Cut Sheet

ManualsBrandsMilwaukee ManualsBladesCUTTING WHL 12 X 1/8 X 1

Page 1 of 2 Revision Date: September 2004

METCo P/N: 58-97-0080

Legend: Drawing No.: 1A

Y - Yes

N - No

N/A – Not Applicable

Material Safety Data Sheet

May be used to comply with

OSHA’s Hazard Communication Standard 29 CFR 1910.1200.

This standard must be consulted for specific requirements

IDENTITY (As used on label and list)

Note: Blank spaces are not permitted. If any item is not applicable, or no information

is available, the space must be marked to indicate that.

Cut-Off Wheels

49-94-1470, 49-94-1475, 49-94-1480, 49-94-1485, 49-94-7050

Section I

Manufacturer’s Name

Emergency Telephone Number

Milwaukee Electric Tool Corporation 1-800-424-9300

Address (Number, Street)

Contact Telephone Number for Technical Information

13135 West Lisbon Road 262-781-3600 or 1-800-729-3878 (1-800-SAWDUST)

(City, State, and Zip Code) Date Prepared

Brookfield, Wisconsin 53005 September 2004

Section II - Hazardous Ingredients/Identity Information

Hazardous Components [Specific Chemical Identity, Common name (s)]

Ingredient % by

Weight

OSHA Reg.

Y/N

CAS #

OSHA

PEL

ACGIH

TLV

California

Prop 65 Reg.

Y/N

IARC/NTP

Y/N

Aluminum Oxide, Non-Fibrous 90-95% N 1344-28-1 15mg/m3 10mg/m3 N N

Cured Phenol/Formaldehyde Resin 3-6% N 9003-35-4 N/A N/A N N

Fiberglass 1-3% N 65997-17-3 1fbr/cc N/A N N

Iron Disulfide 1-3% N 12068-85-8 10mg/m3 10mg/m3 N N

DOT Hazard Classification: Non-Hazardous

SARA Title III Section 313: This product does not contain regulated levels of any toxic chemical subject to the reporting requirements of section 313 of

Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 372.

HMIS

Rating Numbers

Health Flammability Reactivity Personal Protection

1 0 0 A

Hazard Ratings: 0 = Minimum hazard 1 = Slight hazard 2 = Moderate hazard 3 = Serious hazard 4 = Severe hazard

A = Goggles B = Goggles + Gloves C = Face Shield, Gloves + Apron X = Special, See sections VII & VIII of this sheet

Section III - Physical/Chemical Characteristics

Boiling Point

Specific Gravity (H

O=1)

N/A N/A

Vapor Pressure (mm/Hg.) Melting Point

N/A N/A

Vapor Density (Air=1) Evaporation Rate

N/A N/A

Solubility in Water

Non-Soluble

Appearance and Odor

Solid article. Odorless.

Section IV - Fire and Explosion Hazard Data

Flash Point (Method Used) Flammable Limits LEL UEL

N/A N/A N/A N/A

Extinguishing Media

N/A

Special Fire Fighting Procedures Unusual Fire and Explosion Hazards

N/A N/A

Section V - Reactivity Data

Stability Unstable

Conditions to avoid

Stable

X N/A

Incompatibility (Material to avoid):

Avoid acids of all types with a pH < 4.0

Summary of content (2 pages)

PAGE 1
Material Safety Data Sheet May be used to comply with OSHA’s Hazard Communication Standard 29 CFR 1910.1200. This standard must be consulted for specific requirements IDENTITY (As used on label and list) Note: Blank spaces are not permitted. If any item is not applicable, or no information is available, the space must be marked to indicate that.
PAGE 2
Hazardous Decomposition or Byproducts In use, dust and decomposing odors may be generated. In most cases, the material removed from the workplace will be significantly greater then the grinding wheel components. Coolants may produce other decomposition products. For products containing phenol and formaldehyde resin, thermal decomposition may produce trace amounts of phenol and formaldehyde. For products containing inorganic fluorides, thermal decomposition may produce trace amounts of fluorides.