M18 BLCS66 Original instructions
M18 FCS66 Original instructions Originalbetriebsanleitung Notice originale Istruzioni originali Manual original Manual original Oorspronkelijke gebruiksaanwijzing Original brugsanvisning Original bruksanvisning Bruksanvisning i original Alkuperäiset ohjeet Algupärane kasutusjuhend Πρωτότυπο οδηγιών χρήσης Оригинальное руководство по эксплуатации Orijinal işletme talimatı Původním návodem k používání Оригинално ръководство за експлоатация Pôvodný návod na použitie Instrucţiuni de folosire originale Instrukc
I II III IV V VI VII VIII IX X XI XII 90° Technical Data,Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
1. I 2 1 2.
1. II 1 2 2.
3. II EN 847-1 4.
5. 1 II 2 6.
1. 2. III 1. 2.
TIP III 78-100 % 55-77 % 33-54 % 10-32 % <10 % 8
STOP START 2 1 IV 2 1 For safety reasons this power tool is fitted with a switch lock and the On-/Off switch cannot be locked in the „On“ position 9
IV Insulated gripping surface 10
V Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.
1. 2. V 0-6 4 2 0 3.
1. 2. VI 50 45 40 30 20 10 0 3. 4.
1. 2. VII 2 1 3.
1. 2. START VIII 1 2 3. 2. 0° 4.
1. VIII 0° > 0° 2. 3. START 1 2 4. 16 5. 2. 6.
A IX B max.
IX 18
90° 2. 90° 1. X 0° If a correction of the 90° angle of the guide-plate to the saw blade is necessary, use the correction screw.
90° 90° 3. X + + – 90° 4.
1. A AS 2-250 4931 4472 95 B AS300 AS-30 AS-42 4931 4472 94 1 XI 2 2.
TECHNICAL DATA Circular saw Production code XII Battery voltage No-load speed Saw blade dia. x hole dia Saw blade thickness Blade teeth Max. Cutting depth at 0° / 45° / 50° Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 5,0 Ah) Recommended Ambient Operating Temperature Recommended battery types Recommended charger Noise information Measured values determined according to EN 62841.
h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation. b) Check the operation of the lower guard spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris.
ELECTRIC BRAKE The electric brake engages when the trigger is released, causing the blade to stop and allowing you to proceed with your work. Generally, the saw blade stops within two seconds. However, there may be a delay between the time you release the trigger and when the brake engages. Occasionally the brake may miss completely. If the brake misses frequently, the saw needs servicing by an authorized Milwaukee service facility.
EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives 2011/65/EU (RoHS) 2006/42/EC 2014/30/EU and the following harmonized standards have been used. EN 62841-1:2015 EN 62841-2-5:2014 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 SYMBOLS CAUTION! WARNING! DANGER! Please read the instructions carefully before starting the machine. Always wear goggles when using the machine.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
