AG 22-180 AGV 22-180 E AG 22-230 AGV 22-230 AG 22-230 E AGV 22-230 E Original instructions
I II III IV V VI TIP VII VIII Technical Data,Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
AG 22-180, AG 22-230, AG 22-230 E I AGV 22-180 E, AGV 22-230, AGV 22-230 E 2
AGV 22-180 E AGV 22-230 AGV 22-230 E II II 1. 2. 3.
AG 22-180 AG 22-230 AG 22-230 E II 1. 1 2 2. 4 3.
B ° 60 60 30 ° A III 0° ° 3 0° 1 1 5
Use only spindle nuts as provided by the manufacturer. 1. IV 6 2.
3. < 6 mm 4. > 6 mm IV 1. 2. 3. 4.
Startup protection: When switched on, the machine will not start up after voltage breakdown. To continue working, switch the machine off and then on again. AGV 22-180 E AGV 22-230 E AG 22-230 E . Switch can be locked V Start 2 3 1 1. 2. 3.
AG 22-180 AG 22-230 AGV 22-230 Startup protection: When switched on, the machine will not start up after voltage breakdown. To continue working, switch the machine off and then on again. . DEADMAN V 4931 4318 34 220 – 240 V 50 – 60 Hz 10,2 A 2200 W Code: 4000 4318 31 XXXXX MJJJJ n = 8500 min-1 Ø max.
TIP TIP VI < 30° 10
Accessory 1. 2. VII 1. 2.
Accessory 1. 2. 1. 2.
TECHNICAL DATA Angle Grinder AG 22-180 (110-120 V) AG 22-180 (220-240 V) 2200 W 8500 min-1 180 mm 22,2 mm AGV 22-180 E AG 22-230 (220-240 V) (110-120 V) 4318 21 04... 4336 26 04... ... 000001 4318 66 04... -999999 ... 000001 -999999 2200 W 2100 W -1 8500 min 6600 min-1 180 mm 230 mm 22,2 mm 22,2 mm AG 22-230 (220-240 V) 4318 41 04... 4460 36 04... ... 000001 -999999 2200 W 6600 min-1 230 mm 22,2 mm Production code 4336 21 04... ... 000001 -999999 4318 31 04... ...
TECHNICAL DATA Angle Grinder AGV 22-230 (110-120 V) AGV 22-230 (220-240 V) AG 22-230 E (220-240 V) Noise information Measured values determined according to EN 60745.
l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. n) Regularly clean the power tool’s air vents.
VIII do not allow any interference of the wire wheel or brush WORKING INSTRUCTIONS with the guard. Wire wheel or brush may expand in diameter due For accessories intended to be fitted with threaded hole wheel, to work load and centrifugal forces. ensure that the thread in the wheel is long enough to accept the spindle length. Additional Safety and Working Instructions Always use and store the cutting and grinding disks according to When grinding metal, flying sparks are produced.
EC-DECLARATION OF CONFORMITY We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives 2011/65/EU (RoHS) 2006/42/EC 2014/30/EU and the following harmonized standards EN 60745-1:2009 + A11:2010 EN 60745-2-3:2011+A2:2013 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 AGV 22-180 E, AGV 22-230, AG 22-230 E, AGV 22-230 E: EN 61000-3-2:2014 EN 61000-3-3:2013 AG 22-180, AG 22-230: EN 61000-3-11:2000 have been used.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
