a cut. If the tool shuts off and the cutting jaws are still closed: 1.
EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives 2011/65/EU (RoHS) 2006/42/EC 2014/30/EU and the following harmonized standards have been used. EN 62841-1:2015 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 SYMBOLS Please read the instructions carefully before starting the machine. Always wear goggles when using the machine.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
