M12 FDGS Original instructions
M12 FDGS Alkuperäiset ohjeet Algupärane kasutusjuhend Πρωτότυπο οδηγιών χρήσης Оригинальное руководство по эксплуатации Orijinal işletme talimatı Původním návodem k používání Оригинално ръководство за експлоатация Pôvodný návod na použitie Instrucţiuni de folosire originale Instrukcją oryginalną Оригинален прирачник за Eredeti használati utasítás работа Izvirna navodila Оригінал інструкції з Originalne pogonske upute експлуатації Instrukcijâm oriěinâlvalodâ Originali instrukcija ø 6 mm 2 15 ø 8 mm 17
I II III 22 1 1 IV V VI 33 Technical Data,Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
1. I Sd1 = Sd2 Sd2 Sd1 L3 = min. 10 mm Sd 1 Sd 2 D L3 L0 T 3. 17 2.
4. I ø 8 mm 5. 17 15 6.
1. 2. 1. 2.
22 1 1 33 n ≤ nmax.
25 % 2 6 50 % 75 % 100 % IV 4x <10 % Start 2 sec 1
Load-dependent motor protection: If the motor is overloaded, the overload protection will trip. To continue working, switch the machine off and then on again. If the battery becomes too hot, the fuel gauge lights will flash in an alternating pattern and the tool will not run. Allow the battery to cool down.
V 8
TECHNICAL DATA Fuel Straight Die Grinder Production code M12 FDGS 4748 00 02... ...000001-999999 12 V 0-10000 / 0-15000 / 0-21000 min-1 6,0 mm 8,0 mm 50 mm 0,7... 1,0 kg -18°C ... +50°C M12B... C12C; M12C4; M12-18... Battery voltage Rated speed 1 / 2 / 3 Collet diameter Collet diameter Abrasive grinding body diameter max. Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah...
bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time. h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments.
away from the operator, depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions. Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces.
VI WARNING! To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., Can cause a short circuit. Do not use this tool to work on asbestos-containing products. Determine the composition of the workpiece before beginning work.
EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives 2011/65/EU (RoHS) 2006/42/EC 2014/30/EU and the following harmonized standards have been used. EN 60745-1:2009+A11:2010 EN 60745-2-23:2013 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 SYMBOLS CAUTION! WARNING! DANGER! Please read the instructions carefully before starting the machine.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
